Dahua Network Camera Web 3.0 Operation Manual
  1. Manuals
  2. Brands
  3. Dahua Manuals
  4. Security Camera
  5. Network Camera Web 3.0
  6. Operation manual

Dahua Network Camera Web 3.0 Operation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Dahua Network Camera Web 3.0 Operation Manual
Dahua Network Camera Web3.0 Operation Manual
Version 2.0.0
Zhejiang Dahua Vision Technology CO., LTD
i

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Network Camera Web 3.0 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Dahua Network Camera Web 3.0

Summary of Contents for Dahua Network Camera Web 3.0

  • Page 1 Dahua Network Camera Web 3.0 Operation Manual Dahua Network Camera Web3.0 Operation Manual Version 2.0.0 Zhejiang Dahua Vision Technology CO., LTD...

  • Page 2: Table Of Contents

    Dahua Network Camera Web 3.0 Operation Manual Table of Contents Product Overview ........................1 Initial Config ..........................2 Device Initialization ....................... 2 Login and Logout ......................4 2.2.1 Log in WEB Interface ....................4 2.2.2 Logout ........................6 Reset Password ......................6 Live ..............................
  • Page 3 Dahua Network Camera Web 3.0 Operation Manual 5.2.3 PPPoE ........................56 5.2.4 DDNS ........................57 5.2.5 IP filter ........................59 5.2.6 SMTP （e-mail) ..................... 59 5.2.7 UPnP ........................61 5.2.8 SNMP ........................62 5.2.9 Bonjour ........................64 5.2.10 Multicast ......................... 65 5.2.11 802.1x ........................
  • Page 4 Dahua Network Camera Web 3.0 Operation Manual Important The following functions are for reference only. Some series products may not support all the functions listed below. Cybersecurity Recommendations 1. Change Passwords and Use Strong Passwords The number one reason systems get “hacked” is due to having weak or default passwords. It is recommended to change default passwords immediately and choose a strong password whenever possible.
  • Page 5 Dahua Network Camera Web 3.0 Operation Manual On older IP Camera firmware, the ONVIF password does not change when you change the system’s credentials. You will need to either update the camera’s firmware to the latest revision or manually change the ONVIF password.
  • Page 6 Dahua Network Camera Web 3.0 Operation Manual 12. Multicast: Multicast is used to share video streams between two recorders. Currently there are no known issues involving Multicast, but if you are not using this feature, deactivation can enhance your network security.
  • Page 7 Dahua Network Camera Web 3.0 Operation Manual  Do not aim the device at strong light to focus, such as lamp light and sun light, otherwise it might cause over brightness or light marks, which are not the device malfunction, and affect the longevity of Charge Coupled Device (CCD) or Complementary Metal-Oxide Semiconductor (CMOS).
  • Page 8 Dahua Network Camera Web 3.0 Operation Manual respective owners.  Please visit our website, contact the supplier or customer service if there is any problem occurred when using the device.  If there is any uncertainty or controversy, please refer to our final explanation.

  • Page 9: Product Overview

    Dahua Network Camera Web 3.0 Operation Manual 1 Product Overview The common networking mode for IPC is to connect IPC to PC via switch or router. The common network mode is shown in Figure 1-1. Figure 1-1 Before you have access to network camera via the Internet, you need to acquire its IP address. Users...

  • Page 10: Initial Config

    Dahua Network Camera Web 3.0 Operation Manual 2 Initial Config In this chapter it is to introduce the device initial config operation, which includes device initialization, login device, log out WEB interface and password reset. 2.1 Device Initialization It needs to implement device initialization when you use the device for the first time. Here it is to take WEB operation as an example to introduce device initialization.
  • Page 11 Dahua Network Camera Web 3.0 Operation Manual Parameter Note User name The default user name is admin Password The password ranges from 8 to 32 digitals. It can contain letters, numbers and special characters (excluding “'”,“"”,“;”,“:”,“&”) . The password shall Confirm contain at least two categories.

  • Page 12: Login And Logout

    Dahua Network Camera Web 3.0 Operation Manual Figure 2-3 Step 5 Click Save and device initialization is completed. 2.2 Login and Logout Here it is to introduce device login and WEB interface logout via browser, it is to take IE Explorer 8 as an example to make introduction.
  • Page 13 Dahua Network Camera Web 3.0 Operation Manual Figure 2-4 Step 2 Input the password of admin user. Step 3 Click Login. It will display the Live interface after it logged in successfully, which is shown in Figure 2-5. Note Different devices have different functions with different interface display; please refer to the actual...

  • Page 14: Logout

    Dahua Network Camera Web 3.0 Operation Manual Figure 2-5 2.2.2 Logout Click Logout and return to WEB login interface. After logging in the device WEB, the system will hibernate automatically if it fails to operate the device for a period of time. It can recover to normal working status quickly after entering password.
  • Page 15 Dahua Network Camera Web 3.0 Operation Manual Figure 2-6 Step 2 Click Forgot password? The system will display the interface of Reset Password, which is shown in Figure 2-7. Figure 2-7 Step 3 Reset login password. Scan the QR code according to the interface prompt and acquire security code, then input the security code which is received via your reserved email.
  • Page 16 Dahua Network Camera Web 3.0 Operation Manual  Please use the security code to reset the password within 24 hours after you received the security code via your reserved email. Otherwise the security code will be invalid.  If you fail to use security code for twice continuously, then the system will prompt that it fails to acquire security code for the third time.

  • Page 17: Live

    Dahua Network Camera Web 3.0 Operation Manual 3 Live 3.1 Preview Interface Introduction After you logged in, you can see the live monitor window. See Figure 3-1. Figure 3-1 The preview interface of WEB client includes four function columns; please refer to Table 3-1 for more details.

  • Page 18: Video Window Function Option

    Dahua Network Camera Web 3.0 Operation Manual Function Note It includes following four items: Main stream: stream value is much bigger, image definition is higher, but it takes bigger bandwidth, which is applied to storage and surveillance. Sub stream 1: stream value is comparatively smaller than main...
  • Page 19 Dahua Network Camera Web 3.0 Operation Manual  When the video is in the original status, click it you can Digital select any zone to zoom in. In the non-original status, Zoom you can drag the zoom-in zone in specified range. Right click mouse to restore previous status.

  • Page 20: Video Window Setup

    Dahua Network Camera Web 3.0 Operation Manual 3.3 Video Window Setup The interface is shown as in Figure 3-3. Figure 3-3 3.3.1 Image Adjustment See Figure 3-4 for image adjustment. Figure 3-4 Click this button to display/hide image control interface. Click it to open picture setup interface. This interface is on the top right pane.

  • Page 21: Window Display Mode

    Dahua Network Camera Web 3.0 Operation Manual Restore brightness, contrastness saturation and hue to system default setup. Table 3-3 3.3.2 Window Display Mode It is to adjust the display mode of video window; display mode includes suitable size and original size, full screen, original ratio and suitable window, please refer to Table 3-4 for more details.
  • Page 22 Dahua Network Camera Web 3.0 Operation Manual Figure 3-5 Please refer to Table 3-5 for more details about the parameters of zoom and focus. Parameter Function Adjust the focal length of the lens by clicking or long pressing “+”“-”buttons. Zoom The speed is used to adjust the length of one step during single click.

  • Page 23: Face Recognition/Comparison

    Dahua Network Camera Web 3.0 Operation Manual 3.3.6 Face Recognition/Comparison It is to enable face recognition/comparison function according to the actual environment setting, the precondition is to select “Setting > Event > Smart Plan”, enable the total switch of corresponding IVS, enable the “Face Recognition”...
  • Page 24 Dahua Network Camera Web 3.0 Operation Manual Figure 3-7...

  • Page 25: Playback

    Dahua Network Camera Web 3.0 Operation Manual 4 Playback Web client playback supports video playback and picture playback. Note Before playback, it needs to refer to 5.4 Storage for setting period, storage mode and record control. 4.1 Playback The playback interface is shown as in Figure 4-1.

  • Page 26: Function Of Play

    Dahua Network Camera Web 3.0 Operation Manual 4.1.1 Function of Play Figure 4-2 Figure 4-3 The function of play is shown as in Figure 4-2 Figure 4-3 Parameter Function When you see this button, it means pause or not played record. Click on this ①...

  • Page 27: Playback File

    Dahua Network Camera Web 3.0 Operation Manual 4.1.2 Playback File Figure 4-4 In calendar, blue date represents data currently has video record or snapshot. See Figure 4-4 Parameter Function Select “dav”, as video playback.  File Type Select “jpg” as picture playback.
  • Page 28 Dahua Network Camera Web 3.0 Operation Manual Figure 4-6 Parameter Function It means records within searched start time and end time on the date. Search Download There are two formats: dav, mp4. Format...

  • Page 29: Playback Cut

    Dahua Network Camera Web 3.0 Operation Manual Parameter Function  click the download button and download file to path in Ch. 5.1.2.5. Download  System does not support download and playback at the same time. Click on back button to go to calendar interface.

  • Page 30: Assistant Function

    Dahua Network Camera Web 3.0 Operation Manual Figure 4-9 Parameter Function Click on it, means video in past 24 hours. 24 hours Click on it, means video in past 2 hours. 2 hours Click on it, means video in past 1 hour.

  • Page 31: Play

    Dahua Network Camera Web 3.0 Operation Manual Figure 4-11 Figure 4-11 4.2.1 Play Figure 4-12 Default icon is and it means pause or not played picture. Click on play button to switch to normal play status. Icon become Click on it to pause.
  • Page 32 Dahua Network Camera Web 3.0 Operation Manual Figure 4-13 Step 1. Click on file list , select snapshot file of the date. Step 2. Double click on file in list, to play this snapshot. Parameter Function It means all snapshot files within the start time and end time of selected date.

  • Page 33: Snapshot Type

    Dahua Network Camera Web 3.0 Operation Manual Parameter Function Click the download button to open snapshot file or directly download to local Download according to the browser types. Click the back button to return to calendar interface and re-select time.
  • Page 34 Dahua Network Camera Web 3.0 Operation Manual After checking snapshot file type, in file list only display file of selected type. Users can also select the Figure 4-15 snapshot type to be displayed via the dropdown box above the file list. See...

  • Page 35: Setting

    Dahua Network Camera Web 3.0 Operation Manual 5 Setting Web client setup support camera, network, time, storage, system and system info view. 5.1 Camera The camera setting includes conditions, profile management, zoom and focus. 5.1.1 Conditions Note: The camera parameter may be different according to different models, please refer to the actual product for more details.
  • Page 36 Dahua Network Camera Web 3.0 Operation Manual Parameter Note Style It is to set the picture style, which includes standard, soft and vivid. It is to adjust the image overall brightness via linear adjustment mode. Brightness The larger the number is, the brighter the picture is, and on the contrary it is opposite.
  • Page 37 Dahua Network Camera Web 3.0 Operation Manual Click “Save” and complete the image parameter config of the camera. 5.1.1.2 Exposure Step 1 Select “Setup > Camera > Conditions > Exposure”. The system will display the “Exposure” interface Figure 5-2 which is shown in...
  • Page 38 Dahua Network Camera Web 3.0 Operation Manual Parameter Note It is the camera exposure mode. Note:  When “Anti-flicker” is “Outdor”, the “exposure mode” can be set as “gain priority” or “shutter priority” mode.  Different devices have different exposure modes; please refer to the actual interface.
  • Page 39 Dahua Network Camera Web 3.0 Operation Manual Parameter Note It is to process the image with multiframe (at least two frames), it 3D NR can realize noise reduction of the image by using the interframe information between the previous and latter frame.
  • Page 40 Dahua Network Camera Web 3.0 Operation Manual  When the “Mode” is set as “Scene Self-adaptation”, the system will auto adjust the image brightness according to the environmental brightness, which is to make the object display clearly in the scene.
  • Page 41 Dahua Network Camera Web 3.0 Operation Manual Figure 5-4 Step 2 Set WB mode.  When the “Mode” is set as “Auto”, the system can auto compensate white balance upon different color temperatures, which is to make the image color normal.
  • Page 42 Dahua Network Camera Web 3.0 Operation Manual Select “Setup > Camera > Conditions > Day & Night” and the system will display the interface of “Day & Night”, which is shown in Figure 5-5 Figure 5-5 Step 2 Set day & night parameter; please refer to the following sheet for more details.
  • Page 43 Dahua Network Camera Web 3.0 Operation Manual The image quality will become weak when the device is in the environment with fog or haze, you can enable defog function to adjust the image definition. Step 1 Select “Setup > Camera > Conditions > Defog” and the system will display the interface of “Defog”...
  • Page 44 Dahua Network Camera Web 3.0 Operation Manual Figure 5-7  When the “Profile Management” is set as “Full Time”, you can select “Always Enable” in “Day” or “Night’, the system will monitor according to the config of “always enable”. Figure 5-8 ...

  • Page 45: Video

    Dahua Network Camera Web 3.0 Operation Manual Click “Default” to restore the device to default config; click “Refresh” to check the latest config file of the device. 5.1.1.8 Zoom and Focus Note: Only motorized vari-focal devices support focus and zoom function.
  • Page 46 Dahua Network Camera Web 3.0 Operation Manual Step 1 Select “Setup > Camera > Video > Video” and the system will display the interface of “Video” which is Figure 5-11 Figure 5-12 shown in (Non fisheye) or (Fisheye). Figure 5-11...
  • Page 47 Dahua Network Camera Web 3.0 Operation Manual Parameter Function It will display the parameter when the device is fisheye. There are three installation modes for fisheye which are ceiling, wall mount and ground installation, please select installation mode according to the actual installation scene of the fisheye.
  • Page 48 Dahua Network Camera Web 3.0 Operation Manual Parameter Function Select “Enable” to enable sub stream. Sub Stream Enable The device supports enabling sub stream 1 and sub stream 2 at the same time. It can enhance image compression performance and Smart Codec reduce storage space by enabling intelligent encoding.
  • Page 49 Dahua Network Camera Web 3.0 Operation Manual Parameter Function Frame rate can be encoded by layer. It is a flexible encoding method. By default, it is 1 as 1 layer. You also can set 2/3/4 layers. I Frame Here you can set the P frame amount between two I frames.
  • Page 50 Dahua Network Camera Web 3.0 Operation Manual Figure 5-13 3. Select the needed resolution and clip the needed image on the interface, which is shown in Figure 5-15. 4. Click “Save”. You can check the clipped video in the preview interface (the sub stream 2 preview...
  • Page 51 Dahua Network Camera Web 3.0 Operation Manual Figure 5-14 Step 3 Click “Save” to complete video stream setup. 5.1.2.2 Snapshot Figure 5-15 The snapshot interface is shown as in Figure 5-15 Please refer to the following sheet for detailed information.
  • Page 52 Dahua Network Camera Web 3.0 Operation Manual Parameter Function There are two modes: general (schedule) and Event (activation). Snapshot type Image size It is the same as the resolution of main stream. It is to set the image quality. There are six levels.
  • Page 53 Dahua Network Camera Web 3.0 Operation Manual Figure 5-17 Figure 5-18...
  • Page 54 Dahua Network Camera Web 3.0 Operation Manual Figure 5-19 Figure 5-20...
  • Page 55 Dahua Network Camera Web 3.0 Operation Manual Figure 5-21 Please refer to the following sheet for detailed information. Parameter Function  Here you can privacy mask the specified video in the Privacy Masking monitor video.  System max supports 4 privacy mask zones.
  • Page 56 Dahua Network Camera Web 3.0 Operation Manual  Check “Enable” to display the counting statistics data in Counting the video monitoring window; check “Disable” not to display.  There are enter number and leave number for statistics type and left align and right align for OSD info.
  • Page 57 Dahua Network Camera Web 3.0 Operation Manual Figure 5-23 Parameters Note Check “Enable”, then it will display the ROI in the video monitoring window; Enable Check “Disable”, then it won’t display.  Set the image quality of ROI, ranging from 1～6, default is 6.

  • Page 58: Audio

    Dahua Network Camera Web 3.0 Operation Manual Figure 5-24 5.1.3 Audio Please note some series devices do not support audio function. 5.1.3.1 Audio Figure 5-25 The audio interface is shown as below. See Figure 5-25 Please refer to the following sheet for detailed information.

  • Page 59: Network

    Dahua Network Camera Web 3.0 Operation Manual Parameter Function Enable You can enable audio only when video is enabled. After selecting the “Enable” of main stream or sub stream, the network transmission stream is the audio/video composite stream, otherwise it only includes video image.
  • Page 60 Dahua Network Camera Web 3.0 Operation Manual Figure 5-26 Please refer to the following sheet for detailed information. Parameter Function Host Name It is to set current host device name. It max supports 15 characters. Ethernet Card Please select the Ethernet port. Default is wired.
  • Page 61 Dahua Network Camera Web 3.0 Operation Manual Enable You can use ARP/Ping command to modify or set the device IP ARP/Ping set address if you know the device MAC address. device IP Before the operation, please make sure the network camera address service.

  • Page 62: Connection

    Dahua Network Camera Web 3.0 Operation Manual 5.2.2 Connection Connection 5.2.2.1 Figure 5-28 The connection interface is shown as in Figure 5-28 Please refer to the following sheet for detailed information. Parameter Function It is the max Web connection for the same device. The value ranges from 1 connection to 20.
  • Page 63 Dahua Network Camera Web 3.0 Operation Manual  RTSP port The default value is 554. Please leave blank if use default. User uses QuickTime or VLC can play the following formats. BlackBerry can play too.  Real-time monitoring URL format, please require real-time RTSP media server, require channel no., bit stream type in URL.

  • Page 64: Pppoe

    Dahua Network Camera Web 3.0 Operation Manual Figure 5-29 5.2.3 PPPoE Figure 5-30 The PPPoE interface is shown as in Enter the PPPoE username and password which are provided by ISP (Internet Service Provider), and click “Enable”. The network camera will automatically establish network connection in the mode of PPPoE after it is enabled;...

  • Page 65: Ddns

    Dahua Network Camera Web 3.0 Operation Manual Figure 5-30 5.2.4 DDNS Figure 5-31 The DDNS interface is shown as in The DDNS is to set to connect the various servers so that you can access the system via the server.
  • Page 66 Dahua Network Camera Web 3.0 Operation Manual Parameter Function Server Type You can select DDNS protocol from the dropdown list: CN99 DDNS, NO-IP DDNS, Dyndns DDNS, and Dahua DDNS. The default is Dahua DDNS. Server Address DDNS server IP address CN99 DDNS Server address: www.3322.org...

  • Page 67: Ip Filter

    Dahua Network Camera Web 3.0 Operation Manual Parameter Function Server Type You can select CN99 DDNS protocol Under CN99 DDNS the default server address is “www.3322.org” Server Address Domain Name Self-defined domain name Username The user name you input to log in the server.
  • Page 68 Dahua Network Camera Web 3.0 Operation Manual Figure 5-34 Please refer to the following sheet for detailed information. Parameter Function Input server address and then enable this function. SMTP Server Port Default value is 25. You can modify it if necessary.

  • Page 69: Upnp

    Dahua Network Camera Web 3.0 Operation Manual Parameter Function The send interval ranges from 0 to 3600 seconds. 0 means Interval there is no interval. Please note system will not send out the email immediately when the alarm occurs. When the alarm, motion detection or the abnormity event activates the email, system sends out the email according to the interval you specified here.

  • Page 70: Snmp

    Dahua Network Camera Web 3.0 Operation Manual Figure 5-35 5.2.8 SNMP Figure 5-36 Figure 5-37 The SNMP interface is shown as in The SNMP allows the communication between the network management work station software and the proxy of the managed device. Please install the software such as MG MibBrowser 8.0c software or establish the SNMP service before you use this function.
  • Page 71 Dahua Network Camera Web 3.0 Operation Manual Parameter Function  SNMP Version Check SNMP v1, device only process v1 info.  Check SNMP v2, device only process v2 info.  Check SNMP v3, can set username, password and encryption method. Server calibrate corresponding username, password and encryption method too access device and v1/v2 are unavailable.

  • Page 72: Bonjour

    Dahua Network Camera Web 3.0 Operation Manual Check SNMP v3 version and SNMP port, read community, write community, Trap address, Trap port are same with SNMP v1 and SNMP v2 versions. Only when SNMP version is SNMP v3, users need to configure parameter in chart.

  • Page 73: Multicast

    Dahua Network Camera Web 3.0 Operation Manual Figure 5-38 5.2.10 Multicast Figure 5-39 The multicast interface is shown as in Multicast is a transmission mode of data packet. When there is multiple-host to receive the same data packet, multiple-cast is the best option to reduce the broad width and the CPU load. The source host can just send out one data to transit.

  • Page 74: Qos

    Dahua Network Camera Web 3.0 Operation Manual 5.2.11 802.1x 802.1x (port based network access control protocol) supports manual selection of authentication method to control if device connected to LAN can join the LAN. It well supports authentication, charging, safety and management requirement of network.

  • Page 75: Https

    Dahua Network Camera Web 3.0 Operation Manual Figure 5-41 Please refer to the following sheet for detailed information. Parameter Function Real-time The value ranges from 0 to 63. The router or the switcher can monitor provide different service for various data packets.
  • Page 76 Dahua Network Camera Web 3.0 Operation Manual Figure 5-42 2. Click “Create” and it will pop out the dialog box of “HTTPs”, which is shown in Figure 5-43 Figure 5-43...
  • Page 77 Dahua Network Camera Web 3.0 Operation Manual 3. Fill in corresponding “Country”, “Province” and some other information; click “Create” after filling in. It will show the prompt of “Create Successfully”, which means the server certificate has been successfully created. Note: Make sure the “IP or domain name”...
  • Page 78 Dahua Network Camera Web 3.0 Operation Manual Figure 5-45 6. Double click the downloaded icon of “RootCert.cer”. The system will display the information interface of “Certificate”, which is shown in Figure 5-55.
  • Page 79 Dahua Network Camera Web 3.0 Operation Manual Figure 5-46 7. Click “Install Certificate” and it will pop out the interface of “Certificate Import Wizard”, which is Figure 5-47 shown in...
  • Page 80 Dahua Network Camera Web 3.0 Operation Manual Figure 5-47 8. Click “Next”. Select “Trusted Root Certification Authorities”, which is shown in Figure 5-48...
  • Page 81 Dahua Network Camera Web 3.0 Operation Manual Figure 5-48 9. Click “Next”. The system will display the interface of “Completing the Certificate Import Wizard”, Figure 5-49 which is shown in...
  • Page 82 Dahua Network Camera Web 3.0 Operation Manual Figure 5-49 10. Click “Finish”, and it will pop out the dialog box of “Security Warning”, which is shown in Figure 5-50...
  • Page 83 Dahua Network Camera Web 3.0 Operation Manual Figure 5-50 11. Click “Yes”. It will pop out the dialog box of “Import Successful”, click “Ok” to complete downloading Figure 5-51 certificate, which is shown in Figure 5-51  Please refer to the following steps if you select “Install Signed Certificate”.
  • Page 84 Dahua Network Camera Web 3.0 Operation Manual Figure 5-52 2. Select signed certificate and certificate key path respectively via “Browse”, click “Upload”. 3. Install root certificate, please refer to step 6~11 for more details. 4. Check “Enable HTTPs”, click “Save”. The system will display the dialog box of “Need to reboot the device”, and then the config is valid.

  • Page 85: Event

    Dahua Network Camera Web 3.0 Operation Manual Figure 5-54 Note: “xx.xx.xx.xx” is corresponding to your IP or domain name. 5.3 Event 5.3.1 Video detection 5.3.1.1 Motion Detection Step 1 Select “Setup > Event > Video Detection > Motion Detection’ and the system will display the interface of “Motion Detection”...
  • Page 86 Dahua Network Camera Web 3.0 Operation Manual Figure 5-55 Step 2 Select “Enable” to enable motion detection function. Step 3 Set motion detection area.
  • Page 87 Dahua Network Camera Web 3.0 Operation Manual Click “Setup” and the system will pop out the interface of “Setting Area”, which is shown in Figure 5-56 Figure 5-56 2. Set area name, it is to set valid area of motion detection according to the actual situation, and it can set the value of sensitivity and threshold respectively.
  • Page 88 Dahua Network Camera Web 3.0 Operation Manual Parameter Function Note: Working Period It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”.
  • Page 89 Dahua Network Camera Web 3.0 Operation Manual Parameter Function  Here you can set PTZ movement when alarm occurs. Such as go to preset x when there is an alarm.  The event type includes: preset, tour and pattern. You need to check the box here so that system can backup motion detection Snapshot snapshot file.
  • Page 90 Dahua Network Camera Web 3.0 Operation Manual Parameter Function Note: Working Period It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”.
  • Page 91 Dahua Network Camera Web 3.0 Operation Manual Figure 5-58 Step 2 Check “Enable” to enable the function of scene changing. Step 3 It is to set the parameters of scene changing, please refer to the following sheet for more details.

  • Page 92: Audio Detection

    Dahua Network Camera Web 3.0 Operation Manual Parameter Function If you enabled this function, System can send out email to alert you when Send Email alarm occurs and ends. User can set email address in Network>SMTP.  Here you can set PTZ movement when alarm occurs. Such as go to preset x when there is an alarm.
  • Page 93 Dahua Network Camera Web 3.0 Operation Manual Parameter Function It is to select “Audio Channel 1” or “Audio Channel 2” for detection Audio channel according to the actual needs. Select “Enable Input Abnormal” and it will trigger alarm when it detects Input abnormal audio input abnormity.

  • Page 94: Smart Plan

    Dahua Network Camera Web 3.0 Operation Manual Step 3 Click “Save” to complete the setup of audio detection. 5.3.3 Smart Plan Smart plan is the master switch for intelligent analysis such as “Face Detection”, “Heat Map”, “IVS”, “People Counting” and so on, the corresponding intelligent functions can be valid after smart plan is enabled.
  • Page 95 Dahua Network Camera Web 3.0 Operation Manual  Try to keep away from the areas such as glass, ground reflected light, water surface, branch, shadow, mosquito disturbance and etc. try to keep away from the backlight scene to avoid direct light.
  • Page 96 Dahua Network Camera Web 3.0 Operation Manual Step 4 Click “Draw Target” to draw the size model of filtered target in the video image. Step 5 It is to set the parameters of tripwire, please refer to the following sheet for more details.
  • Page 97 Dahua Network Camera Web 3.0 Operation Manual Click “Save” to complete the setup of tripwire. 5.3.4.2 Intrusion Intrusion includes cross and appears.  Cross means that it will trigger alarm when the target enters or exits the area.  Appears means that it will trigger alarm when the target appears in the area.
  • Page 98 Dahua Network Camera Web 3.0 Operation Manual Click “Draw Target” to draw the size model of filtered target in the video image. Step 5 It is to set the parameters of intrusion, please refer the following sheet for more details.
  • Page 99 Dahua Network Camera Web 3.0 Operation Manual Step 5 Click “Save” to complete the setup of intrusion. 5.3.4.3 Abandoned Object Abandoned object means the system will trigger alarm if the abandoned object in the monitoring scene exceeds the time which has been set by the users.
  • Page 100 Dahua Network Camera Web 3.0 Operation Manual Step 4 Click “Draw Target” to draw the size model of filtered target in the video image. Step 5 It is to set the parameter of abandoned object, please refer to the following sheet for more details.
  • Page 101 Dahua Network Camera Web 3.0 Operation Manual Because the system distinguishes abandoned object from missing object according to the similarity of foreground and background, it may cause error between abandoned object and missing object in a situation where both foreground and background are complicated.

  • Page 102: Face Recognition

    Dahua Network Camera Web 3.0 Operation Manual Parameter Function Note: Working Period It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”.
  • Page 103 Dahua Network Camera Web 3.0 Operation Manual Select “Setting > Event > Face Recognition > Face Detection” and the system will display the interface of “Face Detection”, which is shown in Figure 5-65. Figure 5-65 Step 2 Select ‘Enable” to enable the function of face detection.
  • Page 104 Dahua Network Camera Web 3.0 Operation Manual Parameter Function Select “Enable Face Enhancement” and it will guarantee that the face is Face clear by priority when the stream is set very low. Enhancement Check it and so when alarm occurs, system will auto record.
  • Page 105 Dahua Network Camera Web 3.0 Operation Manual After the face database is successfully configured, it can realize comparison between the detected face and the info in the face database. Step 1 Select ‘Setting > Event > Face Recognition > Face Database Config” and the system will display the interface of “Face Database Config”, which is shown in Figure 5-66.
  • Page 106 Dahua Network Camera Web 3.0 Operation Manual Figure 5-68 Step 4 It is to set the parameters of face database, please refer to the following table for more details. Parameter Note Click “Deploy” and the deployment of face database becomes valid.
  • Page 107 Dahua Network Camera Web 3.0 Operation Manual Step 2 Set the conditions according to actual needs, click “Search”. The system will display the search results. 5.3.5.2.2 Registration Step 1 Click ‘Registration” on the more info interface of face database. The system will display the interface which is shown in Figure 5-70.
  • Page 108 Dahua Network Camera Web 3.0 Operation Manual Figure 5-71 Step 3 Click “Add to task list”. Step 4 Click . The system will display the interface which is shown in Figure 5-72. Figure 5-72 Step 5 Click “OK” and complete registration.
  • Page 109 Dahua Network Camera Web 3.0 Operation Manual 5.3.5.2.3 Batch Registration Step 1 Click “Batch Registration” on the interface of more info for face database config and the system will display the interface which is shown in Figure 5-73. Figure 5-73 Step 2 It is to upload the pictures according to the naming needs required on the interface.
  • Page 110 Dahua Network Camera Web 3.0 Operation Manual Click “Check Details” after batch registration is completed, check registration results. The system will display the interface which is shown in Figure 5-75. Figure 5-75 5.3.5.2.4 Info Modify Step 1 Click “More Info” on the interface of face database config. The system will display the interface which is shown in Figure 5-76.
  • Page 111 Dahua Network Camera Web 3.0 Operation Manual Step 3 Click and the system will display the interface which is shown in Figure 5-78. Figure 5-78 Step 4 It is to modify info according to actual needs. Step 5 Click “Add to task list”.

  • Page 112: People Counting

    Dahua Network Camera Web 3.0 Operation Manual Note Click “Remove All” to remove all the current tasks. 5.3.6 People Counting 5.3.6.1 People Counting Step 1 Select “Setup > Event > People Counting > People Counting” and the system will display the interface of “Entrance/Exit”, which is shown in Figure 5-80.
  • Page 113 Dahua Network Camera Web 3.0 Operation Manual Parameter Function Note: Working Period It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”.

  • Page 114: Heat Map

    Dahua Network Camera Web 3.0 Operation Manual Figure 5-81 Step 2 It is to set search condition, please refer to the following sheet for more details. Parameter Note Can select day report, month report and year report; also can select bar chart or line Report Type chart to display the report.
  • Page 115 Dahua Network Camera Web 3.0 Operation Manual Figure 5-82 Step 2 Select “Enable” to enable heat map function. Step 3 It is to set the working period. 1. Click “Setup” and the system will display the interface of “Working Period”, which is shown in...
  • Page 116 Dahua Network Camera Web 3.0 Operation Manual Figure 5-83 2. It is to set working period according to the following methods:  You can input time numerical value or press the left mouse button to drag on the setup interface to set.

  • Page 117: Alarm

    Dahua Network Camera Web 3.0 Operation Manual It is to set begin time and end time. Step 3 Click “Search” to complete report statistics, click “Export” to export the statistics report. 5.3.8 Alarm Please note some series products do not support this function.
  • Page 118 Dahua Network Camera Web 3.0 Operation Manual Parameter Function After enabling, the system will automatically turn on the flash Flash when alarm occurs. Flash Delay  The flash will be off with a period of time delay when the alarm linkage is over.
  • Page 119 Dahua Network Camera Web 3.0 Operation Manual Figure 5-86 Parameter Function Enable Check it and enable the alarm linkage. Relay-in The default alarm 1，some products can choose alarm 2. Two types of sensor which are normally open (NO) and normally closed (NC), switch from normally open to normally closed, open the alarm.

  • Page 120: Abnormity

    Dahua Network Camera Web 3.0 Operation Manual 5.3.8.3 Audio detection Note: Audio detection won’t work when “Talk” is enabled on the preview interface. Figure 5-88 parameter Function Enable Check it and enable audio detection. It will trigger alarm and set up a series of linkage when volume exceeds the set Threshold threshold.
  • Page 121 Dahua Network Camera Web 3.0 Operation Manual Figure 5-89 Figure 5-90...
  • Page 122 Dahua Network Camera Web 3.0 Operation Manual Figure 5-91 Please refer to the following sheet for detailed information. Parameter Function Check to alarm when SD card is abnormal. Enable Check to enable relay-out alarm. Relay-out Relay out The alarm output can delay for the specified time after alarm stops. The delay value ranges from 10s to 300s.

  • Page 123: Storage Management

    Dahua Network Camera Web 3.0 Operation Manual Figure 5-92 When login password keep been wrong for a few times, unauthorized access alarm occurs. This operation is similar to SD card error. Allow login error times as when it exceeds this limit, user account will be locked.
  • Page 124 Dahua Network Camera Web 3.0 Operation Manual Figure 5-94 Step 2. From Monday to Sunday select record time, click on setup on the right, see Figure 5-95.  Set period according to actual need. There are six periods available each day.
  • Page 125 Dahua Network Camera Web 3.0 Operation Manual Figure 5-96 Step 4. In record schedule interface, click on OK. System prompts it is successfully saved. 5.4.1.2 Snapshot Schedule Snapshot setup as: Figure 5-97 Step 1. Click on Snapshot Schedule tab, see...
  • Page 126 Dahua Network Camera Web 3.0 Operation Manual  By checking or unchecking, user can add or delete three types of snapshot schedule: General, Motion and Alarm. Note: Period setup can be done by dragging in snapshot schedule interface while not releasing left mouse.

  • Page 127: Destination

    Dahua Network Camera Web 3.0 Operation Manual 5.4.1.3 Holiday Schedule Holiday schedule can set specific date as holiday. Figure 5-100 Step 1. Click on Holiday Schedule tab, see Figure 5-100 Step 2. Select date to set as holiday. The selected date will be highlighted in yellow.
  • Page 128 Dahua Network Camera Web 3.0 Operation Manual Figure 5-101 Please refer to the following sheet for detailed information. Parameter Function Event It includes: scheduled, motion detect and alarm. Type Local It saved in the SD card. It saved in the FTP server.
  • Page 129 Dahua Network Camera Web 3.0 Operation Manual 5.4.2.3 FTP Figure 5-103 The FTP interface is shown as in You need to check the box to enable the FTP function. When network disconnect occurred or there is malfunction. Emergency storage can save the record/snapshot picture to the local SD card. Click the test button to check if the FTP server can be connected for test.

  • Page 130: Record Control

    Dahua Network Camera Web 3.0 Operation Manual 5.4.3 Record control Figure 5-105 The record control interface is shown as in Figure 5-105 Please refer to the following sheet for detailed information. Parameter Function Here you can select file size within 1min~120min. Default setup is 8 Pack minutes.
  • Page 131 Dahua Network Camera Web 3.0 Operation Manual Figure 5-106 Please refer to the following sheet for detailed information. Parameter Function It is to set device name. Device Note: Different devices have different names. Name Video This is to display video standard such as PAL.

  • Page 132: Account

    Dahua Network Camera Web 3.0 Operation Manual Figure 5-107 Please refer to the following sheet for detailed information. Parameter Function Here you can select date format from the dropdown list. Date format There are two options: 24-H and 12-H. Time Format The time zone of the device.
  • Page 133 Dahua Network Camera Web 3.0 Operation Manual  For user name and user group, the max length is 31 characters, which can be made up of digit, letter, underline, hyphen, dot and @.  Password can be 0~32 characters in number and letter only. User can modify other user’s password.
  • Page 134 Dahua Network Camera Web 3.0 Operation Manual Figure 5-109 Modify user Figure 5-110 It is to modify the user property, belonging group, password and rights. See Modify password It is to modify the user password. You need to input the old password and then input the new password twice to confirm the new setup.
  • Page 135 Dahua Network Camera Web 3.0 Operation Manual Figure 5-110 5.5.2.2 Group The group management interface can add/remove group, modify group password and etc. Figure 5-111 The interface is shown as in Figure 5-111 Figure 5-112 Add group: It is to add group and set its corresponding rights. See...
  • Page 136 Dahua Network Camera Web 3.0 Operation Manual Please input the group name and then check the box to select the corresponding rights. It includes: preview, playback, record control, PTZ control and etc. Figure 5-112 Modify group Figure 5-113 Click the modify group button, you can see an interface is shown as in Here you can modify group information such as remarks and rights.

  • Page 137: Default

    Dahua Network Camera Web 3.0 Operation Manual 5.5.3 Default Figure 5-114 The default setup interface is shown as in Please note system cannot restore some information such as network IP address, account and so on. Figure 5-114 5.5.4 Import/Export Figure 5-115...

  • Page 138: Remote Control

    Dahua Network Camera Web 3.0 Operation Manual 5.5.6 Remote control Note: It is supported by some devices. Figure 5-116 Parameter Function Learn Bind remote control or wireless alarm with equipment. Clear Unbind remote control with equipment. Start arm after the time you choose, disarm comes into effect immediately. Note: Arm/Disarm With disarm status, all the following alarms won’t trigger: motion detect alarm,...

  • Page 139: Upgrade

    Dahua Network Camera Web 3.0 Operation Manual Figure 5-117 Parameter Function Auto Reboot Check it and set auto reboot time. Auto Delete Old Check it and set period within 1~31 days. Files 5.5.6 Upgrade Figure 5-118 The upgrade interface is shown as in Please select the upgrade file (file extension is “.bin”) and then click the update button to begin firmware...

  • Page 140: Log

    Dahua Network Camera Web 3.0 Operation Manual 5.6.2 Log Figure 5-120 Here you can view system log. See Figure 5-120 Please refer to the following sheet for log parameter information. Parameter Function Set the start time of the requested log. (The earliest time is 2000/1/1) Start time Set the end time of the requested log.
  • Page 141 Dahua Network Camera Web 3.0 Operation Manual Figure 5-121...

  • Page 142: Alarm

    Dahua Network Camera Web 3.0 Operation Manual 6 Alarm Please note some series product does not support this function. Figure 6-1 Click alarm function, you can see an interface is shown as in Here you can set device alarm type and alarm sound setup.
  • Page 143 Dahua Network Camera Web 3.0 Operation Manual Type Parameter Function Operation Prompt When alarm is triggered, there will be s inmain menu of alarm interface and system automatically records alarm info. The icon disappears when user click on alarm menu bar.

  • Page 144: Log Out

    Dahua Network Camera Web 3.0 Operation Manual 7 Log out Figure 7-1 Click log out button, system goes back to log in interface. See Figure 7-1 Note  This manual is for reference only. Slight difference may be found in user interface.

Table of Contents