Edit Comm Settings (Hidden); Exit Menu - Extron electronics Annotator 300 User Manual

Edit Comm Settings (Hidden)

To display and enter this menu, press and hold the Input 3 button and the Next button
simultaneously. The hidden menu appears.
This menu allows the user to edit the following IP settings: DHCP Mode, IP Address,
Subnet Mask, and Gateway Address.

Exit Menu

At this menu, pressing Next exits the menu system and returns to the default cycle.
User Picture
Menu
Presets Control
Next
Next
Recall Preset
x: H Center V
<NA>
+00000 +00000
Rotate either to Rotate to adjust
select a preset to Horiziontal value
recall settings.
Rotate to adjust
Vertical value.
Next
Next
Save Preset
<02>
x: H Size V
+01365 +00768
Rotate either
to select a preset Rotate to adjust
to save current Horiziontal value
settings to. Rotate to adjust
Vertical value.
Next
x: Brit Cont
064* *064
Rotate to adjust
Brightness value
Rotate to adjust
Contrast value.
Next
x: Color Tint
064 064
Rotate to adjust
Color value
Rotate to adjust
Tint value.
Next
x: Detail
064*
Rotate either
to adjust Detail
value.
NOTE: In the images above, the term "x:" refers to an
input or an output number. For example, if selecting
input 2 with HDMI, for Input Configuration > Input Type,
the display reads:
NOTE: Press
Press
the Main menu.
*NOTE: To activate the hidden menu "Edit Comms",
press and hold
simultaneously.
Figure 9.
Input Output
Menu
Menu
Configuration
Configuration
Next
x: Resolution
x: Input Type
1024x1024 @60Hz
RGB
Rotate to select
video input type.
Next
x: Film Detect
<Off> On
HDMI Format
x: AUTO
Rotate to turn
Film Detect on
Rotate
or off.
output (1 or 2).
Next Rotate
format.
x: H Start V
128 128
x: HDCP Note
Rotate to adjust
<Off>
Vertical Start value.
Next
x: H Active V
1024* *768
Rotate to adjust
Horizontal Start value.
Next
x: Tpix Phase
1344* 16
Rotate to adjust
Pixel Phase value.
Next
x: EDID
1600x1200 @ 60Hz
Rotate to adjust
Total Pixel value
(* = default).
2: Input Type
HDMI
to cycle through the submenus.
to leave the current menu and go back to
and button
Annotator Menu System Overview
Menu Advanced
Menu
Configuration
Next Next
Test Pattern
Color Bars
Rotate to adjust
Rotate either to
Resolution value
select Test Pattern.
Rotate to adjust
Refresh rate.
Next
Next
Calibrate Panels
<NO> YES
Rotate either to
to select
select Yes or No.
to select
Next
Next
x: Auto Image
Off
On
Rotate either to turn
Aiuto Image on or off.
Rotate either to
turn Note on or off.
Next
x: Aspect Ratio
Fill
Rotate either to select
Aspect Ratio mode.
Next
x: Auto Memory
On
Rotate either to turn
Auto Memory on or off.
Next
Capture/Recall
USB
Rotate either to
select Capture/Recall
format.
Next
Overscan
S-video 5.0%
Rotate to select
video format.
Rotate to select
value.
Next
Switch Type
Fade
Rotate either to
select Switch Type
(cut or fade).
Next
Temperature
96 F 35 C
Indicates Internal temperature
(not adjustable).
Next
Factory Reset
Hold Auto Img
Press and hold Auto Image
to reset unit to factory settings.
Annotator 300 • Operation
View Comm
Exit Menu
Menu
Settings
Press NEXT
Next
Serial Port
9600 RS232
Next
MAC Address
005A6003C24
This is set at the factory
and cannot be changed
in "Edit Comm Settings"
menu.
Next
DHCP Mode
On
Next
IP Address
192.168.254.254
Next
Subnet Mask
255.255.000.000
Next
Gateway Address
000.000.000.000
"Hidden" Menu *
Edit Comm
Settings
Next
DHCP Mode
<On>
Rotate either to turn
DHCP mode On or Off.
Next
IP Address
<192>168.254.254
Rotate to select
octet field. Rotate
to change address.
Next
Subnet Mask
<255>255.000.000
Rotate to select
octet field. Rotate
to change address.
Next
Gateway Address
<000>000.000.000
Rotate to select
octet field. Rotate
to change address.
18