How To Clean; Management After Hatching; Dew Condensation; How To Separate And Clean - Rcom PRO PLUS 10 User Manual

North America Sales & Service www.RcomCo.com
▶ The humidity control is important in 1-2 days before hatching than in the beginning and in the middle of incubation, the moisture must be maintained
from
1-2 days before hatching. In case of water bird the humidity during incubation must be RH 45~55% / in case of poultry RH 40~45% / parrots RH 35~45%
generally and for every type of bird the humidity for a day before hatching must be RH 65% or over.
※ Air control lever (Air Vent) : It may induce the fresh exterior air minimizing the effects on the insulation.
Verify once every 3 days during the incubation if the water is low, then supply water, and it is recommended to use distilled or purified water than water
from water purifier, softener or underground water to maintain performance.
※ The humidity pad is consumable and it can be purchased.

Management after hatching

▶ Hatching within the incubator can cause a build up of germs with possible cross contamination of bacteria, and the dust, feather dander, egg shells and
excrement may produce a breakdown of the incubator which is not covered under warranty. Please consider the Rcom Suro eco hatcher specifically for
hatching. We recommend to use the KINGSURO Brooder of our company for brooding.
Do not brood the chick within the incubator. Have a radiant heat brooder for chicks that are dry and fluffy.
As it can be the cause of breakdown and produce paid repair (A/S) cost even within warranty period. (Please move the chick to the brooding chamber
after hatching
Generating chamber: It is a space for hatching (egg breaking) used 1~3 days before hatching. (RCOM KINGSUR BROODER)
Developing (brooder) chamber: It is a space (device) which adapts the just born chick to the environment by maintaining proper temperature and
humidity. (Rcom KINGSUR BROODER/Rcom BIRD BROODER&ICU)
▶ As the feed for little birds may vary by type, it is recommendable to acquire prior understanding on the bird before hatching.
(Please use the information on birds in the Rcom web site.)

Dew Condensation

▶ When operating the device, if the difference between exterior and interior temperature of the device is high, the dew condensation is naturally occurred
therefore there is no operational problem due to this phenomena.

4. HOW TO CLEAN

How to separate and clean

Please separate the power cord from the socket.
▶ When immediately turned off the device in high humidity
incubation and left with the cover closed, the humidity
remaining inside the device may evaporate, adhere to the
device and product breakdown. Always open the view-
window and eliminate the inner humidity to use the
device in the most safe manner. Incubator must be
completely dried out before storage.
▶ There are 3 hooks connected with the main controller in the
inner part of the view-window. Push the 3 hooks to the inner
side and separate the main controller and the view-window.
▶ Eliminate carefully with brush the dust on the separated main
controller. At this point, do not apply any strength on the
sensor or heater.
▶ The humidity and temperature sensor units are connected
with the connector to be easily replace in case of breakdown.
▶ Wipe the view-window, egg rotation disk, tray, air filter and
the main body (lower part) down properly with lukewarm water.
▶ Do not was the Automatic Pumping System (APS) with water
but wipe with clean fabric.
▶ Wipe the exterior with smooth fabric, dry in a fresh place with proper ventilation and
assemble in order reverse to the disassembly and store properly.
Do not clean the product with organic solvents as benzene and thinner.
It may deform or discolor the product.
Rcom Bird Egg Incubator Eco Pro Plus 10 User Manual
Please open all the air control levers (Air Vent) when the egg breaking begins.
(1) How to disassemble and clean