Siemens SIMATIC ET 200pro Quick Manual page 13

Illustrations
Figure 1-1: ET 200pro with motor starters . . . . . . . . . . . . . . . . . . . . .
Figure 1-2: ET 200pro with motor starters and electronic modules . . . . . . . .
Figure 1-3: ET 200pro with motor starters up to category 4 . . . . . . . . . . . .
Figure 2-1: Components and configuration for the example . . . . . . . . . . . .
Figure 2-2: Set PROFIBUS address 6
Figure 2-3: Circuit for the example . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-4: Assemblies in 'HW Config' . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-5: View in the status window 'DP slave diagnosis' . . . . . . . . . . . .
Figure 3-1: Installation position . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-2: Diagrams for derating
Figure 6-1: Rear wall bus module
Figure 7-1: View of maintenance isolating module . . . . . . . . . . . . . . . . .
Figure 7-2: Circuit diagram of maintenance isolating module . . . . . . . . . . .
Figure 7-3: Assignment of the main power connections
at the maintenance isolating module . . . . . . . . . . . . . . . . . .
Figure 7-4: View of safety local maintenance isolating module . . . . . . . . . .
Figure 7-5: Circuit diagram for safety local maintenance isolating module . . . . .
Figure 7-6: Assignment of the main power connections
at the safety local maintenance isolating module . . . . . . . . . . .
Figure 7-7: Assignment of the auxiliary current circuits
at the safety local maintenance isolating module . . . . . . . . . . .
Figure 7-8: Configuration of the safety local maintenance isolating module . . . .
Figure 7-9: View of disconnecting module 400 V
Figure 7-10: Circuit diagram for disconnecting module 400 V . . . . . . . . . . . .
Figure 7-11: Assignment of the connectors on the disconnecting module 400 V . .
Figure 7-12: Current flow in the power bus . . . . . . . . . . . . . . . . . . . . .
Figure 8-1: View of DSe and RSe motor starters, standard and high feature . . .
Figure 8-2: View of electronic starters sDSSte / sDSte and sRSSte / sRSte . . . .
Figure 8-3: Assignment of the main power connections at the motor starter . . .
Figure 8-4: Assignment of M12 plug connector at the motor starter . . . . . . .
Figure 8-5: Circuit diagram - DSe direct starter, standard and high feature . . . .
Figure 8-6: Circuit diagram - RSe reversing starter, standard and high feature . .
Figure 8-7: Electrical service life of contactor . . . . . . . . . . . . . . . . . . .
Figure 8-8: Typical current and torque characteristics of a 3-phase induction motor
Figure 8-9: Current and torque characteristics with star-delta start . . . . . . . .
Figure 8-10: Phase control of the mains voltage by means of
semiconductor elements on the soft starter sDSSte / sRSSte . . . . .
Figure 8-11: Current and torque characteristics when a soft starter is used . . . .
Figure 8-12: Time ramp / time diagram, sDSSte / sDSte, sRSSte / sRSte . . . . . .
Figure 8-13: Duty cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xi
. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
SIMATIC - ET 200pro motor starter
GWA 4NEB 950 5661-02 DS 04
1-6
1-6
1-7
2-3
2-4
2-5
2-7
2-12
3-2
3-5
6-1
7-2
7-3
7-3
7-6
7-7
7-7
7-8
7-8
7-11
7-11
7-12
7-13
8-4
8-5
8-6
8-7
8-8
8-9
8-16
8-17
8-18
8-19
8-20
8-23
8-24