Rcom PRO PLUS 10 User Manual page 21

North America Sales & Service www.RcomCo.com
Do not brood the chick within the incubator. Have a radiant heat brooder for chicks that are dry and fluffy.
As it can be the cause of breakdown and produce paid repair (A/S) cost even within warranty period. (Please move the chick to the brooding after
hatching
Generating chamber: It is a space for hatching (egg breaking) used 1~3 days before hatching. (RCOM KINGSURO BROODER)
Developing (brooder) chamber: It is a space (device) which adapts the just born chick to the environment by maintaining proper temperature and
humidity. (Rcom KINGSURO BROODER/Rcom BIRD BROODER&ICU)
▶ As the feed for little birds may vary by type, it is recommendable to acquire prior understanding on the bird before hatching.
(Please use the information on birds in the Rcom web site.)
Dew Condensation
▶ When operating the device, if the difference between exterior and interior temperature of the device is high, the dew condensation is naturally occurred
therefore there is no operational problem due to this phenomena.
4. HOW TO CLEAN
How to separate and clean
Please separate the power cord from the socket.
▶ When immediately turned off the device in high humidity
incubation and left with the cover closed, the humidity
remaining inside the device may evaporate, adhere to the
device and produce breakdown. Always open the view-
window and eliminate the inner humidity to use the device in the
most safe manner.
▶ Thoroughly clean and dry before storage.
▶ Use the screwdriver and separate the thermometer from the
thermometer holder.
▶ There are 3 hooks connected with the main controller in the
inner part of the view-window. Push the 3 hooks to the inner
side and separate the main controller and the view-window.
▶ Carefully remove the dust on the separated main controller
with a brush. At this point, do not apply any force on the
sensor or heater.
▶ The humidity and temperature sensor units are connected
with the connector are easily replace in case of breakdown.
▶ Wipe the view-window, egg rotation disk, tray, air filter and
the main body (lower part) down properly with lukewarm water.
(Turning disk, egg tray and air filter are optional for ECO 10.)
▶ Polish the exterior with smooth fabric, dry in a fresh place with proper ventilation and
assemble in order reverse to the disassembly and store properly.
Do not clean the product with organic solvents as benzene and thinner.
It may deform or discolor the product.
5. PRODUCT INFORMATION
FAQ
The Rcom products are manufactured under strict quality management with precise equipments, but there may be some defects in the product during the
distribution. If there is any problem please contact to the Service center or Distributor of RCOM. We will do our best to resolve the problem as soon as
possible. The product is designed in module methods which is easily replaceable by any qualified person.
Symptom
If the average hatching
rate is low
Rcom Bird Egg Incubator Eco Pro Plus 10 User Manual
Estimated cause (possibility)
▶ If the egg is unfertilized
▶ Germ infection
▶ Incorrect incubation setup
▶ Health condition of the mother bird
▶ Improper egg rotation
▶ When the vibration or noise is severe near the device
▶ When the air filter's cleaning condition is improper
▶ Improper egg storage status, when passed over 1 week
after spawning
(1) How to disassemble and clean
(1) FAQ / (2) Troubleshooting and measures
Solutions
▶ Candle the egg to verify if it's alive
▶ Sterilize the device
▶ Check all the setup process of the device. Especially on the
temperature.
▶ Care the mother bird's health.
▶ Verify if the egg rotation is normally performed.
▶ Move the device to a place without noise or vibration.
▶ Clean the air filter.
▶ Store the egg under low temperature of 20~25°C or less
and use eggs within 1 week after spawning.