Pause Time Setting; Transaction Report Print Select Setting; Speaker Volume Settings; Activity Report Print Select Setting - Sharp MX-M350N Facsimile Operation Manual

KEY OPERATOR PROGRAMS

Pause time setting

This setting is used to select the duration of pauses
that are inserted in destination fax numbers.
Normally the setting is 2 seconds, which means
that each time the [PAUSE] key is touched when
dialing or storing a fax number, a pause of 2
seconds is inserted.
The pause time can be set to any number of
seconds from 1 to 15.

Speaker volume settings

This program is used to adjust the volume of the
five following sounds that are emitted from the
speaker: 1.speaker, 2. ringer volume, 3. line
monitor, 4. fax
communication error signal.
KEY OPERATOR PROGRAMS
SPEAKER VOLUME SETTINGS
SPEAKER
RINGER VOLUME
LINE MONITOR
Volume:Low Volume:Medium
To change the volume, touch the desired volume
key. Factory default
destinations.

Original print on transaction report

This program is used to have part of the first page
of the fax printed on the transaction report . This
program is used in conjunction with the transaction
report print select setting (at right), and is not
effective when printing of the transaction report is
disabled.
This program is normally configured so that part of
the fax is printed on the transaction report when a
transmission is not successful.
Remote reception number setting
(only when extension phone is connected)
When a call is received (not made) on an extension
phone connected to the machine, fax reception can
be activated by entering a one-digit number and
pressing " " twice on the phone's keypad. This
number is called the remote reception number, and
you can set it to any number from "0" to "9". The
number is normally set to "5".
8-6
receive signal, 5. Fax
OK
1/2
Volume:High Off
setting varies with

Transaction report print select setting

This program is used to select the condition for
printing a transaction report. The condition is set
separately for normal transmission, broadcast
transmission, reception, and confidential reception.
SINGLE SENDING
PRINT OUT ALL REPORT
PRINT OUT ERROR REPORT ONLY
NO PRINTED REPORT
Touch the key to display the next two settings. Select the
print conditions for receptions and confidential receptions
RECEIVING
PRINT OUT ALL REPORT
PRINT OUT ERROR REPORT ONLY
NO PRINTED REPORT
The normal settings are indicated by shading

Activity report print select setting

This program is used to have the activity report stored in
the machine's memory printed out at regular intervals.
You can choose to have the report automatically printed each
time the number of stored transactions exceeds 99*, or have the
report printed at a specified time every day (only once per day).
The report is normally set to not print out. Select "AUTO
PRINT AT MEMORY FULL" to have the report automatically
printed when the number of stored transactions (the
combined total of transmissions and receptions) exceeds 99*.
To have the report automatically printed at a
specified time, check the "PRINT DAILY AT
DESIGNATED TIME" box and then select the time
with the "HOUR" and "MINUTE" keys that appear.
KEY OPERATOR PROGRAMS
ACTIVITY REPORT PRINT SELECT SETTING
AUTO PRINT AT MEMORY FULL
PRINT DAILY AT DESIGNATED TIME
Touch the "HOUR" and "MINUTE" keys and then set the
hour by touching the
the same way. When finished, touch the [OK] key.
NOTES
● If you only select the "PRINT DAILY AT DESIGNATED
TIME" setting and the number of recorded transactions
exceeds 99* before the specified time, each new
transaction will delete the oldest transaction (the oldest
transaction will not be printed).
● The activity report can also be printed out on demand
(see "PRINTING OUT SETTINGS" on page 8-11).
*AR-M351N/AR-M451N only. On the AR-M351U/
AR-M451U, 50 transactions are retained.
BROADCASTING
PRINT OUT ALL REPORT
PRINT OUT ERROR REPORT ONLY
NO PRINTED REPORT
CONFIDENTIAL RECEPTION
PRINT OUT NOTICE PAGE
NOT PRINT OUT NOTICE PAGE
above.
OK
HOUR MINUTE
13 01
and keys. Set the minute in