Siruba Sew Reach D007S Instruction Book page 6

(4) 起初開始運轉針車的時候，需要確認
針車飛輪的旋轉方向，和飛輪的迴轉
標示是否一致。
2-5 針車運轉中的注意事項
(1) 務必在裝妥馬達蓋、護指、護目等的
安全保護狀態下運轉針車。
(2) 針車運轉中，在車針下方附近以及有
動作的機械部位附近，勿使手、頭髮
接近，更不可把物品放置在旁。
(3) 附有切刀裝置的針車，在針車運轉中
絕不可把手指伸入切刀部位。
(4) 在不使用針車或作業人員離開針車時，
務必關閉電源。
(5) 在使用中發現錯誤動作、異常的聲音
或異味的時候，應即刻關閉電源。
2-6 拆卸
(1) 拆卸任何零件或更換的時候，以及進
行調整作業的時候，務必先關閉電源。
(2) 要拔掉插頭的時候，不可直接拉扯電
線、電纜。
(3) 控制箱內配有高壓負荷，所以在關閉
電源之後要等待 5 分鐘以上才可以開
蓋。
2-7 保全、檢查與維修
(1) 保全、檢查修理作業的時候，應依照
使用說明書來作業。
(2) 執行保全、檢查及維修的作業，應由
經過特別訓練的人員來操作。
(3) 在執行保全、檢查及維修的作業時，
務必先關閉電源，在確認針車與馬達
完全停止的時候才開始作業。
(4) 請客戶勿根據獨自判斷來自行改造針
車。
(5) 避免用指定以外的保全維修零件。
P3
(4)When start to operate the sewing
machine at first, make sure the rotating
direction of pulley tallies with rotating-
direction mark.
2-5 Instructions while operating
(1)Be sure to operate the sewing machine
with the safeguards such as motor
cover, finger guard, and eyes guard,
etc.
(2)During operation, do not let your hands
or hair near the machine; moreover, put
an object beside under the needle or
near the moving parts of machine.
(3)Never puts your hand close to the
knives part during operation which
sewing machine has trimming device.
(4)Must turn off the power without
operators or using the sewing machine.
(5)If the machine malfunctions, make
abnormal sound or smelling unusual,
turn off power immediately.
2-6 Removal
(1)Must turn off power first if disassembling
or removing any parts, or doing
adjustment.
(2)To pull the plug, do not pull or drag its
cable or wire.
(3)A high voltage is applied inside the
control box, do not open the cover until
wait for five minutes.
2-7 Maintenance, inspection, and repair
(1)Follow the instruction manual to do
maintenance, inspection, and repair.
(2)Entrust the specially trained workers to
do maintenance, inspection, and repair.
(3)Must turn off the power first and make
sure the motor and sewing machine
are completely stop, then do the
maintenance, inspection, and repair
work.
(4)Do not transform the sewing machine
by customer judgment.
's
(5)Use original parts for maintenance and
repair.