Wow SparkMaker Operating Manual page 52

©How to get a print model?
❶
Download the print file "print.wow"(for
version) file that can be printed directly from the official
❷
Download the STL file from the 3D Print Model website or convert the model file to the STL file format.
❸
Design the model using computer 3D design software and then export the model to a file in STL format.
©How to update the firmware?
❶
Download the latest update firmware from the official
❷
Unzip the downloaded update firmware update.wow (for
SparkMaker FHD version) and save it on the SD card.
❸
Turn off the power to SparkMaker.
❹ Insert the
SD card into the
SparkMaker
❺ Power on the
SparkMaker.
❻
The indicator on the knob will turn purple(if it is
knob will turn purple) , and then the light started flashing
❼
Use your computer to delete the update firmware from the SD card.
❽
Finish updating the firmware and start printing.
©How can I check if there is a problem with the print file?
Open the *.wow(for SparkMaker version)or *fhd(for
computer software and check if the pattern of each layer of the slice is normal.
©Why does the indicator change from green to red and then quickly change back to
green when the SD card is inserted and the knob is clicked?
❶ The SD card is not recognized or has been damaged. A new SD card needs to be replaced. The SD card
should be a C10 high-speed card with a capacity lower than 32GB. The file system format is FAT32. The SD
card is completely unlocked by hardware , and the metal contacts are free of stains.
❷ The direction or depth of the SD card insertion is incorrect. It needs to be adjusted to make the metal contacts
100
contact.
SparkMaker version)or "print.fhd" (for SparkMaker FHD
SparkMaker website (www.sparkmaker3d.com).
SparkMaker website (www.sparkmaker3d.com).
version) or update-FHD.wow (for
SparkMaker
card slot.
SparkMaker FHD version , you need click the knob when
, finally turn green , which means the update is successful.
SparkMaker FHD version) slice file with
❸ If you use the knob to control the printer
SparkMaker version)or "print.fhd" (for
be recognized.
❹ Open the print file with
©Why does the platform continue to drop without stopping after clicking the knob to
print?
❶ The platform is not leveled
been triggered , and the platform should be leveled first.
❷ There is residue on the platform or in the tank
switch has not been triggered. The residue on the platform and in the tank should be cleaned.
❸ The trigger piece on the platform is not aligned with the lower photoelectric switch. The trigger piece should be
inserted into the middle notch of the photoelectric switch.
❹ The photoelectric switch is damaged or the photoelectric switch is not installed correctly.
©Why is the screw movement not smooth?
❶ The Z axis is not corrected. The direction of the lead screw and the guide rail are not parallel
motion resistance and needs to be corrected again.
❷ The screw needs to add some grease.
❸ The screw is blocked by the cured resin and needs to be cleaned.
❹ The copper nut mounting screw is too tight
SparkStudio
adjusted to make the screw move smoothly.
©Why does the model need to add support?
The gravity and release force need to be overcome during the printing process. Therefore
the suspended part of each layer must be supported. In order to ensure that the model is not deformed and not
broken the model needs to add more support to strengthen the support structure to overcome the release force.
,
©What is the printing time of
, check if the print file named in the SD card is"print.wow"(for
SparkMaker FHD version). If other file names are used
SparkStudio and check if there is a problem with print file.
, so that it cannot be lowered to the lowest point. The photoelectric switch has not
, so that it cannot be lowered to the lowest point. The photoelectric
, the screw is stuck , and the copper nut mounting screw should be
SparkMaker SLA 3D printer?
, they will not
, which creates
, the minimum point and
101