Danfoss VLT AQUA Drive FC 202 Operating Manual page 104

Specifications
10.1.3 Electrical Data for Enclosures D1h–D8h, 3x525–690 V
®
VLT AQUA Drive FC 202
High/normal load
(High overload=150% current during 60 s.
Normal overload=110% current during 60 s)
Typical shaft output at 525 V [kW]
Typical shaft output at 575 V [hp]
Typical shaft output at 690 V [kW]
Enclosure size
Output current (3-phase)
Continuous (at 525 V) [A]
Intermittent (60 s overload) (at 525 V) [A]
Continuous (at 575/690 V) [A]
Intermittent (60 s overload)(at 575/690 V) [A]
Continuous kVA (at 525 V) [kVA]
Continuous kVA (at 575 V) [kVA]
Continuous kVA (at 690 V) [kVA]
Maximum input current
Continuous (at 525 V) [A]
Continuous (at 575/690 V)
Maximum number and size of cables per phase
- Mains, motor, brake, and load share [mm
Maximum external mains fuses [A]
Estimated power loss at 575 V [W]
10 10
Estimated power loss at 690 V [W]
Efficiency 3)
Output frequency [Hz]
Heat sink overtemperature trip [°C (°F)]
Control card overtemperature trip [°C (°F)]
Table 10.5 Electrical Data for Enclosures D1h/D3h/D5h/D6h, Mains Supply 3x525–690 V AC
1) For fuse ratings, see chapter 10.7 Fuses and Circuit Breakers.
2) Typical power loss is at normal conditions and expected to be within
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies to
dimensioning of drive cooling. If the switching frequency is higher than the default setting, the power losses can increase. LCP and typical control
card power consumptions are included. For power loss data according to EN 50598-2, refer to www.danfoss.com/vltenergyefficiency. Options and
customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B each add only 4 W.
3) Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy
efficiency class, see chapter 10.4 Ambient Conditions. For part load losses, see www.danfoss.com/vltenergyefficiency.
102
VLT® AQUA Drive FC 202
HO
45
60
55
76
114
73
110
69
73
87
74
70
2x95 (2x3/0)
2
(AWG)]
1)
2), 3) 1098
1057
2), 3)
110 (230)
75 (167)
Danfoss A/S © 09/2018 All rights reserved.
N75K N90K
NO HO
55 55
75 75
75 75
D1h/D3h/D5h/D6h
90 90
99 135
86 86
95 129
82 82
86 86
103 103
87 87
83 83
2x95 (2x3/0)
160 315
1162 1162
1204 1205
0.98 0.98
0–590 0–590
110 (230)
75 (167)
± 15% (tolerance relates to variety in voltage and cable conditions). These
N110
NO HO NO
75 75 90
100 100 125
90 90 110
113 113 137
124 170 151
108 108 131
119 162 144
103 103 125
108 108 131
129 129 157
109 109 132
104 104 126
2x95 (2x3/0)
315
1428 1430 1740
1477 1480 1798
0.98
0–590
110 (230)
75 (167)
MG21A502