TANDBERG C90 System Integrator Manual page 58

Codec C90
Contents Introduction Getting Started
Contents Introduction Getting started
xConfiguration Network [1..1] IEEE8021X Eap Peap:
Protected Transport Layer Security. Developed by Microsoft, Cisco and RSA Security. Authenticates LAN
clients without the need for client certificates. EAP - Extensible Authentication Protocol. PEAP - Protected
Extensible Authentication Protocol.
On: The EAP-PEAP protocol is enabled. Default mode is On.
Off: The EAP-PEAP protocol is disabled.
Example:
xConfiguration Network 1 IEEE8021X Eap Peap: On
xConfiguration Network [1..1] IEEE8021X Eap TTLS:
Tunneled Transport Layer Security. Developed by Funk Software and Certicom. Usually supported by
Agere Systems, Proxim and Avaya. Authenticates LAN clients without the need for client certificates. EAP -
Extensible Authentication Protocol. TTLS - Tunneled Transport Layer Security.
On: The EAP-TTLS protocol is enabled. Default mode is On.
Off: The EAP-TTLS protocol is disabled.
Example:
xConfiguration Network 1 IEEE8021X Eap TTLS: On
xConfiguration Network [1..1] IEEE8021X Identity:
The 802.1X Identity is the user name needed for 802.1X authentication.
Format: String with a maximum of 64 characters.
Example:
xConfiguration Network 1 IEEE8021X Identity: ""
xConfiguration Network [1..1] IEEE8021X Mode:
The system may be connected to an IEEE 802.1X LAN network with a port-based network access control
that is used to provide authenticated network access for Ethernet networks.
On: The 802.1X authentication is enabled.
Off: The 802.1X authentication is disabled. Default mode is Off.
Example:
xConfiguration Network 1 IEEE8021X Mode: Off
xConfiguration Network [1..1] IEEE8021X Password:
The 802.1X Password is the password needed for 802.1X authentication.
Format: String with a maximum of 32 characters.
Example:
xConfiguration Network 1 IEEE8021X Password: "***"
xConfiguration Network [1..1] IPv4 Address:
Defines the Static IP address for the system. Only applicable if Static IP assignment is chosen.
Format: Compact string with a maximum of 64 characters.
Example:
xConfiguration Network 1 IPv4 Address: "10.47.5.100"
D14128.03—JULY 2009
Interfaces About the API
Interfaces About the API
<On/Off>
<On/Off>
<S: 0, 64>
<On/Off>
<S: 0, 32>
<S: 0, 64>
xConfiguration
xConfiguration xConfiguration xCommand
xCommand
xConfiguration Network [1..1] IPv4 Gateway:
Defines the IP default gateway. Only applicable if Static IP assignment is chosen.
Format: Compact string with a maximum of 64 characters.
Example:
xConfiguration Network 1 IPv4 Gateway: "10.47.5.100"
xConfiguration Network [1..1] IPv4 SubnetMask:
Defines the IP subnet mask. Only applicable if Static IP assignment is chosen.
Format: Compact string with a maximum of 64 characters.
Example:
xConfiguration Network 1 IPv4 SubnetMask: "255.255.255.0"
xConfiguration Network [1..1] IPv4 QoS Mode:
Defines whether IP Diffserv QoS should be used. The QoS (Quality of Service) is a method which
handles the priority of audio, video and data in the network. The QoS settings must be supported by the
infrastructure. DiffServ (Differentiated Services) is a computer networking architecture that specifies a
simple, scalable and coarse-grained mechanism for classifying, managing network traffic and providing
QoS priorities on modern IP networks.
Off: When set to Off no QoS method is used.
Diffserv: Select Diffserv and then go to the Diffserv sub-menus (Audio, Data, Signalling and Video) to
configure these settings.
Example:
xConfiguration Network 1 IPv4 QoS Mode: diffserv
xConfiguration Network [1..1] IPv4 QoS Diffserv Audio:
The DiffServ Audio setting is used to define which priority Audio packets should have in an IP network.
Enter a priority, which ranges from 0 to 63 for the packets. The higher the number, the higher the priority.
These priorities might be overridden when packets are leaving the network controlled by the local network
administrator.
Audio: A recommended value is DiffServ Code Point (DSCP) is AF41, which equals the value 34. If in doubt,
contact your network administrator.
Range: 0-63
Example:
xConfiguration Network 1 IPv4 QoS Diffserv Audio: 0
xConfiguration Network [1..1] IPv4 QoS Diffserv Data:
The DiffServ Data setting is used to define which priority Data packets should have in an IP network.
Enter a priority, which ranges from 0 to 63 for the packets. The higher the number, the higher the priority.
These priorities might be overridden when packets are leaving the network controlled by the local network
administrator.
Data: A recommended value is DiffServ Code Point (DSCP) AF23, which equals the value 22. If in doubt,
contact your network administrator.
Range: 0-63
Example:
xConfiguration Network 1 IPv4 QoS Diffserv Data: 0
System Integrator Guide
xStatus Cameras Appendices
xStatus Cameras Appendices
<S: 0, 64>
<S: 0, 64>
<Off/Diffserv>
<0..63>
<0..63>
Contact us
Contact us
58