Advertisement
INSTALLATION
Wall or Ceiling
1.
Drill a 1" hole in the wall or ceiling for the cable.
2.
Drill four 1/4" holes and insert the included anchors.
3.
Attach the cables and tighten the included screws to
mount the camera to the wall or ceiling.
4.
Attach the sunvisor using the included sunvisor bolt.
5.
Use the inculded 3mm hex-head wrench to loosen the
adjustment bolt.
6.
Aim the camera and tighten the bolt to complete the
installation.
CAMERA OSD MENU
EXPOSURE
LENS
MANUAL
BRIGHTNESS
0 ~ 99
SELECT
E. SHUTTER
AUTO, 1/60 ~
1/100000
DC
BRIGHTNESS
0 ~ 99
E. SHUTTER
AUTO, 1/60 ~
1/100000
AGC
OFF, LOW, MIDDLE, HIGH
Auto Day/Night is
disabled if AGC is
OFF
SENSE-
AUTO, OFF, X2, X4, X8, X16,
Use sense-up in low
UP
X32, X64, X128, X256, X512,
light environments
X1024
BACK-
BLC
BLC LEVEL
OFF, LOW, MID,
LIGHT
HIGH
TOP
0 ~ 15:
BOTTOM
0 ~ 16
LEFT
0 ~ 15
RIGHT
0 ~ 16
HLC
HBLC
OFF
MANUAL HBLC LEVEL:
OFF,LOW, MID, HIGH
TOP, BOTTOM, LEFT, RIGHT
same as BLC
MODE
ALL DAY, NIGHT
HLC LEVEL
1 ~ 100
MASK 1-4
ON
TOP: 0 ~ 33
BOTTOM: 1 ~ 34
LEFT: 0 ~ 44
RIGHT 1 ~ 45
OFF: HLC MASK
OFF
D-WDR
SET LEVEL
0 ~ 20
3D-DNR
OFF, LOW, MID, HIGH, AUTO
Reduce noise in low
light environments
WHITE BALANCE
AWB
ATW
Color temp. 2500 ~ 9500 K
MODE
MANUAL
M-WR
0 ~ 128: Adjust the
red value
M-WB
0 ~ 128: Adjust the
blue value
PUSH
Optimize white balance for current condi-
tions
R-Y GAIN
0 ~ 255
Adjust red tone of image
B-Y GAIN
0 ~ 255
Adjust blue tone of image
DAY & NIGHT
D&N
AUTO
DAY-NIGHT
7 ~ 30
MODE
NIGHT-DAY
6 ~ 29
DELAY TIME
0 ~ 15: Set the
duration
AUTO-
A. DAY-NIGHT
6 ~ 36
CDS
A. NIGHT-DAY
6 ~ 36
C. DAY-NIGHT
0 ~ 255
C. NIGHT-DAY
0 ~ 255
COLOR
Fixed at Color
B&W
Fixed at B&W
EXT
DELAY TIME
0 ~ 15
BURST
ON, OFF
Enable/disable burst
signal in BW mode
C-SUP
0 ~ 100
Color suppress
control
A-SUP
0 ~ 100
Iris suppress control
SMART
ON, OFF
Decreases screen
IR
saturation of objects
within a short range
MIRROR
MIRROR, OFF
Vertical image
inversion
SHARP-
0 ~ 30
NESS
GAMMA
0.45, 0.55, 0.65
USER
GAMMA
.20 ~ 1.00 by incre-
ments of .05
PRIVACY
MASK
OFF
1 ~ 8
ON
DOT SEL
L_TOP, L_BOT,
R_BOT, R_TOP:
Determines location
for Motion Detection
DOT XY
ENTER SETTING:
Determines coor-
dinates
MOVE XY
ENTER SETTING:
Determines coor-
dinates
COLOR
Select mask color
SPECIAL
LANGUAGE
Select language (9
available)
TITLE
OFF-ON
EDIT
Display the camera
name on screen
RESET
Camera name reset
POSITION
Camera name
position
DPC
OFF
Deactivates Detect
Pixel Correction in
low illumination
AUTO
WHITE THR
0 ~ 255: Set the
limited value of white
pixel correction
LUMA THR
0 ~ 255: Set the
limited value of white
pixel correction
RETURN
Move back to previ-
ous menu.
FACTORY SET
YES, NO
Reset your camera
to factory default
conditon
EXIT
SAVE AND EXIT
Save the value and
exit the menu
EXIT
Escape the menu
without saving
FUNCTION SETTING
1.
Push the lever to access the menu and confirm selec-
tion. Push the lever for one second to open or close the
menu. Use the lever to return to the previous menu from
motion detection or privacy mask setting sections.
2.
Use a screwdriver to adjust the focus.
3.
Use a screwdriver to adjust the zoom.
4.
Plug a test monitor into the optional VIDEO terminal to
view menu screens during installation.
5.
The debug port is used for product upgrades. This
should only be accessed by a trained technician.
Advertisement
