Checking The Size Of A Loaded Original; Manually Setting The Scanning Size - Sharp MX-M350N Facsimile Operation Manual

Facsimile expansion kit
Hide thumbs Also See for MX-M350N:
Table of Contents

Advertisement

CHECKING THE SIZE OF A LOADED ORIGINAL

When a standard-size* original is placed, the original size is automatically detected
(automatic original detection function) and displayed in the top half of the [ORIGINAL]
key. Check the key to make sure that the original size has been correctly detected.
:[AUTO] appears when the automatic original detection function is operating.
:Displays the original size.
If a non-standard size original is placed or if you wish to change the scanning size,
follow the steps below to manually set the original scanning size.
NOTE
* Standard sizes that can be detected are as follows:
A5, B5, B5R, A4, A4R, B4, A3, 5-1/2"x8-1/2", 8-1/2"x11", 8-1/2"x11"R, 8-1/2"x14", 11"x17". If a non-standard
size original is loaded (including special sizes), the closest standard size may be displayed, or the original size
may not appear at all.

MANUALLY SETTING THE SCANNING SIZE

If you load an original that is not a standard size (such as an INCH size), or if the size is not detected correctly, you
must touch the [ORIGINAL] key and set the original size manually. Perform the following steps after loading the
document in the automatic document feeder or on the document glass.
Touch the [ORIGINAL] key.
1
STANDARD
RESOLUTION
AUTO
A4
ORIGINAL
2
Touch the key under [SCAN SIZE].
SPEAKER
SCAN SIZE
SEND SIZE
100%
AUTO
A4
AUTO
2-SIDED
2-SIDED
BOOKLET
TABLET
Touch the desired original size key.
3
SPEAKER
RESEND
OK
1 /
8 X11
2
A5
A5
A4
AB
AUTO
A5R
A4R
INCH
MANUAL
B5
B4
B5R
A3
LONG SIZE
STOM
ZE
STANDARD SIZE
SIZE INPUT
If you wish to select an INCH size, touch
the [AB/INCH] key and then touch the
desired original size key.
SPEAKER
RESEND
OK
5 X8
1 /
8 X13
1 /
1 /
2
2
2
AB
5 X8 R
1 /
1 /
8 X14
1 /
2
2
2
INCH
8 X11
11X17
1 /
2
8 X11R
1 /
LONG SIZE
2
STANDARD SIZE
SIZE INPUT
1-8
If the address book screen
appears,
touch
the
[CONDITION SETTINGS]
key
to
display
the
condition settings screen
(page 1-5).
[AUTO]
is
no
longer
highlighted.
[MANUAL]
and the original size key
you
touched
are
highlighted.
If you placed a long original,
touch the
key.
LONG SIZE
[INCH]
is
highlighted
and INCH size keys are
displayed. To return to
the inch palette, touch
the [AB/INCH] key once
again.
If you placed a non-standard size original
on the document holder or on the
document glass, touch the [SIZE INPUT]
tab and then enter the width (X) and length
(Y) of the original with the
X
OK
A
Y
(64 432)
420
X
mm
(64 297)
297
Y
mm
STANDARD SIZE
SIZE INPUT
mm (2-1/2 to 11-5/8 inch) can be entered in Y.
If you frequently send documents that are the same
non-standard size, you can store the dimensions as explained
in "STORING, DELETING, AND USING ORIGINAL SIZES"
on the following page. This will allow you to omit entry of X and
Y each time you send that size of document.
4
Touch the outer [OK] key.
Touch the [OK] key to return to the screen of step 2.
5
Touch the outer [OK] key.
SPEAKER
RESEND
OK
SEND SIZE
AUTO
-SIDED
The selected size appears in the top half of
6
the [ORIGINAL] key.
STANDARD
RESOLUTION
A4
1 /
8 X11
2
ORIGINAL
STANDARD
RESOLUTION
AUTO A4
ORIGINAL
keys.
X
(width)
is
initially
selected. Enter X and
then touch the Y (
)
key to enter Y. A width of
64 to 432 mm (2-1/2 to 17
inch) can be entered in X,
and a length of 64 to 297

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Mx-m450nMx-m350uMx-m450uAr-fx12

Table of Contents