En Compliance; European Ce Compliance Statement; Uk Compliance Statement - Johnson Controls Tyco PowerSeries Pro User Manual

FCC AND ISED CANADA FOR WIRELESS KEYPADS
WARNING! To comply with FCC and ISED Canada RF exposure compliance requirements, the HS2LCDRF(P)9 or HS2LCDWF(P)9 keypads should be located at
a distance of at least 20 cm from all persons during normal operation. The antennas used for this product must not be co-located or operated in conjunction with any
other antenna or transmitter. This device complies with FCC Rules Part 15 and with ISED Canada license-exempt RSS standard(s). Operation is subject to the fol-
lowing two conditions: (1) This device may not cause harmful interference, and (2)this device must accept any interference that may be received or that may cause
undesired operation.
ISED:160A – HS2KRFP9
Models: HS2LCDRF9, HS2LCDRFP9, HS2LCDWF9, HS2LCDWFP9 (operating in 912-919MHz band) are compliant with applicable FCC Part 15.247 and IC
RSS-210 rules.
The term "ISED" before the radio certification number only signifies that ISED Canada technical specifications were met.
AVERTISSEMENT! Pour répondre aux exigences de conformité de la FCC et ISDE Canada sur les limites d'exposition aux radiofréquences (RF), les clavier
HS2LCDRF(P)9 ou HS2LCDWF(P)9 doivent être installés à une distance minimale de 20 cm de toute personne lors de leur fonctionnement usuel. Ces derniers ne
doivent pas être situés au même endroit, ni être en fonction avec une autre antenne ou un autre transmetteur. Le present appareil est conforme aux CNR ISDE
Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes: (1)l'appareil ne doit pas produire de brouillage,
et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement.

14.1 EN Compliance

This product meets the requirements of Class II, Grade 3 equipment as per EN 50131-1:2006 + A1:2009 +A2:2017 Standard. This product is suitable for use in sys-
tems with the following notification options:
- A (use of two remotely powered warning devices and single path SP3 internal dialer or Ethernet path or plug-in cellular module required),
- B (self powered warning device (wireless siren) and single path SP3 internal dialer or Ethernet path or plug-in cellular module required),
- C (dual path DP2 internal dialer and alternate Ethernet or plug-in cellular communicator required)
- D (single path SP4 internal Ethernet path or plug-in cellular communicator with encryption enabled required)
- E (dual path DP3 internal Ethernet path and plug-in cellular communicator required)
The Model HS3032, HS3128 Control Panel has been certified by Telefication according to EN50131-1:2006 + A1:2009 +A2:2017, EN50131-3:2009 Type B,
EN50131-6:2017 Type A, EN50131-10:2014 and EN50136-2:2013 for Grade 3, Class II, ATS Configurations SP3 (phone line path only), SP4 (Ethernet or cellular
path only), DP2 (dual path with phone line primary path and Ethernet or Cellular secondary path) and DP3 (dual path with Ethernet or Cell primary path and Cellular
or Ethernet as secondary path.

14.2 EUROPEAN CE COMPLIANCE STATEMENT

This product is in conformity with the Electromagnetic Compatibility Directive 2014/30/EU, the Low Voltage Directive 2014/35/EU, and the ROHS2 Directive
2011/65/EU.
SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, Tyco Safety Products Canada Ltd declares that the radio equipment type is in compliance with Directive 2014/53/EU. The full text of the EU declarations
of conformity for the models mentioned below are available at the following internet addresses:
HS2LCDRF(P)(V)4: http://dsc.com/pdf/1401057
HS2LCDRF(P)(V)8: http://dsc.com/pdf/1401058
HS2LCDWF(P)(V)4: http://dsc.com/pdf/1401061
HS2LCDWF(P)(V)8: http://dsc.com/pdf/1401062
Frequency Band / Maximum Power
g1 433.04MHz – 434.79MHz/10mW
h1.4 868.0MHz – 868.6MHz/10mW
h1.5 868.7MHz – 869.2MHz/10mW
a3 119MHz – 135MHz - 66 dbµA/m @10m
European single point of contact: Tyco Safety Products, Voltaweg 20, 6101 XK Echt, Netherlands

14.3 UK Compliance Statement

In the UK this product is suitable for use in systems installed to conform to PD 6662:2017 at Grade 3 and environmental class II with
the following notification options: A, B, C, D, E.
Where HS3032, HS3128 are used with a single path signaling method (such as the Integrated Digital Dialer), please note the fol-
lowing limitation:
IMPORTANT
Your attention is drawn to the fact that failure or compromise of single path signaling cannot be passed to the police. While the failure
persists, subsequent alarms cannot be notified to the alarm receiving centre and passed to the police.
Setting Methods
The HS3032, HS3128 is capable to support the completion of the full setting procedure by the following methods:
a) push button switch, mounted outside the supervised premises; or b) protective switch (i.e., door contact) fitted to the final exit door
of the alarmed premises or area. The setting procedure is a two-stage process of initiating the setting procedure within the super-
vised premises (e.g., using Mini Prox Tag (MPT) or user code) followed by completion of setting by one of the two methods men-
tioned above. Please check with the Installer which method has been enabled for your system.
Unsetting Methods
The HS3032, HS3128 is capable to support the following unsetting methods in accordance with BS8243:
6.4.2 Prevention of entry to the supervised premises before the alarm system is unset. Unsetting using remote key before entering
the supervised premises causes or permits the initial entry door to be unlocked.