Danfoss VLT AutomationDrive FC 300 Instruction Manual page 100

Index
Pre-start.................................................................................................. 3-1
Programming
Programming... 1-2, 2-10, 3-6, 4-2, 5-3, 5-4, 5-9, 8-2, 3-3, 4-1,
Example............................................................................................. 5-1
Pulse/Encoder Inputs.................................................................... 10-14
Q
Quick
Menu.................................................................................. 5-1, 5-3, 4-2
Set-up................................................................................................. 3-4
R
Ramp-down Time............................................................................... 3-6
Ramp-up Time...................................................................................... 3-6
RCD........................................................................................................... 2-6
Reference...................................................................... 0-1, 7-2, 7-3, 4-2
Relay Outputs.......................................................................... 2-8, 10-15
Remote
Commands........................................................................................ 1-3
Programming................................................................................... 5-9
Reference........................................................................................... 7-2
Reset...................................................... 4-1, 4-4, 7-3, 8-1, 8-2, 8-8, 4-3
RFI Filter.................................................................................................. 2-7
RMS Current.......................................................................................... 1-3
Run
Command......................................................................................... 3-6
Permissive......................................................................................... 7-2
S
Safety Inspection................................................................................. 3-1
Serial Communication...... 1-3, 2-8, 2-9, 4-3, 7-1, 7-2, 7-3, 8-1, 2-
Setpoint.................................................................................................. 7-3
Setup....................................................................................................... 4-2
Set-up.............................................................................................. 3-6, 4-2
Shielded
Cable.................................................................................. 2-1, 2-5, 3-2
Control Cables................................................................................. 2-9
Wire..................................................................................................... 2-5
Short Circuit.......................................................................................... 8-4
Smart Application Set-up (SAS)..................................................... 3-3
Specifications.................................................................. 1-2, 2-15, 10-1
Speed Reference...................................................... 2-11, 3-6, 5-2, 7-1
Start Up................................................................................................... 5-1
Start-up.................................................................................. 1-2, 4-4, 3-1
Status
Messages........................................................................................... 7-1
Mode................................................................................................... 7-1
VLT ® AutomationDrive Instruction
Manual
4-3, 5-1
14, 10-15
®
MG33AL22 - VLT is a registered Danfoss trademark
Stop Command.................................................................................... 7-2
Supply Voltage........................................................... 2-7, 2-8, 3-1, 8-5
Surroundings................................................................................... 10-16
Switching Frequency......................................................................... 7-2
Symbols.................................................................................................. 0-1
System
Feedback........................................................................................... 1-3
Monitoring........................................................................................ 8-1
Start-up.............................................................................................. 3-6
T
Technical Data................................................................................. 10-12
Temperature Limits............................................................................ 3-2
Terminal
53...................................................................................... 5-1, 2-11, 5-1
54....................................................................................................... 2-11
Programming................................................................................ 2-10
Programming Examples............................................................... 5-2
Thermistor
Thermistor........................................................................ 2-7, 8-3, 6-4
Control Wiring................................................................................. 2-7
Tightening Of Terminals.............................................................. 10-25
Torque
Characteristics............................................................................ 10-12
Limit..................................................................................................... 3-6
Transient Protection.......................................................................... 1-3
Trip
Trip....................................................................................................... 8-1
Function............................................................................................. 2-5
Lock..................................................................................................... 8-1
Troubleshooting......................................................................... 1-2, 9-1
U
Uploading Data To The LCP............................................................ 4-4
V
Voltage
Imbalance.......................................................................................... 8-2
Level............................................................................................... 10-12
W
Warning
And Alarm Definitions.................................................................. 8-2
And Alarm Displays........................................................................ 8-1
And Alarm Types............................................................................. 8-1
Wire Sizes....................................................................................... 2-5, 2-6
12-3