Table of Contents
Summary of Contents for FibberservCL FSSEG-X3
- Page 1 (3) User Guide for Installation of Smart Home Devices Home Automation All-in-One Hassle Free Installation Multiple Control Devices Property of FIBERSERV CARIBBEAN LIMITED 868-731-8097 Info@fiberservcl.com www.fiberservcl,com...
- Page 2 FSSEG-X3 Smart Gateway Quick Start Guide 1. Introduction The FSSEG-X3 Smart Gateway acts as a central platform for your smart home system. It allows you to add up to 50 Smart Devices into the system. It connects to the Internet, to be controlled by the mobile app.
-
Page 3: Led Status
(means the gateway is in AP mode) Tip: If the LED indicator is not flashing purple, please reset the FSSEG-X3 gateway to default factory settings by pressing and holding down the reset button with pin key tool for ten seconds. - Page 4 Q7. How can I use this system in the place that has no Wi-Fi router? A7: You can only use the system locally on Android device by following the steps below; Step 1: Connect your smartphone to the Wi-Fi hotspot of the FSSEG-X3 Smart Gateway which starts with “ZB” and ends in six digits.
- Page 5 Green LED flashes three times Joining a network or return to factory settings. Red LED flashes once Alarm is triggered 3. Get started 3.1. To get started, you will need: FSSEG-X3 Smart Gateway • FSDWS312 Door/Window Sensor • The Fiberserv mobile app •...
- Page 6 3.2 Connect to Gateway’s network 1: Power on the Door/Window Sensor. Press the reset button and the LED indicator will flash red three times indicating the sensor is ready to join the gateway's network 2: Select “Add new devices” in the app menu. Tip: You can also press the “Z”...
-
Page 7: Mounting Instructions
3.3 Mounting instructions 1. Make sure that the surface is clean to ensure good bonding. 2. Peel off the liner on the double-sided tape and place the sensor on the door/window. Be sure that the two sensor parts should be within 1/8” of each other when the door/window is closed. Please refer to the mounting example below. - Page 8 TRUE SENSE OF SECURITY FSPIR303 ZigBee Motion Sensor Quick Start Guide 1. Introduction The FSPIR303 ZigBee motion sensor detects movement in your property. It allows you to receive notifications from the mobile app when movement is detected. This can be used to trigger an alarm or a light etc.
- Page 9 The device has detected movement. 2.4. Sensing range (Above view) 2.5. Sensing range (Side view) 3. Get started 3.1. To get started, you will need: • FSSEG-X3 Smart Gateway FSPIR303 Motion Sensor • The Fiberserv mobile app • Then follow the steps below: Step 1: Remove the pull tab to power on the device.
- Page 10 Tip: You can also press the “Z” button of the gateway for two seconds until the LED indicator turns solid blue. Step 3: Use a pin key tool to press and hold the reset button for two seconds until the LED flashes green to add it to the system.
- Page 11 Option 2: Follow the diagrams below to fix the bracket and put the detector onto the bracket. Your motion sensor is now ready for use. 4. FAQ Q1. How can I return the device to factory default settings? A1: Use a pin key tool to press and hold the reset button for five seconds until the LED flashes six times.
- Page 12 TRUE SENSE OF SECURITY FSIPC804 Fixed IP Camera Quick Start Guide 1. Introduction The IP Camera allows you to monitor your home anywhere using your mobile phone. It is designed with a high definition processing chip that gives high quality, fast loading images day and night.
- Page 13 2. Get started 21. To get started, you will need: FSSEG-X3 Smart Gateway • FSIPC804 IP Camera • The Fiberserv mobile app • 2.2 Set up your IP camera 1. Connect your IP camera to the USB power adaptor and apply power.
- Page 14 • Adjust its temperature • Set an on/off schedule • 2. Get started 2.1 To get started, you will need: FSSEG-X3 Smart Gateway • FSLED622 CCT Tunable LED Bulb • The Fiberserv mobile app • Then follow the steps below: Step 1: Turn OFF the light switch Step 2: Fit the LED622 LED Bulb into the light or lamp socket.
- Page 15 Step 5: Select “Add new devices” in the menu of the app. Step 6: Turn ON the switch, the LED622 LED Bulb will flash twice. Step 7: The LED622 will try to pair with the gateway. The LED622 LED Bulb will flash once more when pairing is successful. Please go to the app to check if it is paired successfully.
- Page 16 COST SAVINGS & ENERGY EFFICIENCY FSSLC603 Remote Control Quick Start Guide 1. Introduction The FSSLC603 ZigBee Dimmer Switch is designed to control the following features of a CCT Tunable LED bulb: • Turn on/off the LED bulb • Adjust the brightness of the LED bulb •...
- Page 17 2.2. Buttons Introduction Rotary button • Turn ON and OFF the LED bulb. • Adjust the brightness of the LED bulb. • Adjust the colour and temperature of the LED bulb. Reset button • Return the device to default factory settings. •...
- Page 18 Step 4: Use a pin key tool to press the reset button. Then the Dimmer Switch will try to join the gateway based system. Step 5: Check if the Dimmer Switch is added into the gateway. When the Dimmer Switch is added into the gateway based system successfully, the LED indicator will be flashing green three times.
- Page 19 COST SAVINGS & ENERGY EFFICIENCY FSWSP404 Smart Plug US Quick Start Guide 1. Introduction The Smart plug FSWSP404 allows you to switch your devices on and off and allows you to measure power and record total used power in kilowatt hours (kWh) wirelessly via your mobile App. •...
-
Page 20: Safety Notice
Get started 3.1 To get started, you will need: A SEG-X3 Gateway • • FSWSP404 Smart Plug The Fiberserv mobile app. • 3.2 Connect to the gateway’s network 1. Set your gateway to permit joining. (Add new device). 2. Plug in the smart plug and the LED indicator will start flashing (reset it if not). 3. -
Page 21: Fcc Statement
FCC Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. - Page 22 COST SAVINGS & ENERGY EFFICIENCY FSRC204 Remote Control Quick Start Guide 1. Introduction The FSRC204 ZigBee Remote Control is used to control up to four devices either at one time or individually. For e.g to control CCT Tunable LED bulbs ,the Remote Control can be used to: •...
- Page 23 _________________________________________________________________________ 2.2. Buttons and Switch All ON and all OFF button • Turn on and off all the paired devices such as LED bulbs, smart plugs and power relays.
- Page 24 Four individual ON/OFF buttons • Turn ON/OFF the corresponding device individually. Status button The corresponding individual ON/OFF buttons will illuminate according to its status. • Reset button • Set the device to join the ZigBee network. Return the device to factory settings. •...
- Page 26 3. Get started To get started, you will need: A SEG-X3 Smart Gateway • • 1 to 4 of CCT Tunable LED bulb LED622 (You will need at least one LED bulb) The mobile app • Then follow the steps below: Step 1: Check the FSRC204 status.
- Page 27 Tip: for this step, you could also press the “Z” button of the gateway for two seconds until the LED indicator turns solid blue. Step 3: Use a pin key tool to press the RC204 reset button. Then the device will join the ZigBee network of the gateway.
- Page 28 (4) After successful pairing, the LED bulb will stop flashing, and the corresponding status LED indicator will flash green three times. Tip: If pairing fails, the corresponding status LED indicator will flash red three times. If this happens you must repeat this process again.
- Page 29 Battery pull tab Power on Water Leak Sensor. Pull out the battery pull tab to power on the sensor. 3. Get started 3.1. To get started, you will need: FSSEG-X3 Smart Gateway • FSWLS306 Water Leak Sensor • The Fiberserv mobile app •...
-
Page 30: Mounting Instructions
1. Set your gateway to permit pairing. (Add new device). 2. Power on the Water Leak Sensor. Use a pin to press the reset button in the Water Leak Sensor for two seconds until the LED rapidly flashes yellow. The sensor will join the gateway’s network. The LED light will turn solid for a while when it has successfully added. - Page 31 LIFE SAVING/AVOID MAJOR DISRUPTIONS FSSD324 Smoke Detector Quick Start Guide 1. Introduction The FSSD324 ZigBee smoke detector is integrated with an ultra-low-power ZigBee wireless module. It is a warning device that allows you to detect the presence of smoke in real time. 2.
-
Page 32: Reset Button
Green LED flashes six times The device leaves the network 3. Get started 3.1. To get started, you will need: • FSSEG-X3 Smart Gateway • FSSD324 Smoke Detector • The Fiberserv mobile app Then follow the steps below: Step 1: Remove the pull tab to power on the device. - Page 33 Tip: for this step, you could also press the “Z” button of the gateway for two seconds until the LED indicator turn solid blue. Step 3: Use a pin key tool to press and hold the reset button for two seconds until the LED flashes green to add it to the system.
- Page 34 If using screws, attach the bracket to the respective surfaces using the screws provided. Then rotate the smoke detector main body onto the bracket: 4. FAQ Q1. How can I return the device to factory default settings? A1: Use a pin key tool to press and hold the reset button for five seconds until the LED flashes six times.
- Page 35 LIFE SAVING/AVOID MAJOR DISRUPTIONS FSGD334 Gas Detector Quick Start Guide 1. Introduction The Gas Detector uses an extra low power consumption ZigBee wireless module. It is used for detecting combustible gas leakage. Also it can be used as a ZigBee repeater that extends wireless transmission distance. The gas detector adopts high stability semi-conductor gas sensor with little sensitivity drift.
- Page 36 3. Get started 3.1. To get started, you will need: • FSSEG-X3 Smart Gateway • FSGD334 Gas Detector • The Fiberserv mobile app 3.2 Connect to gateway’s network 1. Plug the gas detector to power outlet, the LED indicator will flash alternatively for three minutes, indicating the sensor is warming up.
- Page 37 Refer to FCL TRAINING MANUAL - PRODUCT SPECS for Technical specifications.
- Page 38 LIFE SAVING/AVOID MAJOR DISRUPTIONS FSCMD344 Carbon Monoxide Detector Quick Start Guide 1. Introduction The CO Detector uses an extra low power consumption ZigBee wireless module that is specially used for detecting carbon monoxide. The sensor adopts high performance electrochemical sensor that has a high stability, and little sensitivity drift.
-
Page 39: Mounting Steps
The LED indicator will flash alternatively and the alarm sound will beep four times at the same time 3. Get started 3.1. To get started, you will need: • FSSEG-X3 Smart Gateway • FSCMD344 CO Detector • The Fiberserv mobile app 3.2 Connect to gateway’s network... - Page 40 2. Peel off the liner of the double-sided tape on the bracket and place the bracket to where you want to place it. 3. Screw the CO detector into the bracket Refer to FCL TRAINING MANUAL - PRODUCT SPECS for Technical specifications.
- Page 41 • Reset. Press and hold the reset button for five seconds until the LED indicator flashes green six times to reset the smart siren to default factory setting. 3. Get started 3.1. To get started, you will need: • FSSEG-X3 Smart Gateway • FSSIR216 Smart Siren • The Fiberserv mobile app 3.2 Connect to gateway’s network...
- Page 42 2. Set your gateway to permit joining. (Add new device). 3. The siren will then join the gateway's network automatically. The LED indicator on the siren will light up green when it has successfully joined. 4. Now you will be able to see the siren under "Security" in the mobile App. 3.3 Mounting instructions Please install the siren on a flat surface in a highly visible position for maximum deterrence against potential intruders.
- Page 43 Refer to FCL TRAINING MANUAL - PRODUCT SPECS for Technical specifications.
- Page 44 COMFORT & CONVENIENCE FSAC201 Split Air Condition Control(IR Blaster) Quick Start Guide 1. Introduction The FSAC201 ZigBee split AC (Air Conditioner) Control converts control commands sent using a ZigBee signal into IR (Infra-Red) signal to control your AC system. It allows you to control the system mode, temperature, fan speed, ventilation and swing of the air conditioner remotely from the mobile app on your mobile phone.
- Page 45 2.2. Buttons Introduction “Z” button • Search pairing code • Save the chosen paring code • Stop searching for a pairing code • Continue to search for a pairing code Previous button • Switch to the “previous” option • Enter the Brand code selection mode Next button •...
- Page 46 2.4. LED Indicator The LED indicator status is as below: 3. Get started To get started, you will need: • FSSEG-X3 Smart Gateway • FSAC201 Split AC Control • The Fiberserv mobile app Then follow the steps below: Step 1: Insert the AC201 Split AC Control into a power socket facing your air conditioner that you would like to connect to.
- Page 47 Tip: for this step, you could also press the “Z” button of the gateway for two seconds until the LED indicator turn solid blue. Step 3: The AC201 Split AC Control will add into the gateway; the LED indicator will turn orange when pairing is successful.
- Page 48 Refer to FCL TRAINING MANUAL - PRODUCT SPECS for Technical specifications.
-
Page 49: Comfort & Convenience
COMFORT & CONVENIENCE FSPCT503-Z Multi-Stage Smart Thermostat Quick Start Guide 1. Introduction The PCT503-Z ZigBee Thermostat is designed to work with the ZigBee gateway so that you could control your Thermostat remotely. It can control: • Cooling: one and two stages (Y1, Y2) •... - Page 50 2.2. Buttons Introduction Rotary button • Choose options • Confirm options • Adjust temperature Home button • Switch between home screen and date & time screen Away button • Switch between home screen and away screen Hold button • Enter “Permanent hold” Tip: operational details will be described below.
-
Page 51: Activity Sensor
Activity sensor is used to detect the activity so that the display could be on/off automatically. 2.5. Display 3. Get started To get started, you will need: • FSSEG-X3 Smart Gateway • FSPCT503-Z Thermostat • The Fiberserv mobile app Then follow the steps below: ... - Page 52 Step 2: Set to suit your HVAC. After installing, press the rotary button, and then follow the setup guide. Step 3: Select “Add new devices” in the menu of the app Tip: for this step, you could also press the “Z” button of the gateway for two seconds until the LED indicator turn solid blue.
- Page 53 Refer to FCL TRAINING MANUAL - PRODUCT SPECS for Technical specifications.
-
Page 55: Thermostat Installation
6. Installation Guide 6.1. In the box 6.2. Thermostat Installation Step 1: Turn power off This protects yourself and your equipment. Turn off the power at the breaker box or switch that controls your heating/cooling system. Please check that your system is off. Step 2: Remove the old thermostat’s cover Some covers pop off, while others need to be unscrewed Step 3: Check your system... - Page 56 If your old thermostat is labelled 120V or 240V or has thick wires with wire nuts, your system is high voltage. If you are not sure, please contact support. Step 4: label wires with Tags Step 5: Install the wiring module (Optional) Note: Check your wires, see if there's C-wire.
- Page 57 2. Disconnect the R/RC, W-O/B, Y, G wires form the control board and reconnect them correspondingly to the 4 terminals side of the wiring module. For Y-wire and G-wire, you can connect the Y-wire to S-terminal, G-wire to C terminal, then change the label of the Y-wire to the S-wire, the G-wire to the C-wire.
- Page 58 Step 6: Remove the old thermostat base Unscrew the old thermostat base from the wall, gently pull it out and ensure wires do not fall back into the hole in the wall. Step 7: Attach the base of the FSPCT503 Thermostat to the wall Bundle and insert wires through the hole in the base of the FSPCT503 Thermostat, then attach the base to the wall with the screws.
-
Page 59: Wiring Diagrams
6.3. Wiring Diagrams Below you will find the wiring diagrams for the common HVAC equipment. Remove the jumper for RC or RH, switch the DIP switch in the back of the thermostat to RC if you have connected both RC-wire and RH-wire to the wall plate, otherwise switch it to the RC&RH side. - Page 60 Remove the jumper for RC or RH, switch the DIP switch in the back of the thermostat to RC if you have connected both RC-wire and RH-wire to the wall plate, otherwise switch it to the RC&RH side. Remove the jumper for RC or RH, switch the DIP switch in the back of the thermostat to RC if you have connected both RC-wire and RH-wire to the wall plate, otherwise switch it to the RC&RH side.