Table of Contents
Advertisement
Quick Links
Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks
CR9000
Stand-alone Touchscreen Access Lock
Installation and Programming Instructions
.
Take the time to read through this guide to familiarize yourself with the features and
operation of the lock, and its quick and easy programming procedures.
Save this PROGRAMMING INSTRUCTIONS for future reference
■ Note: Improper installations may result in damage to the lock and void the factory warranty.
Advertisement
Chapters
Table of Contents
Troubleshooting
Related Manuals for Cal-Royal CR9000
Summary of Contents for Cal-Royal CR9000
- Page 1 Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks CR9000 Stand-alone Touchscreen Access Lock Installation and Programming Instructions Take the time to read through this guide to familiarize yourself with the features and operation of the lock, and its quick and easy programming procedures.
-
Page 3: Table Of Contents
Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks INSTALLATION GUIDE TABLE OF CONTENTS Warnings ····················································································································································· 2 Introduction ················································································································································· 2 Specifications ············································································································································· 3 Parts Breakdown ·································································································································· 3~4 Tools for Installation ································································································································ 4 Installation Instructions Verify Hand and Bevel of Door ······································································································ 5 Door &... -
Page 4: Specifications
Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks SPECIFICATIONS § Latch brass - 1/2"(13㎜) throw standard § Inside lever retracts latch § Deadlocking latch § Locks furnished for 1-3/8"(35㎜) to § Outside lever controlled by touchpad or 2-3/4"(45㎜) doors. §... -
Page 5: Tools For Installation
Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks PARTS BREAKDOWN (Continued) ITEM DESCRIPTION QTY. Latch (2-3/4"(70㎜) Backset standard or 2-3/8"(60㎜) optional Outside Assembly Inside Escutcheon Inside Lever Spacer Bushing Battery Cover Mounting Plate Outside Lever Key (Provided with Cylinder) Cylinder Cylinder Retainer Lock Body... -
Page 6: Installation Instructions
Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks INSTALLATION INSTRUCTIONS Step #1 Verify Hand and Bevel of Door Stand on outside/locked side of the door when determining the door hand. Note: This lock is non-handed and the lever can be flipped around to the desirable hand. Left Hand Left Hand Right Hand... - Page 7 Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks Position Template and Mark Drill Points Be sure to verify backset before marking and drilling door. 1. Fold and Place template on high edge of door at the horizontal centerline. 2. Mark centers of holes at proper backset. For beveled and square edge doors, mark both sides of the door.
-
Page 8: Prepare Lock For Installation
Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks Step #3 Prepare Lock for Installation A. Unpack the Lock The lock is packed in such a way to represent how it will install on the door. Before installation: 1. Disassemble the inside escutcheon. 1) Remove the inside lever and spacer bushing with the lever removal tool provided. - Page 9 Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks Adjustment for different door thickness: 1. Remove outside lever, spacer bushing and outside assembly (See C below). 2. Rotate outside mounting rose plate for proper door thickness as shown below. 3. Position of bent taps as shown below must match (ensure the bent taps are horizontally crossed).
-
Page 10: Lock Installation
Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks Step #4 Lock Installation Outside Assembly Inside Assembly - 9 -... - Page 11 Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks PROCEDURES 1. Install latch in door. Be sure that bevel edge of bolt faces strike. Attach with two screws supplied. 2. Install strike on the door frame. 3. Insert outside assembly through door, making sure that the lock body frame hooks latch case and retractor engages bolt tail(s).
-
Page 12: Test Lock Operation
Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks Step #5 Test Lock Operation If you encounter problems while performing any of the following tests, review the in- stallation instructions and this guide and correct any problems. CAUTION : DOOR MUST REMAIN OPEN DURING INSTALLATION. USE DOOR STOP. Mechanical Test A. -
Page 13: Overview
Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks PROGRAMMING GUIDE Take the time to read through this guide to familiarize yourself with the features and oper ation of the lock, and its quick and easy programming procedures. TABLE OF CONTENTS Overview ···················································································································································... -
Page 14: Operation Of Lock
Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks OPERATION OF LOCK Opening the door with a PIN Code Touch screen with Enter a registered PIN Code and Turn lever to open door. back of hand or press [✱] button. fingers to activate. - Page 15 Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks Factory Defaults Settings Factory Defaults Master PIN Code 123456 Lockout Mode Unprogrammed Passage Mode Unprogrammed Re-lock Time 5 seconds Wrong Code Entry Limit 5 times Shut Down Time 60 seconds Beep Sound Scope of Master, User Settings Settings Master...
-
Page 16: Programming Features
Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks PROGRAMMING FEATURES Outside Inside Menu and Icons Symbols Description Touch screen with back of hand or fingers to activate. Press the indicated number buttons. ～ ✱ Press the [✱] button. It is used to complete an input process. Press the the [#] button. - Page 17 Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks To Begin Programming: The Lock is preset at the factory with Master PIN Code [123456]. Touch screen with back of hand or fingers to activate. 1 2 3 4 5 6 ✱ B.
- Page 18 Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks Register One-Time User PIN Code Enter è Mstr è è è è ✱ One-Time Setting Up/Releasing Passage Mode Mstr ✱ è è è Enable è ✱ Disable Enter ✱ è è è...
-
Page 19: Programming
Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks PROGRAMMING Change Default Master Code Before Programming Note: The factory default Master Code must be changed prior to adding users. Mstr Mstr Mstr ✱ è è è è è Default Enter New Enter New Touch screen with back of hand or fingers to activate. - Page 20 Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks 4. Press the button. Beep melody and Number pad blink one time. F [Repeat steps 3 and 4 for each new user (if necessary).] ✱ 5. Press the button. Completes with beep sound. [For example, John Smith and Jessica are users.
- Page 21 Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks 1. Enter the Master PIN Code and press the button. Green and Red LED blinks. 2. Enter the Program Code and press the button. Green and Red LED blinks. 3. Enter the One-Time User PIN Code and press the button.
- Page 22 Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks Green and Red LED blinks. ✱ 4. Press the button again. Completes with beep sound. Setting Up/Releasing Lockout Mode Mstr ✱ è è è Enable ✱ è Disable Touch screen with back of hand or fingers to activate. 1.
-
Page 23: Miscellaneous Information
Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks 1 2 # seconds, èplace the second card in front of the touchscreen (hear beep ✱ è melody and Number pad blink one time) Delete RF Card Enter the Card è Mstr è... -
Page 24: Glossary
Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks Battery Replacement When battery power is low, the low battery icon will begin blinking with beep sound. Always replace weak batteries as soon as possible. The locks use four (4) AA-size 1.5 volt alkaline batteries. -
Page 25: Troubleshooting
Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks TROUBLESHOOTING Symptom Suggested Action Ÿ Check if the batteries are faulty or in the correct polarity. There is no power. Ÿ Check if the batteries are inserted properly or completely discharged. Ÿ... - Page 26 Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks USER CODE RECORD SHEET User User User PIN Code RF Card Number Name (4~6 digits) registered No. ※ We recommend placing this record sheet in a safe and secure place. - 25 -...
-
Page 27: User Pin Code Record Sheet
Installation and Programming Instructions for Electronic Stand-Alone Cylindrical Locks Template for Door Prep. - 26 -...