Table of Contents
Advertisement
PAGE 4/6 - AUTO MODE MODULATION SETTINGS FOR F2
This page is used to configure filter F2 when auto mode is selected for F2
(F2Md set to auto on page 2/6).
W v a
e : 2 r t
F
ec
Tempo: 10 .
0 0
F in
m
2
[Hz 0 :
]
F ax
m
1
[Hz 1 :
]
WaveF2 – Filter F2 modulating waveform. Range: sine, trig, trap, rect, expo,
shl1, shl2, shl3.
This is the waveform assigned to the individual modulator of each filter. You
can choose from among the following possibilities (see
64, for more details on the modulating waveforms):
1.
sine = sinusoidal
2.
trig = triangle
3.
trap = trapezoidal
4.
rect = symmetric square waveform
5.
expo = exponential
6.
shl1 = shelf waveform 1
7.
shl2 = shelf waveform 2
8.
shl3 = shelf waveform 3
•
To change or select a modulating waveform for F2, press EDIT [5]. Use the
arrow keys [3] to position the blinking cursor next to WaveF2. Adjust the
value with the selection dial [4].
Tempo – Speed of the F2 modulator. Range 3 BPM (20 s) - 550 BPM (9.16 Hz)
•
To change the Tempo of the F2 modulating waveform, press EDIT [5]. Use
the arrow keys [3] to position the blinking cursor next to Tempo. Adjust
the value with the selection dial [4].
Ph – Phase of the F2 modulator. Range: 0°, 90°, 180°, 270°
Parameter Ph controls the phase of the modulating waveform. It is used to
control the relative phase of effects such as the Tremolo/Panner, Phaser, Fil-
ters (in auto mode), and Chorus, when used simultaneously. (For more details
È4/6
Ph: 0 0
0 Ì
1
0 5
3
0 0
Appendix
A, on page
refer to the QUICK TIP box
'Phase of the modulating
•
To alter the phase of the F2 modulator, press EDIT [5]. Use the arrow keys
[3] to position the blinking cursor next to Ph. Adjust the value with the
selection dial [4].
Fmin2 – F2 minimum frequency. Range: 150 Hz to 2697 Hz
Fmax2 – F2 maximum frequency. Range: 370 Hz to 2697 Hz
These values define the frequency range swept by filter F2 in auto mode
To change the value of Fmin2 or Fmax2, press EDIT [5]. Use the arrow keys
•
[3] to position the blinking cursor next to Fmin2 or Fmax2. Adjust the value
with the selection dial [4].
Please note: PedalPro Ex will NOT allow you to set Fmax2 smaller
than Fmin2.
PAGE 5/6 - ENVELOPE MODE MODULATION SETTINGS FOR F1 AND F2
This page is used to configure Filters F1 and F2 when in envelope mode (F1Md
and/or F2Md set to env+ or env- on
F t s
r [ 1 H :
Sens1: 02 .
F tr
s
2
[Hz 0 :
S ns
e
2
: 07 6 .
Fstr1[Hz] – Start frequency, filter F1. Range: 370 Hz to 1968 Hz
Sets the start frequency of the modulator sweep of filter F1 in envelope mode
•
To change the value of the starting frequency of the modulator of F1,
press EDIT [5]. Use the arrow keys [3] to position the blinking cursor next to
Fstr1. Adjust the value with the selection dial [4].
Sens1 – Sensitivity of filter F1. Range: 0-100%
This parameter defines how much the force you put into your strumming ac-
tion will affect the displacement of filter F1.
37
Working with Effects: Filters
waveforms', on page 29).
page
2/6).
z]
È5/6
0370
0 0
Fx: n i
l r
]
1
0 5
5
Fx: p x
e +
9
9
Advertisement
Table of Contents
