Rcom KingSuro ECO 20 User Manual

North America Sales & Service www.RcomCo.com
Rcom KINGSURO ECO 20 MANUAL Rcom KINGSURO ECO 20 MANUAL

1. Safety Precautions

Electrical hazards
Do not use a damaged Do not pull the cord when
power cord or loose taking out the power cord,
and keep wet hands away
outlet.
from connecting plug.
Risk of electric shock or fire. Risk of electric shock or fire.
Setting Cautions
Do not install in dusty or Do not install under the
dirty environment. direct sunlight.
Risk of damage or fire within Risk of fire or interference with
the incubator. the incubation process.
Do not cover the Install away from heat
ventilating opening. sources.
Inner temperature can rise, Risk of damage to the incubator
case and interference with
interrupting incubation.
the incubation process.
Do not disassemble or Please ensure that no
modify the incubator in small objects get into
any way. the holes on the incubator.
Risk if electric shock or fire. Risk of electric shock or fire.
Cleaning Cautions
Do not spray cleanser Clean the incubator by a
directly on the incubator soft cloth with a neutral
surface. detergent.
※ This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.

2. Identification of Parts

View-Window
ABS Divider
Bottom Body
3. Basic components
Your Serial no. located on left-side of the main controller. Please be sure not to get dirty or break.
(ex:RCM0950278)
Rated voltage and product serial No. are marked inside of power cover.
Be sure to check this before connecting power.
(Power Cap)
Main Controller View-Window
(1pcs.)
(2pcs.)
Power Cover fixing bolt
Main Controller Assembly Bolts
(6pcs.)
ABS Divider
Power Cord
(125mm)
Thermometer Nipple (1pcs.)
When the spirit thermometer from KingSuro ECO has an inaccurate reading (separations look like blue dots)
caused by transit, please dip the thermometer in very warm water. When the thermometer spirit reaches
maximum, please take the thermometer out of the warm water. Please check the spirit has joined together.
The dipping method may need to be repeated to remove separations in spirit. At this time, if the water is too
hot or maximum temperature is kept for a long time, it may cause malfunction of the thermometer.
Rcom Bird Egg Incubator KingSuro Eco 20 User Manual
EX-SURO
Be careful the details below when you use.
Never pull the plug out of Do not twist or crush Do not insert multiple
the outlet during the electric cord. connecting plugs in an
incubation period. outlet.
Risk of fire or electrical overload.
Incubation will be interrupted. Risk of electric shock or fire.
Be careful the details below when you use.
Do not install in moist or Do not install in excessively Do not use any other
humid environment. cold or hot conditions, non-standard parts
cigarette smoke, etc. except those provided.
Risk of fire or electric shock. Risk of interference with Risk of damage or hatching
the incubation process. failure.
Children should be supervised
Ensure that the incubator is Do not turn the incubator
to ensure that they do not play
installed on a stable surface upside down.
away from edges. with the appliance.
Risk of damage to incubator Water will pour out of the incubator, Risk of knocking the incubator
and eggs and user from and view window can be dropped or accidental interference with
accidental knocks or drops. or damaged. the controls.
If the incubator sounds Clean the incubator If the incubator requires
strange or emits smoke
thoroughly before storing. repair disconnect from the
contact your service
power supply and please
center.
contact to your service center.
Risk of electric shock or fire.
Be sure to disconnect the electric cord
from the outlet before cleaning.
Brush away dust on the Do not use chemicals like wax, For special cleaning of
plug with a dry cloth. benzene, alcohol, thinner, inner part per year, contact
to the service center.
aromatic, or lubricant, etc.
If you don't clean the inside of
incubator for a long time, dust
can cause some trouble or a fire.
Main Controller Power Cab
Air Ventilation
Egg Tray
Egg Turning Wire
Egg Tray Bottom Body
(2pcs.)
V-Pin Egg Turning Wire
(210mm * 150mm)
Manual Humidity Pad
(100mm)
Silicon Tube Humidity Injector
4. Display
①
● Name & Function of operation Parts
① Heater Operation Lamp
- Light on when working
5. How to Assemble (Before Using)
1
▶ Please remove all packing from the incubator and
parts. Then, check each part is present and
undamaged. (Please keep the carton and packing
materials for repacking to retain the incubator in good
condition when not using.)
▶ Loose 2 screws, connecting Main-controller and
3
View-window. And then, disassemble Main-controller
and View-window by pushing out 4 hooks on
Main-controller.
▶ Fix silicone tube which is assembled with nipple into the
hole.
Be careful to ensure the silicon tube is not folded.
▶ Insert the nipple into the holder, located
4
on edge of main controller, and assemble
View-window and main controller with
2 screws
Please do not tighten the screws
too much.
5 How to cut and fold the Humidity pad properly.
50mm X 150mm
(Low Humidity Use : When using under 60% Humidity setting)
110mm X 150mm
(High Humidity Use : When using over 60% Humidity setting)
After cutting the Humidity pad as above sizes for your
purpose, fold up as below picture and insert it with 2 of V-pins.
Humidification ability is different as the pad sizes.
Please make sure that the silicon tube end is located
onto the Humidity pad.
▶ Please change the '50mm X 150mm sized humidity pad' to '110mm X 150mm sized pad' about
3 days before bird hatching to give much more humid environment inside of the incubator.
※ The 'use by' of Humidity pad is about 4~6 months, but if you use dirty water, the life of pad will be short.
(Using Distilled-water strongly recommended) Humidity pad can be purchased separately again from our shop.
▶ Please put about 100mm long silicon tube to the other end of the silicon tube nipple, made of plastic,
located outside of the incubator as below picture.
(2pcs.)
6
▶ Please put the thermometer to the V-pin as right picture.
If you push too strong to put the thermometer into the
V-pin, the thermometer can be broken.
Please make sure to put the thermometer just like right
picture. The sensing part of the thermometer has to be
same side with the picture. Also, the thermometer must
not be touched with Humidity pad for exact temperature
read.
Hatching Pad
7
▶ Please assemble Bottom-body, Tray, and Hatching-pad
order.
Screw Driver Ensure the Hatching-pad is placed on the Tray.
After hatching finished, be sure to wash and dry the
Hatching-pad completely for next use.
Please keep the hatching pad, and if not using the pad
during incubation, the hatching rate will be lower.
② Temperature Control Regulator
- Using screw driver and turn to "+" to make
Temp. Up, and "-" to make Temp. Down.
2
▶ Please put the Egg-Turning wires in the
holes, bottom outside of the main body.
Nipple
High
Humidity Use
110mm
※ Sensing part of the thermometer
has to be located opposite side with
the silicon tube out.
Ver E 1.0
②
Low
Humidity Use
50mm 50mm
100mm