Page 1 PowerSeries Pro Reference Manual HS3032 / HS3128 / HS3248 This manual contains information on limitations regarding product use, function and information on the limitations as to liability of the manufacturer. Carefully read the entire manual.
Page 2: Table Of Contents
Contents 1.0 Safety instructions Section 1: Introduction 1.1 About the system Section 2: Installation 2.1 Before installing the equipment 2.2 Overview of installation process 2.3 Alarm controller installation 2.4 General wiring instructions 2.5 Installing modules Section 4: Configuration 4.1 Basic configuration steps 4.2 Using the keypad 4.3 Enrollment 4.4 Working with partitions...
Page 3 7.22 Module Programming 7.23 Wireless Placement Testing 7.24 Battery Settings 7.25 Restoring Factory Defaults Section 8: Troubleshooting 8.1 Testing 8.2 Troubleshooting Appendix 1: Reporting codes 1.1 Contact ID 1.2 SIA Format - Level 2 (Hard Coded) 1.3 Contact ID & SIA Zone Alarm/Restore Event Codes Appendix 2: Word library Appendix 3: Template programming tables 3.1 Digit 1 –...
Page 4: Safety Instructions
1.0 Safety instructions Read the safety information before you install the equipment. Important: This equipment must be installed by a skilled person only. A skilled person is an installer with appropriate technical training. The installer must be aware of potential hazards during installation and measures available to minimize risks to the installer and other people.
Page 5: Section 1: Introduction
Section 1: Introduction Section 1: Introduction 1.1 About the system The PowerSeries Pro alarm panel is a feature-rich, scalable alarm system designed for commercial use. The alarm panel supports both hardwired and wireless devices. This section lists the features of the alarm panel, available models, and compatible devices. The following symbols are used to indicate features or methods of operation that are only available in a particular market.
Page 6 Section 1: Introduction Available models The following alarm controller models are available: HS3032 HS3128 HS3248 Model comparison The table below lists the features of each alarm system model. Table 1-1: Model comparison Features HS3032 HS3128 HS3248 On board Zones PGMs 2-way audio interface Cellular plug-in interface On-board ethernet connection...
Page 7 Section 1: Introduction Features HS3032 HS3128 HS3248 LCD Keypad with Prox - HS2LCDPRO Touchscreen with Prox - HS2TCHPRO(BLK) Wire-free Keypad with Prox - HS2LCDWFPROx Wire-free Keypad Prox and Voice - HS2LCDWFVPROx * For UL installations, 2 wireless repeaters must be installed for proper signal routing. ** Only one PowerG transceiver can be enrolled on a PowerSeries Pro panel.
Page 8 Section 1: Introduction Compatible devices The following wireless devices and modules are compatible with this alarm controller. In the table below and throughout this document, x in the model number represents the operating frequency of the device as follows: 9 (912-919 MHz), 8 (868MHz), 4 (433MHz).
Page 9 Section 1: Introduction PG9934(P) PG8934(P) PGx934(P) PIR motion detector with camera PG9944 PG8944 PGx944 Outdoor PIR motion detector with camera and anti-masking PG9974(P) PG8974(P) PGx974(P) Mirror optic PIR motion detector PG9984(P) PG8984(P) PGx984(P) Dual technology (PIR and MW) with anti-masking PG9994 PG8994 PGx994 Outdoor PIR motion detector with anti-masking...
Page 10 Section 1: Introduction 2-wire smoke detector: x = A, B, or C FSA-210x FSA-210xT A = ULC listed models FSA-210xS B = UL listed models FSA-210xST C = European and Australian models FSA-210xLST L = Remote LED output FSA-210xR R = Auxiliary form C relay FSA-210xRT S = Sounder FSA-210xRS...
Page 11: Section 2: Installation
Section 2: Installation Section 2: Installation 2.1 Before installing the equipment Ensure your package includes the following items: Installation and user guides HS3032/HS3128/HS3248 alarm controller Power supply Select a location that is within an environment that provides a pollution degree max 2, over voltages category II. non-hazardous, indoor locations only.
Page 12 Section 2: Installation Mounting the enclosure This section provides basic instructions for wall-mounting the available PowerSeries Pro enclosures. Mount in a dry location, near an unswitched AC power source and Ethernet and phone connections. Note: Complete all wiring before applying AC or connecting the battery. Note: The weight of the enclosure and contents cannot be supported by drywall only.
Page 13 Section 2: Installation Wall mounting HSC3010C/ HSC3010CR/ HSC3030CAR enclosures The following diagram indicates the mounting location of the alarm controller PCB, power supply module and tamper bracket inside HSC3010C/ HSC3010CR/ HSC3030CAR enclosures. Figure 2-2: HSC3010C, HSC3010CR, HSC3030CAR enclosures Callout Description Metal standoff Tamper mounting location Alarm controller PCB location...
Page 14 Section 2: Installation Wall mounting the HSC3020C enclosure The following diagram indicates the mounting location of the alarm controller PCB, power supply module and tamper bracket inside the HSC3020C enclosure. Figure 2-3: HSC3020C enclosure Callout Description Tamper mounting location Alarm controller PCB location Power supply module location Note: Before mounting the metal enclosure, ensure that the enclosure ground wire has been installed (refer to instructions in this manual).
Page 15 Section 2: Installation Wall mounting the HSC3020CP enclosure (EU only) The following diagram indicates the mounting location of the alarm controller PCB, wireless receiver, power supply module and tamper bracket inside the HSC3020CP enclosure. Figure 2-4: HSC3020CP enclosure Callout Description Tamper screws Wireless receiver module Alarm controller PCB Power supply module...
Page 16 Section 2: Installation HSM3204CX/HSM3350 mounting location in HSC3010C The following diagram indicates the mounting location of the HSM3204CX/HSM3350, power supply module and tamper bracket inside the HSC3010C/ HSC3010CR/ HSC3030CAR and HSC3020 enclosures. Figure 2-5: HSM3204CX/HSM3350 mounted in HSC3010C, HSC3010CR, HSC3030CAR enclosures Callout Description Alarm controller PCB...
Page 17 Section 2: Installation HSM3408 and HSM3350 mounting in HSC3020C enclosure The following diagram indicates the available mounting locations of the HSM3350, HSM3408 and power supply module inside the HSC3020C. Figure 2-7: HSM3408 and HSM3350 modules in HSC3020C enclosure HSM3350 HSM3408 HSM3408 HSM2108/HSM2208 mounting locations in HSC3010 enclosure The following diagram indicates all available mounting locations of the HSM2108/HSM2208 inside HSC3010C/ HSC3010CR/...
Page 18: General Wiring Instructions
Section 2: Installation 2.4 General wiring instructions Warning: Disconnect AC power before servicing. To connect the wiring for the PowerSeries Pro, complete the following steps: 1. Insert thestandoffs into the cabinet mounting holes in the desired location. Snap into place. 2. Position circuit board over the standoffs. Press firmly on board to snap into place. 3.
Page 19 Section 2: Installation HS3032/HS3128/HS3248 in HSC3010C NA wiring diagram This diagram shows the routing of power limited and non-power limited wiring inside the enclosure. The battery leads and AC cord are non-power limited, all other wiring is power limited. Figure 2-9: Panel wiring for HSC3010C PC LINK MICRO-B USB TYPE A...
Page 20 Section 2: Installation Power supply Primary: 120 VAC, 60 Hz, Class VI; Secondary: 18 VDC, 3.6 A Power supply adapter module: HS65WPSNA Note: Do not connect the power adapter module to receptacle controlled by a switch. - 20 -...
Page 21 Section 2: Installation HS3032/HS3128/HS3248 in HSC3010C wiring diagram (Argentina only) This diagram indicates the installation of components in the HSC3010C enclosure. Figure 2-10: HS3032/HS3128/HS3248 in HSC3010C wiring (Argentina) 18009689R001 Callout Description Earth ground connection. Wire to the power adapter EGND connection when this power adapter is mounted in the cabinet. Enclosure Star washer Bolt...
Page 22 Section 2: Installation HS3032/HS3128/HS3248 in HSC3020C NA wiring diagram This diagram shows routing of power limited and non-power limited wiring inside the enclosure. Battery leads and AC cord are non- power limited. All other wiring is power limited. Figure 2-11: Panel wiring for HSC3020C (for North America) PC LINK MICRO-B USB TYPE A...
Page 23 Section 2: Installation Mounting the HSC3020C 1. If mounting the power supply inside the cabinet, attach it as per Figure 2-9 using supplied hardware. Note: Minimum 1/4-inch (6.4 mm) separation must be maintained at all points between battery/AC wiring and all other wiring connections.
Page 24 Section 2: Installation HSM3204CX in HSC3020C North American wiring diagram This diagram shows routing of power limited and non-power limited wiring inside the enclosure. Battery leads and AC cord are non- power limited. All other wiring is power limited. Figure 2-13: North American wiring for HSM3204CX in HSC3020C enclosure Callout Description Power limited entry/exit points...
Page 25 Section 2: Installation Installing the HSM3350 in the HSC3010C enclosure The following diagram indicates the routing of power limited and non-power limited wiring inside the enclosure. Battery leads and AC cord are non-power limited. All other wiring is power limited. Figure 2-14: HSM3350 in HSC3010C enclosure Callout Description...
Page 26 Section 2: Installation North American wiring for HSM3350 in the HSC3020C enclosure This diagram shows routing of power limited and non-power limited wiring inside the enclosure. Battery leads and AC cord are non- power limited. All other wiring is power limited. Figure 2-15: North American wiring for HSM3350 in the HSC3020C enclosure Callout Description...
Page 27 Section 2: Installation Installing the HS3032/HS3128/HS3248 in the HSC3020C enclosure (EU models) Figure 2-16: Panel wiring for HSC3020C (EU) enclosure PC LINK MICRO-B USB TYPE A UA718 BATTERY Callout Description Power limited wiring entry/exit point Tamper switch and mounting bracket HS3032/HS3128/HS3248.
Page 28 Section 2: Installation Warning: Incorrect connections may result in PTC failure or improper operation. Inspect wiring and ensure connections are correct before applying power. EN installation notes Warning: High voltage: Disconnect AC power and telephone lines before servicing. 1. The connection to the mains supply must be made as per the local authorities’ rules and regulations: In the UK as per BS6701. An appropriate disconnect device must be provided as part of the building installation.
Page 29 Section 2: Installation Installing and wiring in the HSC3020CP The HSC3020CP enclosure ships with the PCB assembly, HS65WPS power adapter, fuse block and tamper switch, to be installed as shown inFigure 2-17. The cellular communicator (if provided), case tamper switch, battery, and AC must be wired as shown in Figure 2-17 and Figure 2-18.
Page 30 Section 2: Installation Figure 2-18: HSC3020CP wiring PC LINK MICRO-B USB TYPE A UA718 BATTERY Callout Description HSM2HOST8 tranceiver module Antenna ports Cellular communicator attachment points (use supplied screws) Expansion module slots (x2) Power adapter ground wire Fuse (replace the fuse with the same type; 20 mm, rated 250 V/3.15A slow blow) To power adapter (blue - neutral) To power adapter (green/yellow - EGND) To power adapter (brown - live)
Page 31 Section 2: Installation HSM3204CX in HSC3020C wiring diagram (EU) This diagram shows routing of power limited and non-power limited wiring inside the enclosure. Battery leads and AC cord are non- power limited. All other wiring is power limited. Figure 2-19: HSM3204CX wiring for HSC3020C enclosure Callout Description Power limited wiring entry/exit point...
Page 32 Section 2: Installation HSM3350 in HSC3020C wiring diagram (EU) The HSM3350 is a supervised 3 A, 12 VDC power supply module with dual AUX outputs and dual battery backups. The 4-wire Corbus connection provides communication between the module and alarm panel. Connect the RED, BLK, YEL and GRN terminals to the Corbus terminals on the alarm controller.
Page 33 Section 2: Installation Terminal descriptions The following terminals are available on the PowerSeries Pro alarm controller. Table 2-1: Terminal descriptions Terminal Description BAT+, BAT- Battery terminals. Use to provide backup power during a power outage and additional current when system demands exceed the power output of power adapter.
Page 34 Section 2: Installation Module (A) is wired correctly as it is within 1000 ft / 305 m of the panel, in wire distance. Module (B) is wired correctly as it is within 1000 ft / 305 m of the panel, in wire distance. Module (C) is NOT wired correctly as it is farther than 1000 ft / 305 m from the panel. For models that require more than 1000 ft / 305 m from the main panel, a HSM3204CX power supply/Corbus extender can be used.
Page 35 Section 2: Installation Overcurrent trouble If the total current of the panel internal components and all outputs exceeds a threshold of 2.1 A for a period longer than 5 minutes, an overcurrent trouble is generated. When the current goes below a 2.0 A threshold, the trouble restores. Do not exceed 2.0 A combined between AUX and Corbus.
Page 36: Installing Modules
Section 2: Installation 2.5 Installing modules Remove all power from the system while connecting modules to the alarm controller. Zone expanders The main alarm controller has connection terminals for zones 1 to 8. Additional HSM2108 and HSM3408 zone expanders may be added to increase the number of zones on the system.
Page 37 Section 2: Installation Output expander The HSM2208 module is used to add up to 8 low-current programmable outputs to the alarm system. The 4-wire Corbus connection is used by the panel to communicate with the module. Connect the RED, BLK, YEL and GRN terminals to the Corbus terminals on the alarm panel.
Page 38 Section 2: Installation Power supply wiring HSM2300/2204 The HSM2300/2204 power supply/high-current output module provides up to 1 A of additional current and can be used to add up to four programmable outputs (HSM2204 only) to the alarm system. The 4-wire Corbus connection provides communication between the module and alarm panel. Connect the RED, BLK, YEL and GRN terminals to the Corbus terminals on the alarm controller.
Page 39 Section 2: Installation HSM3350 The HSM3350 is a supervised 3 A, 12 VDC power supply module with dual AUX outputs and dual battery backups. The 4-wire Corbus connection provides communication between the module and alarm panel. Connect the RED, BLK, YEL and GRN terminals to the Corbus terminals on the alarm controller.
Page 40 Section 2: Installation Callout Component Description AUX 1 10.8 VDC to 12.5 VDC, 3 A max. (UL/ULC applications). Note: Aux output shared with Corbus. AUX2 10 VDC to 14 VDC, 3 A max. supervised (EN50131 applications) Fuse For EU models only; 20 mm, rated 250V / 3.15A slow blow; replace the fuse with the same type. Note: All circuits are classified for UL installations as power limited/Class II power limited, except for the battery leads which are not power limited.
Page 41 Section 2: Installation Figure 2-29: HSM3204CX Corbus repeater Status LED UA721 +BAT- CORBUS OUT RLY1 RLY2 RLY3 RLY4 CORBUS IN YEL GRN Callout Component Description Battery 1 12 VDC minimum 4/7/17 Ah Battery 2 12 VDC minimum 7 Ah Power Primary input 120 VAC, 60 Hz, 1.7 A, cord connected (UL/ULC applications).
Page 42 Section 2: Installation Keypad zones support Normally Closed Loops, Single End of Line, Double End of Line, and Triple End of Line resistors. To connect the PGM output, run one wire to the P/Z terminal and the other to R. Figure 2-30: Keypad terminals Callout Description...
Page 43 Section 2: Installation Wire gauge Maximum length to EOL resistor (ft/meters) 6200 / 1889 7800 / 2377 Figures are based on maximum wiring resistance of 100 Ω. Zone status-loop resistance/status Table 2-5: Loop resistance values Loop Status Loop Resistance SEOL (standard) SEOL (Fire) DEOL TEOL...
Page 44 Section 2: Installation Figure 2-32: SEOL wiring Callout Description Any Z terminal Any COM terminal Normally open contact 5600 Ω end of line resistor 2 normally open contacts 2 normally closed contacts Normally closed contact The following table shows zone status under certain conditions for SEOL: Table 2-7: SEOL loop status Loop resistance Loop status...
Page 45 Double end of line (DEOL) resistors When double end-of-line (DEOL) resistors are installed at the end of a zone loop, the second resistor enables the panel to determine if the zone is in open, closed, tampered or faulted. Note: Any zone programmed for Fire or 24-hr Supervisory must be wired with a SEOL resistor regardless of the type of zone wiring supervision selected for the panel.
Page 46 Triple end-of-line (TEOL) resistor The TEOL resistor supervises anti-masking functionality in hardwired motion detectors. To configure TEOL supervision per zone, use programming section [002], attribute 15. Figure 3-2: TEOL wiring Callout Description Any Z terminal Any COM terminal 5600 Ω end of line resistor Normally closed tamper contact Normally closed alarm contact 10000 Ω...
Page 47 PGM wiring Min/max operating voltages for devices, sensors and modules is 9.8 V DC - 14 V DC. PGMs switch to ground when activated from the alarm controller. Connect the positive side of the device to the AUX+ terminal and the negative side to a PGM terminal.
Page 48 Figure 3-4: Bell wiring BELL The Bell output is supervised and power limited by 2A hardware protection. If unused, connect a 1000 Ω resistor across Bell+ and Bell- to prevent the panel from displaying a trouble. See "Troubleshooting" on page 68. Note: Observe polarity when connecting polarized sirens or bells.
Page 49 Smoke detector wiring All zones defined as Fire must be wired according to the following diagram: Figure 3-6: Smoke detector wiring 1 PGM 2 + AUX - RM-2 ZONE NO NC C Callout Component 5600 Ω end of line resistor To alarm initiating circuit See "[001] zone types"...
Page 50 Table 3-4: Compatible 2-wire smoke detectors 2-wire smoke detectors FSA-210x FSA-210xR FSA-210xT FSA-210xRT FSA-210xS FSA-210xRS FSA-210xST FSA-210xRST FSA-210xLST FSA-210xLRST Current ratings for DSC FSA-210B series: 35mA - 75mA Table 3-5: 2-wire smoke detector initiating circuit Item Specification Style/Class, Supervised, Power Limited Style B (Class B) Compatibility Identifier HS3-1...
Page 51 Note: For multiple unit connections, the leads between CO detectors must be broken. The power supervision relay must be powered from the last detector in the loop. Wireless CO detectors are also available. When installing wireless CO detectors, use only model PG9913 , PG8913, PG4913, or PGx933.
Page 52 Figure 3-10: Earth ground installation Callout Description Earth ground connection from building electrical installation. Note: This ground connection goes to HS65WPSNA power adapter EGND connections when this power adapter is mounted in the cabinet. Cabinet Star washer Bolt (insert from the rear side of the metal enclosure) Earth ground symbol Connecting power Batteries...
Page 53 Refer to "Regulatory approvals" on page 304. for detailed Aux. loading and battery charging information. Complete the following chart to find (A), complete the following formula to find the battery capacity (B) and refer to the HS3032/3128/HS3248 alarm controller battery selection chart above. (Total standby current ________ mA (A) x Standby time ________ hours) + (Alarm current x Alarm time ________ hours \ 1000) = __ _____ Ah (B) Aux loading and battery selection...
Page 54: Section 4: Configuration
Section 4: Configuration Section 4: Configuration 4.1 Basic configuration steps Once basic installation of the alarm panel is complete, the following general configuration options should be set. Create partitions, See "Working with partitions" on page 56. Assign keypads to partitions, see "Keypad partition setup " on page 57 Assign sirens to partitions, see "Bell/siren operation"...
Page 55: Enrollment
Section 4: Configuration Number of flashes Trouble type No keypads enrolled Module supervision trouble Bus low voltage Low battery trouble AC trouble Bell trouble TLM trouble Entering letters manually (system labels) 1. In Installer Programming, enter the section requiring text input. 2.
Page 56: Working With Partitions
Section 4: Configuration Module supervision By default, all modules are supervised upon installation. Supervision is enabled at all times so that the panel can indicate a trouble if a module is removed from the system. To check which modules are currently connected and supervised, see "[903] Confirm Module" on page 157. If a module is connected but is not recognized by the system, it may be due to any of the following reasons: the module is incorrectly wired to the alarm controller the module has exceeded its maximum wire run length...
Page 57: Trouble Indicators
Section 4: Configuration Bell/siren operation Each partition must have a siren. The system siren connected to the bell output of the alarm controller can be mounted in a central location within hearing range of all partitions. Each partition can also have wireless sirens activated only on the assigned partition. See "Wireless Programming"...
Page 58 Section 4: Configuration If the keypad is inactive for more than 30 seconds, it reverts to its assigned partition. Global zones If a zone is added to more than one partition, it becomes a global zone. A global zone is only armed when all assigned partitions are armed and is disarmed when any assigned partition is disarmed.
Page 59: Alternate Communicator Setup
Section 4: Configuration Zone Labels Partition Labels Module Labels Partition 1 to 32 Command Output 1 to 4 Labels Schedule 1 to 4 Labels Event Labels User Labels System and module programming is not affected. Hardware reset main control panel Perform the following to restore the main control panel to default settings: 1.
Page 60: Local Firmware Upgrade
Section 4: Configuration Remote firmware upgrade Firmware upgrades can be transferred to the alarm panel and modules using DLS. A message is displayed on LCD keypads indicating a firmware upgrade is available. On all keypads, the blue light bar flashes. Users authorize the firmware upgrade through [*][6][Master Code][17].
Page 61: Section 5: System Operation
Section 5: System operation Section 5: System operation 5.1 Arming and disarming The following table describes the various arming and disarming methods available. Table 5-1: Arming/disarming methods Method Description for 2 seconds + [Access Code*] Away Arm for 2 seconds + [Access Code*] Stay Arm Night Arm When armed in stay mode [*][1] + [Access Code*]...
Page 62: Labels
Section 5: System operation depending on system programming. Keypad function keys can be programmed for Global Stay Arm, Global Away Arm and Global Disarm. Multiple partition arming/disarming may be done from a global keypad, assigned to the same partitions as the user, by scrolling right and selecting "[*] to Arm All Partitions.
Page 63: Annunciation
Section 5: System operation 5.4 Annunciation Door chime The keypad can be programmed to use one of four different door chime tones for each zone on the system. Chime is active only during the disarm state. Only one door chime option can be enabled for each zone. Beeps Bing-Bong Ding-Dong...
Page 64 Section 5: System operation Note: Programmed function keys must be pressed for 2 seconds in order to activate the function. Function key definitions This section provides detailed descriptions of each programmable function key option. [00] Null function key This option deactivates the function key. The key does not perform any function when pressed. [02] Instant stay arm This feature is similar to the Stay Arm function key, except that no exit delay is applied and the system arms immediately.
Page 65 Section 5: System operation system is disarmed, pressing this key causes an error tone. An access code is not required to use this key. See "[015] System Option 3" on page 111 for more information. [17] Arm interior This key removes or enables automatic bypass on all Stay/Away zones (equivalent to pressing [*][1] while armed). If this function is performed while stay armed and, Night zones are programmed, the system arms in Night mode.
Page 66: Language Selection
Section 5: System operation 5.6 Language selection The keypad can be programmed to display messages and labels in different languages. Perform the following from the Installer Programming menu: 1. Enter installer programming [*][8][installer code] 2. Enter section [000]>[000]. 3. Select a language using the scroll buttons or by entering a hotkey: Table 5-3: Languages Option Language...
Page 67 Section 5: System operation To enable temperature reporting on wireless PowerG devices, section [804][810] option 5 must be on. A function key can also be programmed for this feature. See "[023] System Option 11" on page 118. [*][1] Bypass or stay/away/night zones The [*][1] command functions differently depending on whether the system is armed or disarmed.
Page 68 Section 5: System operation Shortcuts from the [*][1] base menu: Option Description Bypass group Program group 1 Bypass open zones Bypass recall Clear group When the alarm system is armed When the system is armed, pressing [*][1] toggles between stay, away or night arming. If a night zone is on the system, pressing [*][1] either prompts the user for an access code if required, or sounds an acknowledgment tone and changes the arming mode.
Page 69 Section 5: System operation Table 5-5: Trouble 02 Battery trouble Trouble Trouble description option [01] Panel low battery trouble: The battery voltage is low. [02] Panel no battery: No battery connected to alarm controller. [04] HSM2204 01 - 04 low battery: An HSM2204 has a low battery voltage. [05] HSM2204 01 - 04 no battery: No battery connected to HSM2204.
Page 70 Section 5: System operation Table 5-8: Trouble 05 Device faults Trouble Trouble description option [01] Zone 001 - 248: A zone is in supervisory fault. [02] Keypad 01 - 32: A wireless or hardwired keypad is in supervisory fault. [03] Siren 01 - 16: A siren is in supervisory fault.
Page 71 Section 5: System operation Trouble Trouble description option [02] Keypad 01 - 32 is not responding. [04] HSM2108 01 - 30 is not responding. [05] HSM2300 01 - 04 is not responding. [06] HSM2204 01 - 04 is not responding. [08] HSM2208 01 - 16 is not responding.
Page 72 Section 5: System operation Trouble Trouble description option [02] Keypad 01-32 Not Networked: Generated when a keypad becomes out of sync with the wireless network or has not been synchronized with the network after enrollment. [03] Siren 01-16 Not Networked: Generated when a siren becomes out of sync with the wireless network or has not been synchronized with the network after enrollment.
Page 73 Section 5: System operation Alarm tone Zone Name -Voice annunciation (HS2LCDWFVPROx keypads only) The above door chime sounds are programmable in section [861]-[892], subsections [101]-[228]. [*][5] Program access codes Use this section to perform the following functions: press [1] to program user codes 0002-1000, and master code 0001 press [2] to enroll a proximity tag press [3] to add a custom label for each user press [4] to assign users to partitions...
Page 74 Section 5: System operation The Maintenance code can be programed by the installer in programming section [006][003]. The default is AAAA (4-digit), AAAAAA (6-digit) or AAAAAAAA (8-digit). User Codes - Access Codes [0002] to [1000] This type of access code is used to arm and disarm assigned partitions and perform other functions as programmed. It can access the [*][6] menu if programming option [023] option 8 is on.
Page 75 Section 5: System operation 7 – Bell Squawk When this option is assigned, the main bell squawks when the alarm system is away armed. For example, use the arm/disarm bell squawk attribute to have wireless key access codes squawk the bell, while other codes are silent. To do this, enable this attribute on all access codes associated with wireless keys.
Page 76 Section 5: System operation 2. User code and proximity tag - the user must enter a valid code and present a proximity tag to access the system. The user code and proximity tag must match. For example, if the tag is associated with user 0004, user code 0004 must be entered after presenting the tag. ...
Page 77 Section 5: System operation Note: The Auto-arm Cancellation reporting code is also transmitted if arming is inhibited by one of the following: AC / DC Inhibit Arm Latching System Tampers Zone Expander Supervisory Fault Other programming options that may affect this function: See "[151]-[182] Partition Auto-Arm/Disarm"...
Page 78 Section 5: System operation This function is used to program the time of day the partition must be disarmed by when the Late to Open option is enabled. A separate time can be programmed for each day of the week. Valid data entries are 00:00 - 23:59. 99:99 disables the late to open feature for the selected day.
Page 79: Visual Verification
Section 5: System operation This option is used to activate or deactivate command outputs 1 to 4 for each partition and enable command outputs to follow a schedule. Using an LCD keypad 1. Press [*][7] to enter Output Control mode. 2.
Page 80 Section 5: System operation To set up visual verification on a partition: Enroll the camera PIR; [804] Set visual verification options; [804]>[841]: [001] Visual Verification Enable/Disable [002] View Time Window [003] View Other Alarms Input a custom label to identify the camera PIR; [000]>[001] Enable this option on the alternate communicator (in [851]>[010] option 2).
Page 81: Section 6: Programming
Section 6: Programming Section 6: Programming 6.1 How to program This section describes how to view alarm system programming options using the supported keypad types. 6.2 Programming methods The alarm system can be programmed using the following methods: Table 6-1: Programming Methods Method Description Procedure...
Page 82 Section 6: Programming 5. After programming the partition 1 account code, the downloading access code is displayed. Enter the new downloading access code or press [#] to proceed to the next step. The downloading access code must changed from its default value. 6.
Page 83 Section 6: Programming Keypad types The sections below describe how programming is viewed and interpreted using the supported keypad types. For more information, see the instruction sheet included with the keypad. LCD keypad LCD keypads use a full-message display that provides visual and numerical navigation through the programming sections. The Armed light illuminates when Installer Programming mode is activated.
Page 84: Programming Descriptions
Section 6: Programming 6.3 Programming descriptions This section provides descriptions of all alarm controller options programmable by the installer. Adding labels [000] Label Programming Zone and other labels on the alarm system can be customized. Program labels locally or download/upload using DLS. Local label programming is done via a system keypad, as described below. [000] Language selection To select a language: 1.
Page 85 Section 6: Programming Press To Select/Display [SELECT] [ESCAPE] [SPACE] [A], [B], [C], [1] [D], [E], [F], [2] [G], [H], [I], [3] [J], [K], [L], [4] [M], [N], [O], [5] [P], [Q], [R], [6] [S], [T], [U], [7] [V], [W], [X], [8] [Y], [Z], [9], [0] Zone label options To access zone label options such as using ASCII characters, changing letter case and clearing the display, press [*] while in Zone...
Page 86 Section 6: Programming [065] Fire alarm message Use this section to program a custom label that is displayed on keypads during a fire alarm. The maximum label size is 14 x 2 characters. [066] Fail to arm event message This message is displayed on all partition keypads if a user attempts to arm the system when it is not ready to arm. The message clears after five seconds.
Page 87 Section 6: Programming [812][001]-[016] HSM3204CX Corbus repeater label Use this section to create a custom label for the Corbus repeater. Select 001-016 for Corbus repeater 1-16. [815] Alternate communicator label Use this section to create a custom label for the alternate communicator. [820][001]-[016] Siren labels Use this section to create custom labels for wireless sirens on the system.
Page 88 Section 6: Programming seconds and another 30-second delay starts. A code is required to silence the alarm. A tamper or fault causes a fire trouble to log and transmit. Note: The supervision options (NC, SEOL, DEOL, TEOL) do not affect the functionality of this zone. The restored state of this zone type is 5k6, the alarm state is short, and the trouble state is open.
Page 89 Section 6: Programming 017 – 24-Hour Burglary This zone type is active at all times. It reports an alarm if the alarm system is armed or disarmed. This zone type sounds the siren for the length of Bell time-out if the audible attribute is enabled. 018 –...
Page 90 Section 6: Programming 047 - 24-Hour Emergency Instant alarm when activated, audible alarm at default. 048 – 24-Hour Sprinkler Instant alarm when activated, audible alarm at default. 049 – 4-Hour Flood Instant alarm when activated, audible alarm at default. 051 – 24-Hour Latching Tamper Instant alarm when activated, audible alarm at default.
Page 91 Section 6: Programming With an audible alarm active, using the keyswitch when disarmed is the same as entering an access code at the keypad. Activating this zone type during the first 30 seconds of a delayed fire alarm is the same as pressing a key at the keypad (the 90 second delay starts).
Page 92 Section 6: Programming 02 – Bell Steady ON: Siren output is steady when in alarm. OFF: Siren output pulses when in alarm. 03 – Door Chime ON: The keypad chimes when the zone is open and when the zone is secured. OFF: The zone does not chime.
Page 93 Section 6: Programming 14 – Hold Up Verification ON: An alarm from zones of this type can contribute to a verified hold up alarm. Use this attribute with Panic and Hold Up zones. OFF: An alarm from zones of this type does not contribute to a verified hold up alarm. The zone does not cause the hold up verification timer to start counting down, or generate a verified hold up if the alarm is detected while the timer is running.
Page 94 Section 6: Programming Burglary Verification Timer If another zone with the Burglary Verification attribute enabled is violated within the duration of this timer, a burglary verified event is communicated and logged. “Burglary Verified” is displayed on the keypad when the system is disarmed. The burglary verification timer is programmed in minutes.
Page 95 Section 6: Programming Week Valid entries are 000-005. Enter “000” to program a specific date (1-31) in the Day field. Enter 001-005 to program the specific week of the month. 005 is the last week of the month. 1-31 (if 000 is programmed in the Week field). 0-6 (Sunday-Saturday) if 001-005 is programmed in the Week field. Hour Valid entries are 00-23 hours.
Page 96 Section 6: Programming [001]-[324] PGM Partition Assignment This option enables the installer to assign each PGM output to a partition. To assign a PGM to a partition, first select the PGM output (PGM 001-324), then select the partition (1-32). Note: This field is only supported by PGM types that have multiple partition capabilities (e.g., command outputs, away arming). It does not affect system outputs (e.g., ground start pulse).
Page 97 Section 6: Programming 104 – 2-Wire Smoke When this PGM is programmed, the onboard PGM functions as an input instead of an output. 2-wire smoke detectors can be connected to this input, which means that a zone input does not need to be used. The PGM is also supervised, and a trouble condition is generated if a 2.2KΩ...
Page 98 Section 6: Programming 129 – Partition Status Alarm Memory This feature is intended to be used on a keyswitch plate, with a light controlled by this PGM to indicate system status. When the partition is armed, the output activates (steady) at the: beginning of exit delay end of exit delay.
Page 99 Section 6: Programming In the armed state, this output deactivates when the system is disarmed. If an alarm activates this output in the disarmed state, the output deactivates if a valid access code is entered within the bell timeout or if the system is armed after the bell timeout has expired. This output activates for silent and audible alarms or medical conditions only.
Page 100 Section 6: Programming Wireless keypad low battery Wireless siren low battery Wireless key low battery The output can be configured to follow the state of the low battery trouble(s) or it can activate for a period of time and automatically restore.
Page 101 Section 6: Programming If multiple zones are enabled, any active zone in that group triggers the output. The PGM will not activate again until all zones are restored. 200 – Zone Follower - PGM By Zone This option allows the PGM to activate when the assigned zone is opened and deactivate when the zone is restored or, if programmed, when a valid access code is entered.
Page 102 Section 6: Programming 103 – Sensor Reset [*][7][2] 01 – True Output/Inverted ON: deactivated during normal operation. Activated when triggered. OFF: active during normal operation. Deactivated when triggered. 03 – Access Code Required / No Code Required ON: Access code required for activation OFF: No access code required for activation 107 –...
Page 103 Section 6: Programming OFF: active during normal operation. Deactivated when triggered. 116 – Armed Away Mode 01 – True Output/Inverted ON: deactivated during normal operation. Activated when triggered. OFF: active during normal operation. Deactivated when triggered. 117 – Armed Stay Mode 01 –...
Page 104 Section 6: Programming 02 – Timed Output / Latched Output ON: output remains active until the PGM output timer expires. OFF: output remains active until an access code has been entered. 04 – Fire Alarm ON: activates with fire alarm, [F] key, fire zones, 2-wire smoke. OFF: does not activate with fire alarm.
Page 105 Section 6: Programming 05 – Loss of Clock ON: activates on loss of clock trouble condition. OFF: does not activate on loss of clock trouble condition. 06 – DC Trouble ON: activates if a panel low or no battery trouble is detected, or if an HSM2204/2300 1-4 low or no battery trouble is detected. OFF: does not activate on DC Trouble condition.
Page 106 Section 6: Programming HSM2300 1 – 4 HSM2208 01 – 16 HSM3204CX HSM3408 HSM3350 OFF – does not activate if a module supervisory trouble is detected. 14 – Module Tamper ON – activates if any of the following module tamper conditions is present: HSM2HOST Keypad 01 –...
Page 107 Section 6: Programming 07 – Medical Alarm ON: activates on medical alarm. OFF: does not activate on medical alarm. 08 – Supervisory ON: activates on supervisory alarm. OFF: does not activate on supervisory alarm. 09 – Priority Event ON: activates on priority alarm. OFF: does not activate on priority alarm.
Page 108 Section 6: Programming 10 – Battery Absent ON: activates when a battery absent trouble occurs. OFF: does not activate when a battery absent trouble occurs. 165 – Prox Used 01 – True Output/Latched Output ON: deactivated during normal operation. Activated when triggered. OFF: activated during normal operation.
Page 109 Section 6: Programming 201 – 231 Zone Follower Zones 1-248 01 – True Output/Inverted ON: deactivated during normal operation. Activated when triggered. OFF: activated during normal operation. Deactivated when triggered. 02 – Timed Output ON: output remains active until the PGM output timer expires. OFF: output remains active until an access code has been entered.
Page 110 Section 6: Programming System Options [013] System Option 1 1 – NC Loop/EOL ON: All zones are wired as normally closed circuits with returns connected to a COM terminal. The end-of-line resistor is not required. An alarm is generated when the circuit is opened. OFF: All zones must be wired with an end-of-line resistor configuration, determined by option 2 below.
Page 111 Section 6: Programming 2 – Bell Squawk on Auto-Arm ON: The siren squawks once every 10 seconds during the auto-arm pre-alert time. OFF: The siren does not squawk during auto-arm pre-alert. 3 – Bell Squawk On Exit ON: The siren squawks once per second during exit delay, changing to 3 squawks per second for the final 10 seconds. OFF: The siren does not squawk for exit delay conditions.
Page 112 Section 6: Programming OFF: The master code may be programmed by the user using the [*][5][Master Code] command. The master code may also be programmed in Installer Programming. 7 – Telephone Line Monitor Enable ON: The TLM function is active and the system indicates a trouble condition when using the [*][2] View Trouble Conditions command. OFF: The TLM function is deactivated and telephone line troubles are not indicated by the system.
Page 113 Section 6: Programming 8 – Keypad Tampers Enabled ON: All keypads containing tamper switches generate tamper alarms and restores. OFF: The tamper switches on all keypads do not generate tamper alarms. Note: If this option is used, all keypads should be properly installed and secured (tamper restored) before enabling the option. Note: Must be ON for UL/ULC commercial burglary listed installations.
Page 114 Section 6: Programming [018] System Option 6 1 – Test Transmission Exception ON: The alarm system does not send a test transmission if a transmission was sent to the receiver within the programmed interval as set in section [377]>See "[003] – Periodic Test Transmission Cycle" on page 132. OFF: Test transmissions are always sent at the programmed interval.
Page 115 Section 6: Programming OFF: Wireless device faults do not sound the siren. 2 – Latching Troubles ON: Troubles remain on the system until viewed via [*][2], even if they are restored. The trouble condition is cleared when the"Press (*) to Acknowledge" option is selected within the [*][2] menu after the trouble has restored. The Trouble LED turns off unless other troubles are present.
Page 116 Section 6: Programming To obtain the reset code, the user must provide a corresponding system lock code, displayed on the keypad when one of the following conditions occurs: the system has been disarmed (Duress Code excluded) the bell has timed out (24Hr zones) an access code has been entered (24Hr zones) On an LCD keypad, the message “REMOTE RESET RQD”...
Page 117 Section 6: Programming 2 – Keypad Blanking while Armed ON: If [016][3] is disabled within 30 seconds after the exit delay terminates, the keypad blanks (no indicator lights). OFF:The keypad blanks when the system is armed or disarmed. Note: For systems compliant with EN50131-1 and EN50131-3, option [021] bit 2 “Keypad blanking while armed” must be ON. 3 –...
Page 118 Section 6: Programming OFF: When a trouble is detected on the system, trouble beeps are sounded at the keypad. Note: This option must be OFF for UL Residential Fire applications. Note: To silence the Fire Trouble beep, press [*][2] and exit. Accessing [*][2] requires a valid user code. 8 –...
Page 119 Section 6: Programming [024] System Option 12 1 – Reserved 2 – Reserved 3 – AC/DC Inhibits Arming ON: The system cannot be armed when an AC or battery trouble is present. This includes keypad, keyswitch, automatic, and DLS arming. An error tone is generated if the user attempts to arm the system during an AC/DC trouble. Note: Displaying AC troubles ([016] option 2) is strongly recommended if this option is enabled.
Page 120 Section 6: Programming OFF: No attempt is made to contact the central station if dial tone is not present. Note: Force Dial must be enabled for UL installations. 3 – Test Transmission Counter in Minutes ON – When the option is on, the Periodic Test Transmission interval programmed in section [377][003] will be 000-255 minutes instead of 000-255 days or hours.
Page 121 Section 6: Programming [042] Verified Events Burglary Verified Counter This counter determines the number of burglary alarms that must occur within the Burglary verification window before a confirmed Burglary Verified alarm is logged and communicated. Zones with the burglary verification zone attribute enabled contribute to the generation of a confirmed Burglary Verified alarm in conjunction with this counter and the burglary verification timer.
Page 122 Section 6: Programming [006] – Partition No Activity Arming Timer Use this section to program the duration of the No Activity timer. If this timer expires and no zones have been activated, the partition arms in Away mode (exit delay will not sound). When the timer expires, keypad buzzers activate for the time programmed in No Activity Arming Pre-Alert (see below).
Page 123 Section 6: Programming [201]-[232] Partition Zone Assignment Zones can be assigned to any partition. Global zones are zones assigned to more than one partition. A global zone is only armed when all assigned partitions are armed. The zone is disarmed when any of the assigned partitions is disarmed. By default, zones 1 through 8 are assigned to partition 1.
Page 124 Section 6: Programming [05] Alternate Communicator Receiver 3 Events are communicated through cellular receiver 3. [06] Alternate Communicator Receiver 4 Events are communicated through cellular receiver 4. [301] Phone Number Programming Section [301] is used to program up to 4 telephone numbers used to communicate with the central station over PSTN. [001] The phone number used to communicate with receiver 1 [002] The phone number used to communicate with receiver 2 [003] The phone number used to communicate with receiver 3...
Page 125 Section 6: Programming 6 – Burglary Verified When using Cross Zoning, this reporting code is sent when two crossed zones go into alarm during the cross zone timer. When using Police Code or sequential detection, this reporting code is sent when any two zones that have the burglary verification attribute enabled go into alarm.
Page 126 Section 6: Programming [202] Open/Close Events 2 1 – Automatic Closing This reporting code is transmitted when a partition is automatically armed or schedule armed and uses the Opening call direction group. 2 – Automatic Disarm This reporting code is transmitted when a partition is automatically disarmed when a scheduled time of day is reached. 3 –...
Page 127 Section 6: Programming 5/6 – Auxiliary Power Supply Trouble/Restore This reporting code is transmitted when an auxiliary voltage supply trouble occurs or is restored. This reporting code is sent to the System Maintenance call direction group. 7/8 – Overcurrent Trouble/Restore This reporting code is transmitted when an overcurrent trouble occurs or is restored.
Page 128 Section 6: Programming [313] Maintenance Events 3 1/2 – Firmware Update Begin/was Successful Sent when a remote firmware update is initiated/ is successfully completed. 3 – Firmware Update Fail Sent after an unsuccessful remote firmware update. [314] Maintenance Events 4 1/2 –...
Page 129 Section 6: Programming 3/4 – Reserved 5/6 – Reserved 7/8 – Alt. Comm Radio/SIM Failure/Restore Sent when the alternate communicator experiences trouble or restore of the radio/SIM. [352] Alternate Communicator 2 1/2 – Alt. Comm Network Fault/Restore Sent when the alternate communicator loses or restores communication with the network. 5/6 –...
Page 130 Section 6: Programming Ground Fault Fire Supervisory (Wireless) TLM Trouble AC Trouble FTC Trouble This reporting code is sent in place of the standard Periodic Test Transmission code. 5 – System Test Sent when a manual system test is performed ([*][6][Master Code][04]). System Communications The programming options in this section are used to configure communications between the alarm system and the central station.
Page 131 Section 6: Programming [01] Receiver 1 [02] Receiver 2 [03] Receiver 3 [04] Receiver 4 [002] Tampers (Including System Tampers)/ Restore These options control which receiver paths are enabled for Partition 1-32 Tamper and Restore event reporting codes. To assign an event to a receiver, select one of the following options: [01] Receiver 1 [02] Receiver 2 [03] Receiver 3...
Page 132 Section 6: Programming [002] – Communication Delays Transmission Delay (seconds) This value defines the delay before an alarm is transmitted. The delay is for zones which have the Transmission Delay attribute enabled. Valid entries are from 000 to 255 seconds (0-45 seconds for CP-01).
Page 133 Section 6: Programming [013] – Delay Between Force Attempts This programming option is used to set the length of time the alarm system waits between the first dialing attempt and the force dial attempt. Valid Entries are 001-255 seconds. Default is 020. [014] –...
Page 134 Section 6: Programming This continues until communication is successful or the sequence has been repeated 5 times (depending on the number of maximum dialing attempts). If all 5 attempts fail, an FTC trouble for the primary phone number is logged. All backup receivers automatically use the same call directions and format as the primary receiver.
Page 135 Section 6: Programming Note: Must be ON for ULC commercial fire monitoring listed installations. [382] Communicator Option 3 1 – Reserved 2 – Walk Test Communications ON: Zone alarms that occur during Walk Test are communicated if programmed to do so. OFF: Zone alarms during Walk Test are not communicated.
Page 136 Section 6: Programming Receiver 2 uses the same format programmed for Receiver 1. OFF: Receiver 2 is independent and will communicate if a number and format are programmed. 3 – Receiver 3 Backup Option ON: Receiver 3 backs up Receiver 2. Receiver 3 is only used if an FTC event is detected on Receiver 2. Receiver 3 uses the same format programmed for Receiver 2.
Page 137 Section 6: Programming OFF: The user cannot enable a downloading window. 3 – DLS CallBack ON : When a downloading call is answered, both the computer and the alarm system hang up. The alarm system then calls the downloading computer back using the [402] downloading telephone number and begins the DLS session. Note: Disable this option if using more than one downloading computer.
Page 138 Section 6: Programming Programming the access code as FFFFFF disables SA access. Once an SA connection is established, multiple attempts to input the correct downloading access code (programmed in [012]) is allowed. The operator is allowed three attempts to enter the correct access code. If these attempts are unsuccessful, the alarm system disconnects and a new attempt must be made.
Page 139 Section 6: Programming Each schedule contains 4 intervals, for Command Outputs 1-4. Within each interval, a start time and end time can be programmed for each day of the week. Holiday schedules 1-4 can also be selected. To enable the command output to follow a schedule, program the command output in section [009] and then enter schedule 001 - 004 in section [011].
Page 140 Section 6: Programming [851] Alternate Communicator Programming The programming sections described in this document can be viewed at the keypad. To start programming, enter [*] [8][installer code] [851] [section number], where section number is the 3-digit section number referenced in this section. Installers may review/record programming options at the panel keypad.
Page 141 Section 6: Programming [4] Primary Path Default (OFF) ON: Cellular channel is the primary path. Ethernet channel is the secondary path. OFF: Ethernet channel is the primary path in a dual communicator. Cellular channel is the secondary path. [6] Remote Firmware Upgrade Default (ON) ON: The control panel firmware can be remotely upgraded using the Ethernet/cellular paths.
Page 142 Section 6: Programming Note: If no value is programmed and DHCP is used, the DHCP server will assign this value. If an address is programmed and DHCP is used, the programmed address will be used instead of the DHCP address. Programming Options [010] System Toggle Options 3 [1] 2-Way Audio Over Cellular.
Page 143 Section 6: Programming Note: Enable Receiver Group Pair in section [851][010] option 4. Program auto-routing in section [300]. 01 = Ethernet Receiver 1 02 = Ethernet Receiver 2 03 = Cellular Receiver 1 04 = Cellular Receiver 2 For example, an entry of 0103 means the receiver group includes Ethernet Receiver 1 and Cellular Receiver 1. An entry of 00 or FF denotes no receiver (disabled).
Page 144 Section 6: Programming HEX Value Offset Hours Standard Abbreviation Location 8.75 ACWST Australian Central Western Standard Time Korea Standard Time ACST Australian Central Standard Time AEST Australian Eastern Standard Time 10.5 LHST Lord Howe Standard Time Vanuatu Time 11.5 Norfolk Island Time NZST New Zealand Standard Time 12.75...
Page 145 Section 6: Programming Program 00 to disable this event transmission or FF to enable. See system test options for details on settings. [027] Ethernet 2 Test Transmission Default (00) Program 00 to disable this event transmission or FF to enable. See system test options (previous page) for details on settings. [028] Cellular Receiver 3 Test Transmission Default (FF) Program 00 to disable this event transmission or FF to enable.
Page 146 Section 6: Programming [105] Ethernet Receiver 1 UDP Local Port Default (03060) Use this section to set the value of the UDP local outgoing port. Set the value of this port when the installation is located behind a firewall and must be assigned a particular port number as determined by the central station system administrator. Valid range: 00000 - 65535.
Page 147 Section 6: Programming Ethernet Options [124] Ethernet Test Transmission Time Default (9999) Enter a 4 digit number (0000-2359) using the 24-hour clock format (HHMM) to set the test transmission time of day. Valid range: 00 - 23 hours (HH) and 00 - 59 minutes (MM). Programming a value of 9999 will disable the test transmission time. Note: The internal date and time will automatically be programmed when the unit communicates with the primary receiver.
Page 148 Section 6: Programming Cellular Receiver 4 Options [211] Cellular Receiver 4 Account Code Default (0000000000) The account code is used by the central station to distinguish between different transmitters. This account code is used when transmitting signals to the central station receiver. Signals received on the panel will use the panel account number. Valid range: 0000000001 - FFFFFFFFFE.
Page 149 Section 6: Programming The internal date and time will be automatically programmed by the primary receiver only. [225] Cellular Test Transmission Cycle Default (000000) This value represents the interval in between test transmissions in minutes. Valid range: 000000 - 999999 minutes. Once the unit has sent the initial periodic test transmission, all future test transmissions will be offset by the programmed number of minutes.
Page 150 Section 6: Programming This option controls the polling interval from the alarm panel to the integration interface for the purpose of optimizing data usage. The shorter the interval, the higher the data usage. [428] Session 1 Integration Server IP This section programs the IP address of the third party server. Do not program this section if a domain name is programmed in setion [431].
Page 151 Section 6: Programming [979] - Cellular Network CSQ [980] - Radio Reset Codes [981] - Radio Type [982] - Radio Firmware Version [983] - Firmware Update Diagnostics Section Firmware updates for panel and the communicator itself can be made from the communicator. Table 6-10: Response Code Descriptions and Corresponding Actions Response Description of Response Code...
Page 152 Section 6: Programming Response Description of Response Code Corresponding Action Code Remote firmware update disabled Enable remote firmware update in the communicator in order to perform remote system firmware update. Local Status Update States Firmware file empty No action required. Communicator currently does not have any firmware files. Firmware download in progress No action required.
Page 153 Section 6: Programming Table 6-13: Trouble Indicator - Digits 4 and 5 Trouble Trouble Possible Trouble description and possible solutions indication indicator causes digit No indication No power To fix this trouble complete the following checks: Check the power connections between the panel and the commicator. Check the PC-link cable connection between the panel and the communicator.
Page 154 Section 6: Programming Trouble Trouble Possible Trouble description and possible solutions indication indicator causes digit All LEDs flash Boot loader To fix this trouble, disconnect power from the communicator and then reconnect power to the communicator. together failed Red and yel- Initialization This trouble indicates the communicator is initializing.
Page 155 Section 6: Programming [992] - Ethernet IP Address This section displays the IP address of the Ethernet connection. This value is programmed in section [001] or assigned by DHCP. [993] - Ethernet Gateway IP Address This section displays the IP address of the Ethernet connection. This value is programmed in section [001] or assigned by DHCP. [994] - Cellular IP Address This section displays the current dynamic IP address assigned by DHCP to the cellular connection.
Page 156 Section 6: Programming DLS Access Code: The 6-digit DLS access code used in programming section [403]. Partition 1 Entry Delay: The 3-digit entry delay duration for partition 1, in seconds, used in programming [005][001] option 1. Partition 1 Exit Delay: The 3-digit exit delay duration for partition 1, in seconds, used in programming section [005][001] option Installer Code: The 4, 6 or 8-digit installer access code used in programming section [006][001].
Page 157 Section 6: Programming [000] – Auto Enroll Modules When this mode is selected, the alarm system automatically enrolls all modules connected to the Corbus. The total number of modules currently enrolled are displayed on the keypad. Enter sub-section [000] to begin auto enrollment of all new modules. The auto enroll screen will show the following: KP = Number of keypad type modules IO = Number of zone and output type modules M = Number of other type modules...
Page 158 Section 6: Programming [000] – View All Modules [101] – Keypads [102] – 8-zone Expander Modules [103] – 8-output Expander Modules [104] – 8 I/O Expander Module [106] – HSM2Host [108] – HSM2955 [109] – Power Supply [110] – 4 High Current Output [111] –...
Page 159 Section 6: Programming Diagnostics The Diagnostics feature provides a live measurement of voltage, current, and battery condition for the alarm panel and devices through the system keypad. This information can be used in place of a multimeter to troubleshoot panel and module troubles. To view specific measurements, scroll to the corresponding section: [000] Panel [001] DC input voltage/current...
Page 160 Section 6: Programming No communications occur for events from a zone in soak test, with the exception of low battery and low battery restore events and faults generated by low sensitivity in a smoke detector. A message indicating that the zone is in soak test is displayed when scrolling left or right in the base disarmed keypad menu. Note: Soak test is not applied to temperature detector events if it is enabled.
Page 161: Section 7: Programming Worksheets
Section 7: Programming Worksheets Section 7: Programming Worksheets Note: listed options are required for EN 50131 Compliant Installations. 7.1 Label Programming [000] Label Programming Description on page 84 [000] – Language Selection (2-digit decimal; Default: 01) 01 – English 06 – Dutch 11 –...
Page 162 Section 7: Programming Worksheets 085: 086: 087: 088: 089: 090: 091: 092: 093: 094: 095: 096: 097: 098: 099: 100: 101: 102: 103: 104: 105: 106: 107: 108: 109: 110: 111: 112: 113: 114: 115: 116: 117: 118: 119: 120: 121: 122: 123:...
Page 163 Section 7: Programming Worksheets 211: 212: 213: 214: 131: 215: 216: 217: 218: 219: 220: 221: 222: 223: 224: 225: 226: 227: 228: 229: 230: 231: 232: 233: 234: 235: 236: 237: 238: 239: 240: 241: 242: 243: 244: 245: 246: 247: 248:...
Page 164 Section 7: Programming Worksheets 125 – Partition 25 Label (1 x 14 Characters): 126 – Partition 26 Label (1 x 14 Characters): 127 – Partition 27 Label (1 x 14 Characters): 128 – Partition 28 Label (1 x 14 Characters): 129 –...
Page 165 Section 7: Programming Worksheets 003 – Partition 8 Command Output 3: 004 – Partition 8 Command Output 4: 209 – Partition 9 Command Output Labels 001 – Partition 9 Command Output 1: (2 x 14 Characters) 002 – Partition 9 Command Output 2: 003 –...
Page 166 Section 7: Programming Worksheets 219 – Partition 19 Command Output Labels 001 – Partition 19 Command Output 1: (2 x 14 Characters) 002 – Partition 19 Command Output 2: 003 – Partition 19 Command Output 3: 004 – Partition 19 Command Output 4: 220 –...
Page 167 Section 7: Programming Worksheets 003 – Partition 29 Command Output 3: 004 – Partition 29 Command Output 4: 230 – Partition 30 Command Output Labels 001 – Partition 30 Command Output 1: (2 x 14 Characters) 002 – Partition 30 Command Output 2: 003 –...
Page 168 Section 7: Programming Worksheets 004 – Zone Expander 4 Label: 019 – Zone Expander 19 Label: 005 – Zone Expander 5 Label: 020 – Zone Expander 20 Label: 006 – Zone Expander 6 Label: 021 – Zone Expander 21 Label: 007 –...
Page 169 Section 7: Programming Worksheets 809 – HSM2300 Power Supply Label (1 X 14 Characters) 001 – Power Supply 1 Label: 002 – Power Supply 2 Label: 003 – Power Supply 3 Label: 004 – Power Supply 4 Label: 810 – HSM2204 High-Current Output Supply Label (1 X 14 Characters) Description on page 86 001 –...
Page 170: Zone Setup
Section 7: Programming Worksheets 007 – Siren 7 Label: 015 – Siren 15 Label: 008 – Siren 8 Label: 016 – Siren 16 Label: 821 – Repeater Label (1 X 14 Characters) [000] Description on page 87 001 – Repeater 1 Label: 002 –...
Page 171 Section 7: Programming Worksheets Zone Attribute Defaults (Description on page 91) Zone Attributes 1 – Bell Audible 5 –Force Arm 9 – Normally Closed EOL 13 - Zone 2-way Audio Activation 2 – Bell Steady 6 – Swinger Shutdown 10 – Single EOL 14 - Hold Up Verification 3 –...
Page 172 Section 7: Programming Worksheets Zone Attributes ü Auto Verify Fire Fire Supervisory ü 24-Hour Gas CP-01 CP-01 ü ü 24-Hour CO ü ü ü ü 24-Hour CP-01 CP-01 ü Holdup ü ü ü 24-Hour CP-01 CP-01 ü Panic ü ü 24-Hour CP-01 ü...
Page 173: End Of Line Resistance
Section 7: Programming Worksheets Zone Attributes ü Momentary Keyswitch Disarm ü Maintained Keyswitch Disarm ü ü Door Bell ü Push to Set 7.3 End Of Line Resistance [004] End of Line Resistance description on page 93 001 – Single EOL Alarm (Default 5.6 kΩ) Valid range: 0.5 kΩ...
Page 174 Section 7: Programming Worksheets [005] System Times description on page 93 004 – Partition 4 Timer Entry Delay 1: See partition 1 for defaults Entry Delay 2: Exit Delay: Settle Delay: 005 – Partition 5 Timer Entry Delay 1: See partition 1 for defaults Entry Delay 2: Exit Delay: Settle Delay:...
Page 175 Section 7: Programming Worksheets [005] System Times description on page 93 See partition 1 for defaults Entry Delay 2: Exit Delay: Settle Delay 015 – Partition 15 Timer Entry Delay 1: See partition 1 for defaults Entry Delay 2: Exit Delay: Settle Delay 016 –...
Page 176 Section 7: Programming Worksheets [005] System Times description on page 93 Exit Delay: Settle Delay 025 – Partition 25 Timer Entry Delay 1: See partition 1 for defaults Entry Delay 2: Exit Delay: Settle Delay 026 – Partition 26 Timer Entry Delay 1: See partition 1 for defaults Entry Delay 2:...
Page 177: Access Codes
Section 7: Programming Worksheets [005] System Times description on page 93 902 – Daylight Savings End Month(Default: 011) Week (Default: 001): Day (Default: 000): Hour (Default: 002): Increment (Default : 001): 7.5 Access Codes [006] Installer-Defined Codes (4/6/8-Digit Decimal) 001 – Installer Code (Default:55555555) (4/6/8-Digit Decimal) 002 –...
Page 178 Section 7: Programming Worksheets [008] [000 - 324] PGM Timer Programming PGM 15 PGM 16 PGM 17 HSM2204 #4 PGM 18 PGM 19 PGM 20 PGM 37 HSM2208 #1 PGM 38 PGM 39 PGM 40 PGM 41 PGM 42 PGM 43 PGM 44 PGM 45 HSM2208 #2...
Page 179 Section 7: Programming Worksheets [008] [000 - 324] PGM Timer Programming PGM 69 PGM 70 HSM2208 #5 PGM 71 PGM 72 PGM 73 PGM 74 PGM 75 PGM 76 PGM 77 PGM 78 HSM2208 #6 PGM 79 PGM 80 PGM 81 PGM 82 PGM 83 PGM 84...
Page 180 Section 7: Programming Worksheets [008] [000 - 324] PGM Timer Programming PGM 109 HSM2208 #10 PGM 110 PGM 111 PGM 112 PGM 113 PGM 114 PGM 115 PGM 116 PGM 117 HSM2208 #11 PGM 118 PGM 119 PGM 120 PGM 121 PGM 122 PGM 123 PGM 124...
Page 181 Section 7: Programming Worksheets [008] [000 - 324] PGM Timer Programming PGM 149 HSM2208 #15 PGM 150 PGM 151 PGM 152 PGM 153 PGM 154 PGM 155 PGM 156 PGM 157 HSM2208 #16 PGM 158 PGM 159 PGM 160 PGM 161 PGM 162 PGM 163 PGM 164...
Page 182 Section 7: Programming Worksheets [008] [000 - 324] PGM Timer Programming PGM 314 PGM 315 PGM 316 PGM 317 PGM 318 PGM 319 PGM 320 PGM 321 PGM 322 PGM 323 PGM 324 [009] [001] - [164] PGM Types 100 – Null PGM 121 –...
Page 183 Section 7: Programming Worksheets [009] [001] - [164] PGM Types (3-Digit Decimal) Valid Range: 001-216 001 Default: 121 Command Output 1 002 Default: 156 System Event 003 - 324 Default: 101 Burg and Fire Bell Follower Description on page 96 Zone Follower by Zone Prox.
Page 184 Section 7: Programming Worksheets [009] [001] - [164] PGM Types HSM2208 #2 PGM 45 PGM 46 PGM 47 PGM 48 PGM 49 PGM 50 PGM 51 PGM 52 HSM2208 #3 PGM 53 PGM 54 PGM 55 PGM 56 PGM 57 PGM 58 PGM 59 PGM 60...
Page 185 Section 7: Programming Worksheets [009] [001] - [164] PGM Types HSM2208 #7 PGM 85 PGM 86 PGM 87 PGM 88 PGM 89 PGM 90 PGM 91 PGM 92 HSM2208 #8 PGM 93 PGM 94 PGM 95 PGM 96 PGM 97 PGM 98 PGM 99 PGM 100...
Page 186 Section 7: Programming Worksheets [009] [001] - [164] PGM Types HSM2208 #12 PGM 125 PGM 126 PGM 127 PGM 128 PGM 129 PGM 130 PGM 131 PGM 132 HSM2208 #13 PGM 133 PGM 134 PGM 135 PGM 136 PGM 137 PGM 138 PGM 139 PGM 140...
Page 187 Section 7: Programming Worksheets [009] [001] - [164] PGM Types HSM3204CX#17 PGM 294 PGM 295 PGM 296 PGM 297 PGM 298 PGM 299 PGM 300 PGM 301 PGM 302 PGM 303 PGM 304 PGM 305 PGM 306 PGM 307 PGM 308 PGM 309 PGM 310 PGM 311...
Page 188 Section 7: Programming Worksheets [010] [000 - 164] PGM Attributes R 01 – True Output 102 – Delay Fire and Burg o 03 – Code Required 103 – Sensor Reset [*][7][2] R 01 – True Output 107 - External Siren R 01 –...
Page 189 Section 7: Programming Worksheets [010] [000 - 164] PGM Attributes R 01 – True Output 149 – Alternate Communicator R 02 – Timed Output o 04 – Fire Alarm o 05 – Panic Alarm o 06 – Burglary Alarm o 07 – Open/Close o 08 –...
Page 190 Section 7: Programming Worksheets [010] [000 - 164] PGM Attributes R 01 – True Output 161 – DC Trouble o 02 – Timed Output R 09 – Battery Low R 10 – Battery Absent R 01 – True Output 165 – Prox Used R 01 –...
Page 191 Section 7: Programming Worksheets [010] [000 - 164] PGM Attributes R 01 – True Output 201 Zone Follower Zones 1-8 o 02 – Timed Output 202 Zone Follower Zones 9-16 R 04 – Latching 203 Zone Follower Zones 17-24 o 05 – Follow Alarm 204 Zone Follower Zones 25-32 R 09 –...
Page 192 Section 7: Programming Worksheets [010] PGM Attribute Assignment: (16-Bit Toggles) Description on page 109 Zone Follower by Zone Prox. Used Schedule (000-248; Default 000) (000-095; Default 000) (000-004; Default 000) HSM2204 #1 PGM 5 PGM 6 PGM 7 PGM 8 HSM2204 #2 PGM 9 PGM 10...
Page 193 Section 7: Programming Worksheets [010] PGM Attribute Assignment: (16-Bit Toggles) Description on page 109 Zone Follower by Zone Prox. Used Schedule (000-248; Default 000) (000-095; Default 000) (000-004; Default 000) PGM 57 PGM 58 PGM 59 PGM 60 HSM2208 #4 PGM 61 PGM 62 PGM 63...
Page 194 Section 7: Programming Worksheets [010] PGM Attribute Assignment: (16-Bit Toggles) Description on page 109 Zone Follower by Zone Prox. Used Schedule (000-248; Default 000) (000-095; Default 000) (000-004; Default 000) HSM2208 #8 PGM 93 PGM 94 PGM 95 PGM 96 PGM 97 PGM 98 PGM 99...
Page 195 Section 7: Programming Worksheets [010] PGM Attribute Assignment: (16-Bit Toggles) Description on page 109 Zone Follower by Zone Prox. Used Schedule (000-248; Default 000) (000-095; Default 000) (000-004; Default 000) PGM 130 PGM 131 PGM 132 HSM2208 #13 PGM 133 PGM 134 PGM 135 PGM 136...
Page 196 Section 7: Programming Worksheets [010] PGM Attribute Assignment: (16-Bit Toggles) Description on page 109 Zone Follower by Zone Prox. Used Schedule (000-248; Default 000) (000-095; Default 000) (000-004; Default 000) PGM 295 PGM 296 PGM 297 PGM 298 PGM 299 PGM 300 PGM 301 PGM 302...
Page 197 Section 7: Programming Worksheets [011] PGM Configuration Options Description on page 109 Zone Follower by Zone Prox. Used Schedule (000-248; Default 000) (000-095; Default 000) (000-004; Default 000) PGM 4 HSM2204 #1 PGM 5 PGM 6 PGM 7 PGM 8 HSM2204 #2 PGM 9 PGM 10...
Page 198 Section 7: Programming Worksheets [011] PGM Configuration Options Description on page 109 Zone Follower by Zone Prox. Used Schedule (000-248; Default 000) (000-095; Default 000) (000-004; Default 000) PGM 57 PGM 58 PGM 59 PGM 60 HSM2208 #4 PGM 61 PGM 62 PGM 63 PGM 64...
Page 199 Section 7: Programming Worksheets [011] PGM Configuration Options Description on page 109 Zone Follower by Zone Prox. Used Schedule (000-248; Default 000) (000-095; Default 000) (000-004; Default 000) HSM2208 #8 PGM 93 PGM 94 PGM 95 PGM 96 PGM 97 PGM 98 PGM 99 PGM 100...
Page 200 Section 7: Programming Worksheets [011] PGM Configuration Options Description on page 109 Zone Follower by Zone Prox. Used Schedule (000-248; Default 000) (000-095; Default 000) (000-004; Default 000) PGM 131 PGM 132 HSM2208 #13 PGM 133 PGM 134 PGM 135 PGM 136 PGM 137 PGM 138...
Page 201: System Lockout
Section 7: Programming Worksheets [011] PGM Configuration Options Description on page 109 Zone Follower by Zone Prox. Used Schedule (000-248; Default 000) (000-095; Default 000) (000-004; Default 000) PGM 297 PGM 298 PGM 299 PGM 300 PGM 301 PGM 302 PGM 303 PGM 304 PGM 305...
Page 202: System Options
Section 7: Programming Worksheets [012] System Lockout (3-Digit Decimal) Description on page 109 Remote Lockout Duration: (Range: 001-255; Default 060) 7.8 System Options [013] System Options 1 Description on page 110 o 1 – NC Loop/EOL o 2 – DEOL/SEOL R 2 –...
Page 203 Section 7: Programming Worksheets R 2 – AC Trouble Light Flashes o 3 – Keypad Blanking R 3 – Keypad Blanking o 4 – Keypad Blanking Requires Code R 4 – Keypad Blanking Requires Code R 5 – Keypad Backlighting o6 –...
Page 204 Section 7: Programming Worksheets o3 – Reserved o 4 – Reserved o 5 – Audible Bus Fault o 6 – Duress Code R7 – Temperature in Celsius o 8 – Reset After Zone Activation [020] System Options 8 Description on page 115 o 1 –...
Page 205 Section 7: Programming Worksheets o 6 – 2- Way Audio Disconnect o 7 – Trouble Beeps Are Silent o 8 – Keyswitch Arms in Away Mode R 8 – Keyswitch Arms in Away Mode [023] System Options 11 Description on page 118 o 1 –...
Page 206: Auto Arm/Disarm
Section 7: Programming Worksheets o 6 – Tone Generated-2100Hz o 7 – DLS Window o 8 – FTC Audible Bell [040] User Authentication Description on page 120 R 1 – User Code or Prox. Tag o 2 – User Code and Prox. Tag [041] Access Code Digits Description on page 120 R 00 –...
Page 207 Section 7: Programming Worksheets 002 – Partition 2 Auto-Disarm Times: 24-Hour: Wednesday: (4-digit HH:MM) Sunday: Thursday: Default: 9999 Monday: Friday: Tuesday: Saturday: Holiday 1: o On R Off Holiday 3: o On R Off 003 – Partition 2 Auto-Disarming Holiday Schedule: Holiday 2: o On R Off Holiday 4: o On R Off (3-digit decimal)
Page 208 Section 7: Programming Worksheets 001 – Partition 5 Auto-Arming Times: 24-Hour: Wednesday: (4-digit HH:MM) Sunday: Thursday: Default: 9999 Monday: Friday: Tuesday: Saturday: 002 – Partition 5 Auto-Disarm Times: 24-Hour: Wednesday: (4-digit HH:MM) Sunday: Thursday: Default: 9999 Monday: Friday: Tuesday: Saturday: Holiday 1: o On R Off Holiday 3: o On R Off 003 –...
Page 209 Section 7: Programming Worksheets 005 – Partition 7 Auto-Arming Postpone Timer (Default: 000): 006 – Partition 7 No Activity Arming Timer (Default: 000): 007 – Partition 7 No Activity Arming Pre-Alert Timer (Default: 001): [158] Partition 8 Auto-Arm/Disarm 001 – Partition 8 Auto-Arming Times: 24-Hour: Wednesday: (4-digit HH:MM)
Page 210 Section 7: Programming Worksheets Tuesday: Saturday: Holiday 1: o On R Off Holiday 3: o On R Off 003 – Partition 10 Auto-Disarming Holiday Schedule: Holiday 2: o On R Off Holiday 4: o On R Off (3-digit decimal) 004 – Partition 10 Auto-Arming Pre-Alert (Default: 004): 005 –...
Page 211 Section 7: Programming Worksheets Tuesday: Saturday: 002 – Partition 13 Auto-Disarm Times: 24-Hour: Wednesday: (4-digit HH:MM) Sunday: Thursday: Default: 9999 Monday: Friday: Tuesday: Saturday: 003 – Partition 13 Auto-Disarming Holiday Schedule: Holiday 1: o On R Off Holiday 3: o On R Off Holiday 2: o On R Off Holiday 4: o On R Off (3-digit decimal)
Page 212 Section 7: Programming Worksheets [166] Partition 16 Auto-Arm/Disarm 001 – Partition 16 Auto-Arming Times: 24-Hour: Wednesday: (4-digit HH:MM) Sunday: Thursday: Default: 9999 Monday: Friday: Tuesday: Saturday: 002 – Partition 16 Auto-Disarm Times: 24-Hour: Wednesday: (4-digit HH:MM) Sunday: Thursday: Default: 9999 Monday: Friday: Tuesday:...
Page 213 Section 7: Programming Worksheets 004 – Partition 18 Auto-Arming Pre-Alert (Default: 004): 005 – Partition 18 Auto-Arming Postpone Timer (Default: 000): 006 – Partition 18 No Activity Arming Timer (Default: 000): 007 – Partition 18 No Activity Arming Pre-Alert Timer (Default: 001): [169] Partition 19 Auto-Arm/Disarm 001 –...
Page 214 Section 7: Programming Worksheets Default: 9999 Monday: Friday: Tuesday: Saturday: 003 – Partition 21 Auto-Disarming Holiday Schedule: Holiday 1: o On R Off Holiday 3: o On R Off Holiday 2: o On R Off Holiday 4: o On R Off (3-digit decimal) 004 –...
Page 215 Section 7: Programming Worksheets Default: 9999 Monday: Friday: Tuesday: Saturday: 002 – Partition 24 Auto-Disarm Times: 24-Hour: Wednesday: (4-digit HH:MM) Sunday: Thursday: Default: 9999 Monday: Friday: Tuesday: Saturday: Holiday 1: o On R Off Holiday 3: o On R Off 003 –...
Page 216 Section 7: Programming Worksheets 007 – Partition 26 No Activity Arming Pre-Alert Timer (Default: 001): [177] Partition 27 Auto-Arm/Disarm 001 – Partition 27 Auto-Arming Times: 24-Hour: Wednesday: (4-digit HH:MM) Sunday: Thursday: Default: 9999 Monday: Friday: Tuesday: Saturday: 002 – Partition 27 Auto-Disarm Times: 24-Hour: Wednesday: (4-digit HH:MM)
Page 217 Section 7: Programming Worksheets Holiday 2: o On R Off Holiday 4: o On R Off (3-digit decimal) 004 – Partition 29 Auto-Arming Pre-Alert (Default: 004): 005 – Partition 29 Auto-Arming Postpone Timer (Default: 000): 006 – Partition 29 No Activity Arming Timer (Default: 000): 007 –...
Page 218: Partition And Zone Assignment
Section 7: Programming Worksheets (4-digit HH:MM) Sunday: Thursday: Default: 9999 Monday: Friday: Tuesday: Saturday: 003 – Partition 32 Auto-Disarming Holiday Schedule: Holiday 1: o On R Off Holiday 3: o On R Off Holiday 2: o On R Off Holiday 4: o On R Off (3-digit decimal) 004 –...
Page 219 Section 7: Programming Worksheets [201]-[232] Partition Zone Assignment (Description on page 123) o o o o o o o o o o o o o o o o 008 – 57-64 008 – 57-64 o o o o o o o o o o o o o o o o 009 –...
Page 220 Section 7: Programming Worksheets [201]-[232] Partition Zone Assignment (Description on page 123) o o o o o o o o o o o o o o o o 014 – 105-112 014 – 105-112 o o o o o o o o o o o o o o o o 015 –...
Page 221 Section 7: Programming Worksheets [201]-[232] Partition Zone Assignment (Description on page 123) o o o o o o o o o o o o o o o o 020 – 153-160 020 – 153-160 o o o o o o o o o o o o o o o o 021 –...
Page 222 Section 7: Programming Worksheets [201]-[232] Partition Zone Assignment (Description on page 123) o o o o o o o o o o o o o o o o 026 - 201-208 026 - 201-208 o o o o o o o o o o o o o o o o 027 - 209-216 027 - 209-216...
Page 223 Section 7: Programming Worksheets [201]-[232] Partition Zone Assignment (Description on page 123) [211] Partition 11 Zone Assignment [212] Partition 12 Zone Assignment o o o o o o o o o o o o o o o o 001 – 01-08 001 –...
Page 224 Section 7: Programming Worksheets [201]-[232] Partition Zone Assignment (Description on page 123) o o o o o o o o o o o o o o o o 004 – 25-32 004 – 25-32 o o o o o o o o o o o o o o o o 005 –...
Page 225 Section 7: Programming Worksheets [201]-[232] Partition Zone Assignment (Description on page 123) o o o o o o o o o o o o o o o o 010 – 73-80 010 – 73-80 o o o o o o o o o o o o o o o o 011 –...
Page 226 Section 7: Programming Worksheets [201]-[232] Partition Zone Assignment (Description on page 123) o o o o o o o o o o o o o o o o 016 – 121-128 016 – 121-128 o o o o o o o o o o o o o o o o 017 –...
Page 227 Section 7: Programming Worksheets [201]-[232] Partition Zone Assignment (Description on page 123) o o o o o o o o o o o o o o o o 022 - 169-176 022 - 169-176 o o o o o o o o o o o o o o o o 023 - 177-184 023 - 177-184...
Page 228 Section 7: Programming Worksheets [201]-[232] Partition Zone Assignment (Description on page 123) o o o o o o o o o o o o o o o o 028 - 217-224 028 - 217-224 o o o o o o o o o o o o o o o o 029 - 225-232 029 - 225-232...
Page 229 Section 7: Programming Worksheets [201]-[232] Partition Zone Assignment (Description on page 123) o o o o o o o o o o o o o o o o 001 – 01-08 001 – 01-08 o o o o o o o o o o o o o o o o 002 –...
Page 230 Section 7: Programming Worksheets [201]-[232] Partition Zone Assignment (Description on page 123) o o o o o o o o o o o o o o o o 005 – 33-40 005 – 33-40 o o o o o o o o o o o o o o o o 006 –...
Page 231 Section 7: Programming Worksheets [201]-[232] Partition Zone Assignment (Description on page 123) o o o o o o o o o o o o o o o o 011 – 81-88 011 – 81-88 o o o o o o o o o o o o o o o o 012 –...
Page 232: Communications
Section 7: Programming Worksheets [201]-[232] Partition Zone Assignment (Description on page 123) o o o o o o o o o o o o o o o o 016 – 121-128 016 – 121-128 o o o o o o o o o o o o o o o o 017 –...
Page 233 Section 7: Programming Worksheets [300] Panel/Receiver Communications Path Description on page 123 R PSTN-Phone Line 004 – Receiver 4: o Alt Comm Auto Routing o Alt Comm Receiver 1 - Ethernet o Alt Comm Receiver 2 - Ethernet o Alt Comm Receiver 3 - Cellular o Alt Comm Receiver 4 - Cellular [301] Phone Number Programming (Default: DFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF)
Page 234 Section 7: Programming Worksheets R R R R R R o o R R R R R R o o R R R R R R o o R R R R R R o o R R R R R R o o 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8...
Page 235 Section 7: Programming Worksheets R R R R R R o o R R R R R R o o R R R R R R o o R R R R R R o o R R R R R R o o 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8...
Page 236 Section 7: Programming Worksheets R R R R R R o o R R R R R R o o R R R R R R o o R R R R R R o o R R R R R R o o 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8...
Page 237 Section 7: Programming Worksheets [308] Event Reporting Description on page 124 R1 – Duress Alarm 001 – Miscellaneous Alarm 1 R 2 – Opening After Alarm R 3 – Recent Closing Alarm R 4 – Zone Expander Supervisory Alarm R 5 – Zone Expander Supervisory Alarm Restore R6 –...
Page 238 Section 7: Programming Worksheets [308] Event Reporting Description on page 124 R1 – Panel AC Fail Trouble 301 – Panel Events 1 R2 – Panel AC Fail Restore R 3 – Panel Low Battery Trouble R 4 – Panel Low Battery Trouble Restore R 5 –...
Page 239 Section 7: Programming Worksheets [308] Event Reporting Description on page 124 R2 – Receiver 1 FTC Restore 321 – Receiver Events R4 – Receiver 2 FTC Restore R6 – Receiver 3 FTC Restore R8 – Receiver 4 FTC Restore R1 – Module AC Trouble 331 –...
Page 240: Call Directions
Section 7: Programming Worksheets [308] Event Reporting Description on page 124 R1 – Device AC Fail 361 – Wireless Device Events R2 – Device AC Restore R 3 – Device Low Battery R 4 – Device Low Battery Restore R 5 – Device Fault R 6 –...
Page 241 Section 7: Programming Worksheets 001 – Partition 1 Alarm/ Restore: R Receiver #1 RReceiver #3 R Receiver #2 RReceiver #4 R Receiver #1 R Receiver #3 002 – Partition 1 Tamper/ Restore: R Receiver #2 R Receiver #4 oReceiver #1 o Receiver #3 003 –...
Page 242 Section 7: Programming Worksheets 001 – Partition 7 Alarm/ Restore: R Receiver #1 RReceiver #3 RReceiver #2 RReceiver #4 R Receiver #1 RReceiver #3 002 – Partition 7 Tamper/ Restore: RReceiver #2 RReceiver #4 o Receiver #1 o Receiver #3 003 –...
Page 243 Section 7: Programming Worksheets 001 – Partition 13 Alarm/ Restore: R Receiver #1 RReceiver #3 RReceiver #2 R Receiver #4 R Receiver #1 R Receiver #3 002 – Partition 13 Tamper/ Restore: R Receiver #2 RReceiver #4 o Receiver #1 o Receiver #3 003 –...
Page 244 Section 7: Programming Worksheets 001 – Partition 19 Alarm/ Restore: R Receiver #1 RReceiver #3 RReceiver #2 R Receiver #4 R Receiver #1 R Receiver #3 002 – Partition 19 Tamper/ Restore: R Receiver #2 RReceiver #4 o Receiver #1 o Receiver #3 003 –...
Page 245 Section 7: Programming Worksheets 001 – Partition 25 Alarm/ Restore: R Receiver #1 RReceiver #3 RReceiver #2 R Receiver #4 R Receiver #1 R Receiver #3 002 – Partition 25 Tamper/ Restore: R Receiver #2 RReceiver #4 o Receiver #1 o Receiver #3 003 –...
Page 246 Section 7: Programming Worksheets 001 – Partition 31 Alarm/ Restore: R Receiver #1 RReceiver #3 RReceiver #2 R Receiver #4 R Receiver #1 R Receiver #3 002 – Partition 31Tamper/ Restore: R Receiver #2 RReceiver #4 o Receiver #1 o Receiver #3 003 –...
Page 247 Section 7: Programming Worksheets 004 – Periodic Test Transmission Time of Day (Default: 9999): 011 – Maximum Dialing Attempts: (Default: 005): 012 – Delay Between PSTN Attempts: (Default: 003 seconds): 013 – Delay Between Force Attempts: (Default: 020 seconds): 014 – Post Dial Wait for Handshake: (Range: 001-255; Default: 040 Seconds; UL=45): 015 –...
Page 248: Dls Programming
Section 7: Programming Worksheets 1 –oTalk/Listen on Receiver 1 Description on page 136 2 –oTalk/Listen on Receiver 2 3 –oTalk/Listen on Receiver 3 4 –oTalk/Listen on Receiver 4 7.13 DLS Programming [401] DLS/SA Options Description on page 136 1 – o Double Call 2 –...
Page 249: Virtual Inputs
Section 7: Programming Worksheets 7.14 Virtual Inputs [560] Virtual Inputs (3 digit decimal) 001 - Virtual Input 1: 017 - Virtual Input 17: Description on page 138 002 - Virtual Input 2: 018 - Virtual Input 18: 003 - Virtual Input 3: 019 - Virtual Input 19: Default: 000 004 - Virtual Input 4:...
Page 250 Section 7: Programming Worksheets 301 – Start Time: 302 – End Time: Interval 3 303 – Days Assignment: 304 – Holiday Assignment: 01 – o Sunday o Holiday 1 (4- digit decimal) 02 – o Monday o Holiday 2 HH:MM 03 –...
Page 251 Section 7: Programming Worksheets Default: 0000 04 – o Wednesday o Holiday 4 05 – o Thursday 06 – o Friday 07 – o Saturday 401 – Start Time: 402 – End Time: Interval 4 403 – Days Assignment: 404 – Holiday Assignment: (4- digit decimal) 01 –...
Page 252 Section 7: Programming Worksheets 403 – Days Assignment: 404 – Holiday Assignment: 01 – o Sunday o Holiday 1 (4- digit decimal) 02 – o Monday o Holiday 2 HH:MM 03 – o Tuesday o Holiday 3 to HH:MM 04 – o Wednesday o Holiday 4 Default: 0000 05 –...
Page 253 Section 7: Programming Worksheets 05 – o Thursday 06 – o Friday 07 – o Saturday [711] Holiday Group 1 (6-Digit Decimal) 001 – Holiday Group 1 Date 1: MMDDYY 002 – Holiday Group 1 Date 2: Default: 000000 003 – Holiday Group 1 Date 3: 004 –...
Page 254: Audio Module Programming
Section 7: Programming Worksheets Description on 006 – Holiday Group 4 Date 6: page 139 007 – Holiday Group 4 Date 7: 008 – Holiday Group 4 Date 8: 009-099 – Holiday Group 4 Date 9-99: 7.16 Audio Module Programming [802] Audio Module Programming 2-digit entry 00= No station assigned...
Page 255 Section 7: Programming Worksheets Zone 32 Station Assignment: Zone 33 Station Assignment: Zone 34 Station Assignment: Zone 35 Station Assignment: Zone 36 Station Assignment: Zone 37 Station Assignment: Zone 38 Station Assignment: Zone 39 Station Assignment: Zone 40 Station Assignment: Zone 41 Station Assignment: Zone 42 Station Assignment: Zone 43 Station Assignment:...
Page 256 Section 7: Programming Worksheets Zone 74 Station Assignment: Zone 75 Station Assignment: Zone 76 Station Assignment: Zone 77 Station Assignment: Zone 78 Station Assignment: Zone 79 Station Assignment: Zone 80 Station Assignment: Zone 81 Station Assignment: Zone 82 Station Assignment: Zone 83 Station Assignment: Zone 84 Station Assignment: Zone 85 Station Assignment:...
Page 257 Section 7: Programming Worksheets Zone 116 Station Assignment: Zone 117 Station Assignment: Zone 118 Station Assignment: Zone 119 Station Assignment: Zone 120 Station Assignment: Zone 121 Station Assignment: Zone 122 Station Assignment: Zone 123 Station Assignment: Zone 124 Station Assignment: Zone 125 Station Assignment: Zone 126 Station Assignment: Zone 127 Station Assignment:...
Page 258 Section 7: Programming Worksheets Zone 158 Station Assignment: Zone 159 Station Assignment: Zone 160 Station Assignment: Zone 161 Station Assignment: Zone 162 Station Assignment: Zone 163 Station Assignment: Zone 164 Station Assignment: Zone 165 Station Assignment: Zone 166 Station Assignment: Zone 167 Station Assignment: Zone 168 Station Assignment: Zone 169 Station Assignment:...
Page 259 Section 7: Programming Worksheets Zone 200 Station Assignment: Zone 201 Station Assignment: Zone 202 Station Assignment: Zone 203 Station Assignment: Zone 204 Station Assignment: Zone 205 Station Assignment: Zone 206 Station Assignment: Zone 207 Station Assignment: Zone 208 Station Assignment: Zone 209 Station Assignment: Zone 210 Station Assignment: Zone 211 Station Assignment:...
Page 260 Section 7: Programming Worksheets Zone 242 Station Assignment: Zone 243 Station Assignment: Zone 244 Station Assignment: Zone 245 Station Assignment: Zone 246 Station Assignment: Zone 247 Station Assignment: Zone 248 Station Assignment: [802] 2-Way Audio Trigger Option 1 1 - o Tampers 2 - o Future Use 3 - R [A] Key Alarm 4 - R [P] Key Alarm...
Page 261 Section 7: Programming Worksheets Answering Machine Bypass: 2-digit entry Default: 00 Double Call Timer: 2-digit entry Default: 30 Number of Rings to Answer: 2-digit entry Default: 00 Audio Duration: 2-digit entry Default: 90 Record Time: 3-digit entry Default: 105 Erase Time: 2-digit entry Default: 15 minutes 1 - o Audio Station 1 Tamper...
Page 262: Wireless Programming
Section 7: Programming Worksheets 7.17 Wireless Programming [804] Wireless Programming 000 – WLS Device Enrollment Zones: (Selection) Zone #: This section is an overview of wireless device programming. See the Zone Definition: associated device installation sheets and the HSM2HOST/RFK (2-digit decimal) Partition Assignment: keypad installation instructions for detailed worksheets.
Page 263 Section 7: Programming Worksheets [004] Receiver Supervision Interval Default (00087/135) Valid range: 00000 - 65535 o 1 - Receiver 1 Supervised [005] System Toggle Options 1 o 2 - Receiver 3 Supervised o 3 - Heartbeat 1 o 4 - Cell Primary R 6 - Remote Firmware Upgrade o 7 –...
Page 264 Section 7: Programming Worksheets [020] Time Zone Default (00) Valid range: 00 - 99 Reporting codes [025] Radio Activation Restore Default (FF) Program 00 disable or FF enable [026] Receiver 1 Test Transmission Default (FF) Program 00 disable or FF enable [027] Receiver 2 Test Transmission Default (00) Program 00 disable or FF enable...
Page 265 Section 7: Programming Worksheets [102] Receiver 1 DNIS Default (000000) Valid range: 000000 - FFFFFF [103] Receiver 1 IP Address Default (127.000.000.001) [104] Receiver 1 UDP Remote Port Default (03061) Valid range: 00000 - 65535 [105] Receiver 1 UDP Local Port Default (03060) Valid range: 00000 - 65535 [106] Receiver 1 Domain Name...
Page 266 Section 7: Programming Worksheets [204] Receiver 3 Port Default (03061) Valid range: 00000 - 65535 [205] Receiver 3 APN Default ( ) 32 ASCII characters [206] Receiver 3 Domain Name Default ( ) 32 ASCII characters Cellular receiver 4 configuration [211] Receiver 4 Account Code Default (0000000000) Valid range: 0000000001 - FFFFFFFFFE [212] Receiver 4 DNIS...
Page 267 Section 7: Programming Worksheets [228] Voice Call Back Time Default (010) Valid entries from 000 to 255 [229] Voice Call Back Number Default ( ) 32 digit phone number. Valide entries:: 000000000000000 to FFFFFFFFFFFFFFF Integration session 1 [422] Integration Identification Number Default (MAC/IMEI) Read only [423] Session 1 Integration Access Code Default (12345678123456781234567812345678)
Page 268 Section 7: Programming Worksheets [432] Session 1 Integration Outgoing Port Default (03070) Valid range: 00000- 65535 [433] Session 1 Integration Incoming Port Default (03071) Valid range: 00000- 65535 Integration sessions 2-4 [450] - [460] Repeats [423] - [433] for Session 2 [477] - [487] Repeats [423] - [433] for Session 3 [504] - [514] Repeats [423] - [433] for Session 4 Notification controls...
Page 269 Section 7: Programming Worksheets R1 – Alarm and Alarm Restore Notifications [694] Session 4 Notification Control R2 –Tamper and Tamper Restore Notifications R3 – Arming and Disarming Notifications R4 – Trouble and Trouble Restore Notifications R5 – Test Transmission Notifications R6 –...
Page 270: Keypad Programming
Section 7: Programming Worksheets [996] Cellular Telephone Number This number is required for DLS and Firmware upgrades [997] IMEI Number [998] MAC Address [999] Software Default (00 - Factory Default Setting; 55 - Reset / Power Cycle) 7.19 Keypad Programming [860] Display Keypad Slot Number [861]-[892] Keypad Programming Refer to the installation instructions provided with the keypad for details.
Page 271 Section 7: Programming Worksheets 00 - Null Key 32 - Bypass Mode 74 - Partition Select 14 02 - Instant Stay Arm 33 - Bypass Recall 75- Partition Select 15 03 - Stay Arm 34 - User Programming 76- Partition Select 16 04 - Away Arm 35 - User Functions 77- Partition Select 17...
Page 272: Template Programming
Section 7: Programming Worksheets 031 – Downloaded LCD Message Duration (3-digit decimal; 000-255; Default: 000): 041 – Indoor Temperature Zone Entry (3-digit decimal; 000-248; Default: 000): 042 – Outdoor Temperature Zone Entry (3-digit decimal; 000-248; Default: 000): 00 – o Disabled 101-228 –...
Page 273: Module Programming
Section 7: Programming Worksheets 000 – Control Panel Version 001- 032 – View Keypad 1-32 Version 101-116 – HSM2108 8 Zone Module 1-15 Version 201-215 – HSM2208 8 Output Module 1 Version 301-315 – HSM3408 8 I/O Expansion Module 460 – Alternate Communicator 461 –...
Page 274: Wireless Placement Testing
Section 7: Programming Worksheets 7.23 Wireless Placement Testing Testing [904] Wireless Placement Test Description on page 158 001-248 – Placement Test - Zone 1-248 521-528 – Placement Test Repeaters 1-8 551-558 – Placement Test Sirens 1-8 601-632 – Placement Test Wireless Keys 1-32 701-716 –...
Page 275 Section 7: Programming Worksheets [904] Wireless Placement Test Description on page 158 022 – Zone Soak Test Assignment - Zones 169-176 023 – Zone Soak Test Assignment - Zones 177-184 024 – Zone Soak Test Assignment - Zones 185-192 025 – Zone Soak Test Assignment - Zones 193-200 026 –...
Page 276: Battery Settings
Section 7: Programming Worksheets 7.24 Battery Settings [982] Battery Settings Description on page 160 01 – o Panel High Charge Current 000 – Panel Battery Settings 01 – o HSM2204 1 High Charge Current 010 – HSM2204 High Current Output Battery 02 –...
Page 277: Restoring Factory Defaults
Section 7: Programming Worksheets 7.25 Restoring Factory Defaults (Descriptions on page 160) [989] Default Master Code [990] Installer Lockout Enable/Disable [991] Default Keypads 999 – Default All Keypads 901-932 – Default Keypad 1-32 [993] Default Alternate Communicator [996] Default HSM2HOST Wireless Receiver [988] Default HSM2955 [999] Default System - 277 -...
Page 278: Section 8: Troubleshooting
Section 8: Troubleshooting Section 8: Troubleshooting 8.1 Testing Power up system Program options as required (See "Programming descriptions" on page 84) Manually trip then restore zones Verify correct reporting codes are sent to the central station 8.2 Troubleshooting LCD programmable-message keypad: Press [*][2] followed by access code if required to view a trouble condition The trouble light flashes and the LCD displays the first trouble condition Use the arrow keys to scroll through all trouble conditions present on the system...
Page 279 Section 8: Troubleshooting Trouble Detailed Trouble 07 – Device Tampers 01 – Zone 1-248 04 – Repeater 1-8 03 – Siren 1-16 05 – Audio Station 01 - 04 08 – RF Delinquency 01 – Zone 1-248 03 – Siren 1-16 02 –...
Page 280 Section 8: Troubleshooting Trouble [1] Service Required Press [01] to determine specific trouble Trouble Troubleshooting [06] USB Wi-Fi Connected The trouble automatically clears once the HSM3WIFI adapter is unplugged from the panel. This trouble serves as a warning as to not to forget to unplug the adapter when configuration HSM3WIFI USB to Wi-Fi Adapter is plugged into the panel via Wi-Fi is completed.
Page 281 Section 8: Troubleshooting Trouble [2] Module Battery Trouble Press [02] to determine specific trouble Trouble Troubleshooting [08] Power Supply 1-4 No Battery (HSM2300) Verify battery is connected. Enter 08 to view which HSM2300 does not have a Ensure battery leads are connected with the right polarity. battery connected.
Page 282 Section 8: Troubleshooting Trouble [3] Bus Voltage Trouble Press [03] to determine specific trouble Trouble Troubleshooting [01] HSM2HOST Bus Low Voltage Ensure voltage at module is higher than the documented limits. The 2-way wireless integration module has detected a Ensure wire run is not too long. voltage less than 6.3V on its aux input.
Page 283 Section 8: Troubleshooting Trouble [4] AC Failure Press [04] to determine specific trouble Trouble Troubleshooting [01] Zone 1-248 AC Verify voltage measured across DC input terminals is 16-20VDC. Replace HSM65W power adapter if required. [03] Siren 1-16 AC For the HSM2204 or HSM2300 modules, ensure a 40VA 16.5VAC transformer [04] Repeater 1-8 AC is being used.
Page 284 Section 8: Troubleshooting Trouble [05] Device Faults Press [05] to determine specific trouble Trouble Troubleshooting [10] Freeze trouble Move the device to a location with room temperature and ensure the trouble clears. If not check the programming threshold for low temperature for the zone. Enter 08 to view the wireless zone which is detecting high temperature.
Page 285 Section 8: Troubleshooting Trouble [9] Module Supervisory Press [09] to determine specific zones with a tamper trouble Trouble Troubleshooting [01] HSM2HOST Ensure the module is physically connected to the corbus. [02] Keypad 1-30 Measure power across corbus Red and Blk directly on the module and ensure it is at 10.5V (min).
Page 286 Section 8: Troubleshooting Trouble [11] Communications Press [11] to determine specific trouble Trouble Troubleshooting [04] Alternate Comm Cellular Check the the event buffer for trouble details. The alternate communicator has detected a radio or For radio/SIM failure, ensure the cellular plug-in module is connected to the SIM failure, a cellular network trouble, or insufficient panel properly and that the SIM card is correctly inserted in the right signal strength.
Page 287 Section 8: Troubleshooting Trouble [12] Not Networked Press [12] to toggle through troubles Trouble Troubleshooting [01] Zones 1-248 Ensure the device is physically present. [02] Keypad 1-32 Check the current signal strength and during the last 24 hours. [03] Siren 1-16 Replace the battery or press the tamper switch.
Page 288: Appendix 1: Reporting Codes
Appendix 1: Reporting codes Appendix 1: Reporting codes The following tables contain Contact ID and Automatic SIA format reporting codes. See "[308] Event Reporting" on page 124 for event reporting codes. 1.1 Contact ID Each of the digits indicate specific information about the signal. For example, if zone 1 is an entry/exit point, the event code contains [34].
Page 289 Appendix 1: Reporting codes Section # Definition Dialer Automatic Contact ID SIA Auto Rep Codes** Direction* Codes [308]-[101] HSM3204CX: Corbus repeater module #1-8 E(3)41-(801-816) ES-(0801-0816) tamper/restored R(3)41-(801-816) EJ-(0801-0816) [308]-[101] HSM3350: 3A Power supply module #1-4 tamper/restored E(3)41-(651-654) ES-(0651-0654) R(3)41-(651-654) EJ-(0651-0654) [308]-[101] Keypad Lockout - Incorrect access code entry E(4)61-000...
Page 290 Appendix 1: Reporting codes Section # Definition Dialer Automatic Contact ID SIA Auto Rep Codes** Direction* Codes [308]-[332] Hardwired Module Low Voltage trouble/restore - MA/R E (3)AA-551 EM-0551 HSM2HOST R (3)AA-551 EN-0551 [308]-[332] Hardwired Module Low Voltage trouble/restore - HSM2204 MA/R E(3)AA-601-604 EM-0601-0601...
Page 291 Appendix 1: Reporting codes Section # Definition Dialer Automatic Contact ID SIA Auto Rep Codes** Direction* Codes [308]-[331] HSM2204 1-4 Battery absent trouble/restore MA/R E(3)11-601-604 YM-0601-0604 R(3)11-601-604 YR-0601-0604 [308]-[331] HSM2300 1-4 Battery absent trouble/restore MA/R E(3)11-621-624 YM-0621-0624 R(3)11-621-624 YJ-0621-0624 [308]-[331] HSM3204CX 1-16 Battery 1 or 2 absent /restore MA/R E(3)11-801-816...
Page 292 Appendix 1: Reporting codes Section # Definition Dialer Automatic Contact ID SIA Auto Rep Codes** Direction* Codes [308]-[361] Wireless Device Low Battery trouble/restore. MA/R E(3)84-ZZZ XT-ZZZZ ZZZ= 601-616: wireless keypads R(3)84-ZZZ XR-ZZZZ 701-732: wireless keys 801-816: wireless Sirens 901-908: wireless repeaters [308]-[361] Wireless Zone AC trouble/restore MA/R...
Page 293 Appendix 1: Reporting codes Section # Definition Dialer Automatic Contact ID SIA Auto Rep Codes** Direction* Codes [308]-[011] [F] Key alarm/restore E(1)1A-000 FA-0000 / FH-0000 R(1)1A-000 [308]-[011] [M] Key alarm/restore E(1)AA-000 MA-0000 / MH-0000 R(1)AA-000 [308]-[011] [P] Key alarm/restore E(1)2A-000 PA-0000 / PH-0000 R(1)2A-000 [308]-[011]...
Page 294: Contact Id & Sia Zone Alarm/Restore Event Codes
Appendix 1: Reporting codes Section # Definition Dialer Automatic Contact ID SIA Auto Rep Codes** Direction* Codes [308]-[313] Panel firmware update begin/ successful MA/R E(9)01-900 LB-0900 R(9)01-900 LS-0900 [308]-[313] Panel firmware update fail MA/R E(9)02-900 LU-0900 [308]-[313] Radio firmware update begin/successful MA/R E(9)03-902 LB-0000...
Page 295 Appendix 1: Reporting codes Zone Definition SIA Auto Rep Codes Contact ID Auto Rep Codes Maintained Keyswitch Disarm (Walk Test Only) BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ 24-Hr. Supervisory US-ZZZZ / UR-ZZZZ E(1) 5A - ZZZ / R(1)5A - ZZZ 24-Hr.
Page 296: Appendix 2: Word Library
Appendix 2: Word library Appendix 2: Word library Aborted Access Active Activity Alarm Area Armed Arming Attic Auxiliary Away Baby Back Basement Bathroom Battery Bedroom Bonus Bottom Breezeway Building Bypass Bypassed Cabinet Camera Canceled Carbon Central Chime Closed Closet Closing Code Communicator Computer...
Page 297: Appendix 3: Template Programming Tables
Appendix 3: Template programming tables Appendix 3: Template programming tables The following tables show the programming options for template programming digits 1-5. 3.1 Digit 1 – Zones 1-8 Definition Options Note: A “0” in the digit 1 location indicates that the first 8 zones use the panel default zone definitions. Option Zone 1 Zone 2...
Page 298 Appendix 3: Template programming tables Entry Template Programming Receiver 1 SIA, Receiver 2 CID with backup [380] Comm Toggles 1 - Bit 1 Communications Enabled - On [350] Communicator Formats - [001] Receiver 1 - 03 CID [350] Communicator Formats - [002] Receiver 2 - 04 SIA [350] Communicator Formats - [003] Receiver 3 - 04 SIA [350] Communicator Formats - [004] Receiver 4 - 04 SIA [384] Comm Backup - Bit 2 Receiver 2 Backup - On...
Page 299: Digit 4 - Reporting Code Configuration Options
Appendix 3: Template programming tables Entry Template Programming Receiver 1 and 2 CIA with backup [380] Comm Toggles 1 - Bit 1 Communications Enabled - On [350] Communicator Formats - [001] Receiver 1 - 03 CID [350] Communicator Formats - [002] Receiver 2 - 03 CID [350] Communicator Formats - [003] Receiver 3 - 03 CID [350] Communicator Formats - [004] Receiver 4 - 03 CID [384] Comm Backup - Bit 2 Receiver 2 Backup - On...
Page 300 Appendix 3: Template programming tables Common Group Common Group Programming Test transmission call directions disabled [309][002] Test Transmission - Bit 1 Receiver 1 - Off [309][002] Test Transmission - Bit 2 Receiver 2 - Off [309][002] Test Transmission - Bit 3 Receiver 3 - Off [309][002] Test Transmission - Bit 4 Receiver 4 - Off Enables/Disables all Reporting Codes Selected Troubles - Enables the following Troubles...
Page 301: Digit 5 - Dls Connection Options
Appendix 3: Template programming tables Zone Alarm Restore Group DLS/Installer Lead In/Out Programming Restore zone alarm reporting codes [307][001] - Bit 2 Alarm Restore - Off [307][002] - Bit 2 Alarm Restore - Off [307][003] - Bit 2 Alarm Restore - Off [307][004] - Bit 2 Alarm Restore - Off [307][005] - Bit 2 Alarm Restore - Off [307][006] - Bit 2 Alarm Restore - Off...
Page 302 Appendix 3: Template programming tables i. Program the required DLS access code. All 6 digits must be entered in order to complete your entry. ii. This access code is entered into programming section [403]. 5. Entry Delay 1 and Exit Delay i.
Page 303: Appendix 4: Ascii Characters
Appendix 4: ASCII Characters Appendix 4: ASCII Characters “ & ‘ < > ￥ ╲ 100 101 102 103 104 ‫׀‬ → ← 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 160 「...
Page 304: Appendix 5: Regulatory Approvals
Appendix 5: Regulatory approvals Appendix 5: Regulatory approvals 5.1 FCC COMPLIANCE STATEMENT Caution: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 305: Innovation, Scientific And Economic Development Canada (Ised) Statement
Appendix 5: Regulatory approvals Equipment Maintenance Facility If trouble is experienced with this equipment HS3032/HS3128/HS3248 for repair or warranty information, please contact the facility indicated below. If the equipment is causing harm to the telephone network, the Telephone Company may request that you disconnect the equipment until the problem is solved.
Page 306 Appendix 5: Regulatory approvals ULC-S559-13 Equipment for Fire Signal Receiving Centers and Systems ULC-S545-02 Residential Fire Warning System Control Units The subscriber control unit shall provide for the connection of protective wiring, conductors, and attachments in accordance with the Standard for Installation and Classification of Burglar and Holdup Alarm Systems, UL 681. This product has also been tested and found in compliance with the ANSI/SIA CP-01-2014 Control Panel Standard –...
Page 307 Appendix 5: Regulatory approvals Wireless Supervision window shall be set to 24 hours for Burglary Installations only (Wireless Programming, section [804]> [802] shall be programmed with the value 96) RF Jam detection shall be enabled (refer to Wireless Programming (section [804][801], option 00 shall be OFF) New Alarms will Disconnect 2-way Audio (section [022], option 6 OFF) Requirements for UL985 6th edition compliant installations: For UL residential fire applications (including CO) compliant with UL985 6th edition, the following guidelines shall be respected:...
Page 308 Appendix 5: Regulatory approvals The bell timeout shall be programmed for 15 minutes minimum. At least one system remote keypad with tamper switch shall be employed The integral communciator (DACT/IP) or plug-in cellular module shall be enabled and shall be programmed to provide a low battery transmission.
Page 309: Sia False Alarm Reduction Installations: Quick Reference
Appendix 5: Regulatory approvals Bell Location The alarm sounding device (bell) shall be located where it can be heard by the person operating the security system during the daily arming and disarming cycle. Protection of the Control Unit The local control unit and the local power supply must be protected in one of the following ways: The control unit and audible alarm device must be in a protected area which is armed 24 hours a day.
Page 310 Appendix 5: Regulatory approvals Table 5-1: SIA quick reference SIA Feature Programming Comments Range/Default Requirement Section Exit Time Access to Entry and Exit delays and Bell Time Out for the Range:45- 255 Required system. seconds [005]>[001], option 3 (programmable) Default: 60 sec. Exit Delay Restart Opening a Delay zone door after it has already been opened Default:...
Page 311: European En50131 Compliance Statement
Appendix 5: Regulatory approvals SIA Feature Programming Comments Range/Default Requirement Section Cross Zoning Enables cross zoning for entire system. Zones can be Programming Required enabled for cross zoning via zone attribute option 8 in required [042]>Selection 3, option 002 sections [002][101] - [248]. Default: Disabled Burglary Verification Timer...
Page 312 Appendix 5: Regulatory approvals EN50136-2:2013 Grade 2, Class II, ATS SP3 (dialer), SP4 (Ethernet), DP2 (dialer and Ethernet), DP3 (Ethernet and plug-in cellular) when installed in enclosure models HSC3020CP. This product is suitable for use in systems with the following notification options: - A - use of two remotely powered warning devices and one ATS SP3 required (internal dialer or ethernet or plug-in cellular module) - B - use of one self-powered warning device and one ATS SP3 required (internal dialer or ethernet or plug-in cellular module) - C - use of dual path ATS DP2 required (any combination of internal dialer and ethernet and/or cellular module)
Page 313: Compliance Statement
Appendix 5: Regulatory approvals The product is labelled with the CE mark as proof of compliance with the above mentioned European Directives. Also, a CE declaration of conformity (DoC) for this product can be found at www.dsc.com under the Agency Listings section. Additional notes for EN50131 compliant installations The alarm system can be set/unset with 6 or 8-digit user access codes, or using compatible wireless keys.
Page 314 Appendix 5: Regulatory approvals The HS3032, HS3128 and HS3248 are capable of supporting the completion of the full setting procedure by one of the following methods: a) push button switch mounted outside the supervised premises. Instructions to be provided for the zone type to be programmed for the key arming;...
Page 315: Appendix 6: Ul/Ulc Wiring Diagram
Appendix 6: UL/ULC Wiring Diagram Appendix 6: UL/ULC Wiring Diagram 6.1 HS3032, HS3128, and HS3248 UL/ULC wiring diagram (North America only) APPLICABLE UL STANDARDS UL File No. S4019 UL1610 Central Station Burglar Alalrm Units UA718 PC LINK UL365 Police Station Connected Burglar Alarm Units & Systems MICRO-B *AUX Wiring USB TYPE A...
Page 316: Appendix 7: Specifications
Appendix 7: Specifications Appendix 7: Specifications The following table outlines the specifications of the PowerSeries Pro alarm controller. Feature Description Zone configuration 32, 128, or 248 wireless zones. Up to 8 hardwired zones. 41 zone types. 15 programmable zone attributes. Normally closed, SEOL, DEOL, and TEOL resistor.
Page 317 Appendix 7: Specifications Feature Description Current draw - 120 mA (nominal). control panel board assembly Bell output 10.8 VDC to 12.5 VDC (UL/ULC applications). 10 VDC to 14 VDC (EN applications). 700 mA supervised (1 kΩ), current limited at 2 A. Steady, pulsed, temporal 3, or temporal 4 cadences.
Page 318 Appendix 7: Specifications Feature Description System AC power failure supervision Zone trouble Fire trouble Telephone line trouble Communicator trouble Low battery condition RF jam AUX power supply fault Failure to communicate Module fault (supervisory or tamper) System overcurrent Additional 2-way wireless device support Visual verification (images + audio)* Proximity tag support PGM scheduling...
Page 319: Appendix 8: Locating Detectors And Escape Plan
Appendix 8: Locating detectors and escape plan Appendix 8: Locating detectors and escape plan 8.0 Locating detectors and escape plan The following information is for general guidance only, consult local fire codes and regulations when locating and installing smoke and CO alarms. 8.1 Smoke Detectors Research has shown that all hostile fires in homes generate smoke to a greater or lesser extent.
Page 320: Fire Escape Planning
Appendix 8: Locating detectors and escape plan 8.2 Fire Escape Planning There is often very little time between the detection of a fire and the time it becomes deadly. It is thus very important that a family escape plan be developed and rehearsed. 1.
Page 321: Appendix 9: New Features Listing
Appendix 9: New Features Listing Appendix 9: New Features Listing Version 1.2 Support for 32 keypads and 32 partitions for HS3248 model Support for 30 HSM3408 modules Support 32 HS2TCH keypads Support for 16 HS2LCDWF keypads Support for 16 HSM3204CX modules for the HS3248 panel Communicator installer code added for option [851][011] Native support for PGx309 Support for Alarm Install PSP and PowerManage end user app...
Page 322 Limited warranty Digital Security Controls (DSC) warrants the original purchaser that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use. During the warranty period, DSC shall, at its option, repair or replace any defective product upon return of the product to its factory, at no charge for labour and materials.
Page 323 Out of Warranty Repairs Digital Security Controls will at its option repair or replace out-of-warranty products which are returned to its factory according to the following conditions. Anyone returning goods to Digital Security Controls must first obtain an authorization number. Digital Security Controls will not accept any shipment whatsoever for which prior authorization has not been obtained.
Page 324 materials, overloaded electrical circuits, children playing with matches or arson. Even if the smoke detector operates as intended, there may be circumstances when there is insufficient warning to allow all occupants to escape in time to avoid injury or death. Motion Detectors Motion detectors can only detect motion within the designated areas as shown in their respective installation instructions.
Page 325 Software product license The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. The SOFTWARE PRODUCT is licensed, not sold. 1. GRANT OF LICENSE This EULA grants You the following rights: (a) Software Installation and Use - For each license You acquire, You may have only one copy of the SOFTWARE PRODUCT installed.
Page 326 7. LIMITED WARRANTY (a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT WARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIREMENTS OR THAT OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE. (b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible for problems caused by changes in the operating characteristics of the HARDWARE, or for problems in the interaction of the SOFTWARE PRODUCT with non-DSC-SOFTWARE or HARDWARE PRODUCTS.
Page 327 Product offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all products include all features. Availability varies by region; contact your sales representative. © 2020 Johnson Controls. All rights reserved. JOHNSON CONTROLS, TYCO and DSC are trademarks of Johnson Controls.

This manual is also suitable for:

Tyco powerseries pro hs3128 Tyco powerseries pro hs3248

Johnson Controls Tyco PowerSeries Pro HS3032 Reference Manual

Quick Links

Related Manuals for Johnson Controls Tyco PowerSeries Pro HS3032

Summary of Contents for Johnson Controls Tyco PowerSeries Pro HS3032

This manual is also suitable for:

Table of Contents