Table of Contents
Advertisement
AUX SEND
LEFT
LEFT CHANNEL
gain L
in L
in R
gain R
RIGHT CHANNEL
AUX SEND
RIGHT
Fig. 9-11. Aux type: Aux + Mixer
When the Aux type is set to be one of the following configurations:
'LoopL>OutL', 'LoopR>OutR', 'LoopL&R>Out', then the AUX SEND/RETURN
jacks [16a to 16d] operate at instrument level.
If Aux type is set to 'AUX+ Mixer' the AUX SEND/RETURN jacks [16a to 16d]
operate at up to +7dBu (line level). To accommodate DSP units operating
at standard +4dBu the send signal levels can be individually adjusted using
parameters GsL, GsR (gain send level Left/Right ). Using the parameter WtL
and WtR (Wet Left/Right) the return signal levels are individually readjusted to
instrument level and mixed with the analog signals by means of the DrL, DrR
(Dry level Left/Right) parameters. GsL, GsR, WtL, WtR, DrL, DrR and Aux type
parameters are part of your preset definition and therefore are saved in the
preset (see next section).
When Aux type is selected to 'none' all the effects connected to the AUX
SEND/RETURN jacks [16a to 16d] are true bypassed.
PAGE 2/2 - AUX MIXER
When the loop routing parameter Aux type on page
Mixer', you can adjust on this page the settings of the auxiliary mixer, so as to
change how the sound of your PedalPro Ex is blended with that of your exter-
nal (stereo) effect.
Fig. 9-11
should help identifying the AUX mixer's param-
eters and their effect on the sound chain.
dry L
+
AUX RETURN
LEFT
external
wet L
stereo
effect
out L
out R
wet R
AUX RETURN
RIGHT
+
dry R
1/2
is set to 'Aux +
A x u m
i e x r
GsL: 030.
WtL: 0 0.
5
DrL: 015.
GsL – Gain level, send left channel. Range: 0-100%.
The GsL (Gain send left) parameter controls the level of gain applied to the
signal sent to the external effect via the AUX SEND LEFT jack [16a].
To adjust the amount of gain on the left send channel, press EDIT [5]. Use
•
the arrow keys [3] to position the blinking cursor next to GsL. Adjust the
value with the selection dial [4].
GsR – Gain level, send right channel. Range: 0-100%.
The GsL (Gain send right) parameter controls the level of gain applied to the
signal sent to the external effect via the AUX SEND RIGHT jack [16b].
To adjust the amount of gain on the right send channel, press EDIT [5].
•
Use the arrow keys [3] to position the blinking cursor next to GsR. Adjust
the value with the selection dial [4].
DrL – Dry level, left channel. Range: 0-100%.
The DrL (Dry left) parameter controls the amount of dry signal that is bypass-
ing the external effect on the left channel.
To adjust the amount of dry signal on the left channel, press EDIT [5]. Use
•
the arrow keys [3] to position the blinking cursor next to DrL. Adjust the
value with the selection dial [4].
DrR – Dry level, right channel. Range: 0-100%.
The DrR (Dry right) parameter controls the amount of dry signal that is bypass-
ing the external effect on the right channel.
•
To adjust the amount of dry signal on the right channel, press EDIT [5]. Use
the arrow keys [3] to position the blinking cursor next to DrR. Adjust the
value with the selection dial [4].
WtL – Wet level, left return channel. Range: 0-100%.
The WtL (Wet left) parameter controls the amount of wet signal coming from
the external effect into the left channel, via the AUX RETURN LEFT jack [16c].
49
Post Effects
È
2/3
1
G
sR: 0 3
0 .
1
5
W
tR: 5 2
0 .
0
2
D
rR: 0 1
0 .
1
9
9
Advertisement
Table of Contents
