How To Setup Temperature; Termination Of Hatching; Humidity And Ventilation Control During Incubation - Rcom PRO PLUS 10 User Manual

North America Sales & Service www.RcomCo.com
▶ Do not overfill the water hole of the main body (lower part). The connected silicone hose
will
supply water to the interior.
▶ Verify daily if there is water in the water hole during incubation and supply when low.
▶ When desiring to incubate with low humidity only fill the internal water chamber A
connected
to the water hole. [RH 45% or less]
If the humidity of hatching chamber is high please open the air control lever slightly.
▶ When desiring to incubate with high humidity, please fill all the A and B water chambers
with
water. [RH 45% or over]
Adjust as high humidity from 3 days before hatch.
If the humidity of hatching chamber is low please close the air control lever.
(Reference the humidity and ventilation control during incubation)
As the automatic humidity adjustment is unavailable in ECO model, the humidity may not
be adjusted as desired according to the nearby environment.

How to setup temperature

▶ When adjusting to desired temperature, use the screwdriver included in the product by
turning the temperature adjustment volume to control the internal temperature.
[Recommended incubation temperature : 37.5℃ (99.5℉)]
Using a non designated screwdriver may forcibly turn the temperature adjustment volume which may damage adjustment feature. Warranty is invalid.
The temperature adjustment is sensitive, please turn it slightly. (Please read the scale of the thermometer 10 minutes after one adjustment.)
Do not put eggs into incubator, until temperature is stabilized for 1~2 hours and then perform the temperature adjustment by increasing slightly from
low
temperature.

Termination of hatching

▶ There is no power switch in this device.
The device is turned OFF when power disconnected after hatching all the eggs.
3. INCUBATION / FUNCTION SETUP

Humidity and ventilation control during incubation

▶
Humidity must be maintained before hatching to prevent drying of egg shell or non hatch.
▶
It is not recommended to open the cover frequently in the hatching period.
If the cover is frequently opened the humidity is rapidly reduced and it may take long time
recover the humidity again.
※ If the internal temperature of the device is 37℃ (98.6℉) or over, and the temperature of
hatching room is lower then humidity may not reach RH 65%. There might be ±5% of
tolerance in humidity and there is no significant problem for hatching.
▶ The humidity control is important in 1-2 days before hatching than in the beginning and in the middle of incubation, the moisture must be maintained
from
1-2 days before hatching. In case of water bird the humidity during incubation must be RH 45~55% / in case of poultry RH 40~45% / parrots RH 35~45%
generally and for every type of bird the humidity for a day before hatching must be RH 65% or over.
※ Air control lever (Air Vent) : It may induce the fresh exterior air minimizing the effects on the insulation.
Verify once every 3 days during the incubation if the water is low, then supply water, and it is recommended to use distilled or purified water than water
from water purifier, softener or underground water to maintain performance.
※ The humidity pad is consumable and it can be purchased.
Management after hatching
▶ Hatching within the incubator can cause a build up of germs with possible cross contamination of bacteria, and the dust, feather dander, egg shells and
excrement may produce a breakdown of the incubator which is not covered under warranty. Please consider the Rcom Suro eco hatcher specifically for
hatching. We recommend to use the KINGSURO Brooder of our company.
Rcom Bird Egg Incubator Eco Pro Plus 10 User Manual
Please open all the air control levers (Air Vent) when the egg breaking begins.
(2) Moist and ventilation during incubation /
(3) Management after incubation / Dew condensation