Advertisement
NETWORK CABLE INSTALLATION
A 100' Cat5e non-plenum UTP camera cable is included with your camera. It is
important to consider how the network cable is attached to the camera.
•
If passing the cord through a wall or ceiling, drill a 7/8" hole.
•
We recommend using the waterproof cable connector on all installations.
•
For maximum weather and tamper resistance in outdoor installations, place
the connection between your camera cable and the camera jack within a wall
or use a wall mount or junction box available at avertx.com.
•
For outdoor installations, use silicone caulking to seal any holes in the wall or
ceiling to protect against leaks.
•
If your installation is in a commercial building, consult local fire codes. Plenum
rated cable may be required.
WATERPROOF CABLE CONNECTOR
To use the IP66-rated waterproof cable connector:
You do not need to re-terminate the cable to use the waterproof cable connector.
•
Slide all pieces of the waterproof cable connector over the cable plug in this order:
1. Small plastic ring
2. Flexible silicone seal ring. You will need to stretch the silicone seal over
the RJ-45 plug.
3. Large plastic ring
•
Slide the rubber "O" ring over the camera plug screw and connect the camera
cable to the plug on the dongle. Screw the large plastic ring into the dongle.
•
Insert the flexible silicone seal into the "crown" section of the large plastic ring
•
Screw the small plastic ring into the large plastic ring
AUTOFOCUS ZOOM LENS
The HD838IRM Dome Camera is equipped with an Auto Focus Zoom lens. Do not
attempt to manually focus this camera. Activating the zoom will focus the camera.
To activate zoom and focus the camera: In Live view, right click on the desired
camera pane and select zoom in. Right-click and zoom out when the camera
finishes focusing.
Copyright © 2019 AvertX. All rights reserved. Information contained in this document is subject to
change without prior notice. AvertX does its best to provide accurate information, but cannot be held
responsible for typos or mistakes.
CONNECTING TO THE CAMERA
This camera is plug and play when connected to an AvertX ProConnect Recorder.
To access this camera without an AvertX recorder, you will need to connect the
camera to a Power Over Ethernet Switch and install AvertX Network Camera
Manager Software on a Windows computer.
1. Download and install the Camera Finder software at www.avertx.com/downloads/.
Select ONVIF Detection, and click Refresh.
2. When the camera is found, click "Load" under the web page. The camera admin
page will load in a browser.
3. Login to the camera using the username admin. The first time the camera is
accessed you will need to set a password.
4. AvertX cameras are set to DHCP by default. If a DHCP server is not detected
after 4 minutes, the camera will default to IP address 192.168.51.2.
5. For assistance connecting directly to your camera, please contact AvertX
support at 855-228-3789
MICRO SD CARD AND RESET BUTTON
Your HD838IRM camera is equipped with a slot for a microSD card and a Reset
button. To access these, you must remove the microSD / Reset cover.
If you have purchased a microSD card to be used for backup, insert the formatted
card into the slot. Refer to the user manual for compatible cards and how to
properly format your microSD Card.
Use the reset button to restore the factory default settings. To reset your camera:
1. Disconnect the cat5e cable from the camera for 30 seconds.
2. Hold the reset button down while reconnecting cat5e.
3. The IR lights will illuminate when power is reconnected; continue holding the
reset button until the IR lights turn off (approximately 30 seconds).
4. Allow 2 minutes before attempting to rediscover camera.
Reset button
FOR FURTHER INSTRUCTIONS:
For more information on installing your AvertX camera, download the
user manual, read FAQs and DIY resources, and view instructional videos
at www.avertx.com.
Contact AvertX Support: 1-855-228-3789 | www.avertx.com
microSD Slot
37024AB
Advertisement
