Table of Contents
Advertisement
Air conditioner registration
Paring Method
Choose from the following modes to connect your Air conditioner to your Wireless LAN router.
Note:
Before starting this setting, wait for 60 seconds or more after the power supply is connected to the air conditioner (via breaker or plug).
If both LED 1 and 2 are off, the WLAN adapter may be in Sleep mode. Be sure it is deactivated before setting up the wireless LAN. (Refer to "SETTING MANUAL")
Check that the smartphone or tablet PC is linked to the wireless router you are connecting the air conditioner.
The setting will not work if it is not connected to the same wireless router.
The display screen design may differ depending on the version of the mobile app.
To control 2 or more air conditioners with the same smartphone or tablet PC, repeat the setup of the chosen mode.
Button Mode
*Lighting pattern:
OFF
ON
1
Launch the mobile app(FGL air).
2
Sign in with your Email address and
password (as registered in "4.2.
User registration") following the
screen on the mobile app.
3
Press the [+] button to add a new
air conditioner.
4
Confirm that LED 2 is flashing.(On/
off at 2-second intervals.) Then se-
lect [Button mode] on the screen.
If LED 1 and 2 are off, push the Setting button
once.
(Refer to "5. SLEEP MODE" SETTING MANUAL)
5
Press the WPS button on the wire-
less router that you are connecting
to.
Refer to the operating manual of the wireless
router for the location of the button and how to
press it.
6
Confirm that LED 2 is flashing.
(On/off at 2-second intervals.)
Then press and hold the Setting
button on the WLAN adapter for 3
seconds.
LED 2 lighting will change.
(on/off: 2sec/2sec → 2sec/0.5sec)
Confirm that the LED 1 and 2 is
both on to proceed.
7
Press [Register] to start the connec-
tion with the wireless router.
LED 1 and 2 will both flash 2 times,
and a message will appear when
setup is complete.
Flashing
FGL air
john@fgl.com
Sign in
+
Button mode
Manual mode
(on/off=2sec/2sec)
Wireless router
(on/off = 2sec/2sec)
(on/off=2sec/0.5sec)
Register
Registration
Successful!
Manual mode
*Lighting pattern:
1~3
See steps 1 to 3 in "4.3.1. Button mode"
4
Select [Manual mode].
If LED 1 and 2 are off, push the Setting button
once. (Refer to "5. SLEEP MODE" SETTING MANUAL )
[For Android]
5
Select the SSID of the air condition-
er you are connecting to.
6
Input the PIN code written on the WLAN
label.
7
Select the SSID of the wireless rout-
er you are connecting to.
Input the wireless router (WLAN
access point) password then press
[Connect device].
8
LED 1 and 2 will both flash 2 times,
and a message will appear when
setup is complete.
[For iOS]
5
Select [Open W-LAN setting] or
activate the wireless LAN by press-
ing the Home button -> [Setting] ->
[Wi-fi ].
Select the SSID of the air condition-
er you are connecting to.
6
Input the PIN code written on the WLAN
label.
7
Select the SSID of the wireless rout-
er you are connecting to.
Input the wireless router (WLAN
Access Point) password then press
[Connect device].
LED 1 and 2 will both flash 2 times,
and a message will appear when
setup is complete.
(2 times)
02-37
OFF
ON
Flashing
Button mode
Manual mode
Selected router
AC-UTY-xxxxxxxxxx
Enter
password
Connect device
Selected router
Select the WLAN
Access Point
Enter
password
Home AP
XYZ AP
Connect device
ABC123
Registration
Successful!
(2 times)
Open W-LAN setting
AC-UTY-xxxxxxxxxx
continue
Selected router
AC-UTY-xxxxxxxxxx
Enter
password
Connect device
Selected router
Select the WLAN
Access Point
Enter
password
Home AP
XYZ AP
Connect device
ABC123
Registration
Successful!
(2 times)
Advertisement
Table of Contents
Troubleshooting
