Siruba Sew Reach D007S Instruction Book page 34

7. 壓腳
拆除方法：
(1) 移開前蓋①和所有的針。
(2) 放鬆調整螺帽②然後才鬆開螺絲③。
(3) 鬆開刀台的螺絲④讓整組刀架鬆開。
(4) 鬆開刀座連桿⑥的兩螺絲⑦，移除上刀座
⑤和上刀。
(5) 放鬆壓腳螺絲⑧。
(6) 將針轉到最高點，然後移除調整螺帽②和
抽出壓腳柱⑨和壓腳彈簧⑩。
(7) 推開上勾針驅動片 從帶動桿 脫離。
(8) 向左轉，拆下整組壓腳穿過左邊壓腳檔
。
組裝方法：
(1) 拆掉全部的針重新裝上壓腳在左右壓腳檔
之間，向右旋轉，放正壓腳。
(2) 重新裝上上勾針驅動片 到帶動桿 裡
面。
(3) 安裝壓腳柱插入上勾針驅動片 後鎖上壓
腳後面的螺絲⑧。
(4) 檢查壓腳是否順暢沒有左右晃動，如果有
卡住，鬆開左壓腳檔 的螺絲 去調整。
(5) 重新裝上刀台⑤固定在刀座⑥支撐架上。
(6) 調整刀台和上刀的位置，當針在最低點的
時候。
(7) 當壓腳緊貼在針上和針在最低點時，重新
裝上壓腳彈簧⑩及調整螺帽②，然後輕
輕的壓下螺絲③並鎖上。
(8) 鎖上外蓋①並裝回所有的針。
P31
7.Presser foot
Way to remove：
(1) Remove cover ① and all of the needles.
(2) Loosen screw nut ②, then loosen screw
③.
(3) Loosen screw ④ of knife holder, to free
the complete of knife set.
(4) Loosen two screws ⑦ from knife holder
bracket ⑥, remove upper knife ⑤ and
upper knife.
(5) Loosen presser foot screw ⑧.
(6) Turn the needle to the highest point, then
remove adjusting screw nut ② and take
off presser foot bar ⑨ and presser foot
spring ⑩.
(7) Remove upper looper driving segment
from lever .
(8) Turn it left, and remove the whole set of
presser foot through the left presser foot
guide .
Way of assembling：
(1) Remove all of the needles and reset the
presser foot in the middle of the left and
right presser foot guard. Turn it right and
put the right presser foot.
(2) Reset the upper looper driving segment
inside to the lever
(3) Insert the presser foot bar into the upper
looper driving segment
the screw ⑧ behind the presser foot.
(4) Check whether presser foot move
smoothly without shaking, if it stuck,
loosen screw of left presser foot guard
to adjust.
(5) Reset the knife holder ⑤ and fixed on the
knife holder bracket ⑥.
(6) Adjust position of knife holder and upper
knife, while the needle at the lowest point.
(7) When the needle is at the lowest point
and the presser foot closely touch the
needle, reset the presser foot spring ⑩
and adjust the screw nut ②, then slightly
presser the screw ③ and tighten it.
(8) Reset the cover ① and all of the needles.
.
, then tighten