Rear Panel Connections - Extron electronics DXP 44 HD 4K PLUS Setup Manual

DXP HD 4K PLUS Series • Setup Guide (Continued)
Download the PCS program from www.extron.com.
6.
Select EDID files to apply to inputs as desired, using PCS (see the DXP HD 4K PLUS Help file for details).
7.
Create ties and presets as desired (see
8.

Rear Panel Connections

Most of the connectors are on the rear panels of the DXP HD 4K PLUS. Figure 2 shows the rear panel of DXP 88 model.
CAUTION: Remove power from the system before making any connections.
ATTENTION : Couper l'alimentation avant de faire l'installation électrique.
ATTENTION:
• Use electrostatic discharge precautions (be electrically grounded) when making connections. Electrostatic discharge
(ESD) can damage equipment, although you may not feel, see, or hear it.
• Prenez des précautions contre les décharges électrostatiques (soyez électriquement relié à la terre) lorsque vous
effectuez des connexions. Les décharges électrostatiques (ESD) peuvent endommager l'équipement, même si vous ne
pouvez pas le sentir, le voir ou l'entendre.
100-240V ~ 1.0A MAX
100-240V ~ --A MAX
1 2
1 2
5 6
5 6
50-60 Hz
50-60 Hz
I I
Input connectors
A
Output connectors
B
Reset LED
C
DXP 88 HD 4K PLUS Rear Panel
Figure 2.
NOTE:
Figure 2 shows the DXP 88 HD 4K, with 8 inputs and 8 outputs. The rear panels of the DXP 44, 84, and 88 are
identical except for the number of inputs and outputs.
Input connectors — Connect HDMI sources to these female 19-pin type A HDMI input connectors for video input.
A
LockIt™ cable lacing brackets, one for each HDMI input and output connector, are provided with the
DXP HD 4K PLUS. These brackets can be used to secure the HDMI cables to the DXP connectors to reduce stress
on the HDMI connectors and prevent signal loss due to loose cable connections (see
LockIt HDMI Cable Lacing Bracket
Output connectors — Connect HDMI output devices to these female 19-pin type A HDMI output connectors for
B
buffered video output (see
Reset LED — While you are holding the Reset button, this green LED blinks every 3 seconds to indicate the
C
level of reset that will occur if the button is released at that point (see figure 2,
Reset button — This recessed button initiates four levels (modes) of reset. Use a pointed object such as a small
D
screwdriver to press and hold the Reset button.
Factory firmware reset (mode 1) — Hold the Reset button while powering up the switcher to restore the DXP to
•
the factory firmware for a single power cycle. This type of reset maintains all the current user settings, such as audio
adjustments, IP settings, and the configuration.
IP settings reset (mode 4) — While the DXP is running, press and hold the Reset button until the LED blinks twice
•
(approximately 6 seconds). Release the button and press it again momentarily to reset the switcher IP functions. This
reset does not replace any user-installed firmware.
Absolute reset (mode 5) — While the DXP is running, press and hold the Reset button until the LED blinks three
•
times (approximately 9 seconds). Release the button and press it again momentarily to restore the switcher to the default
factory conditions.
2
Creating Ties
A A
3 4
1
3
4 1
7 8 5
7 8 5
Reset button
D
Remote RS-232 connector
E
LAN port
F
on page 4).
Securing HDMI Cables with the LockIt HDMI Cable Lacing
on page 6 and Saving or Recalling a Preset
B B
S/PDIF
3
2 4 S/PDIF
2 3 4
6 7 8
6 8
7
H H
Analog audio outputs
G
S/PDIF audio outputs
H
AC power connector
I
, Reset button).
D
on page 7).
C C D D D D
DXP 88 HD 4K PLUS
DXP 88 HD 4K PLUS
1
1
REMOTE LAN
REMOTE LAN
L R
L R RS-232
RESET
Tx Rx G
RESET
Tx Rx G
2
2
F F
G G E E
Securing HDMI Cables with the
Bracket).
1
1
RESET