Operation - Farfisa EH9262CW series Technical Manual

INTERNAL STATIONS

OPERATION

Call from the door station
When a call is made from the external station,
the videointercom speaker receives the rings
(according to programming), the green LED
starts flashing and the calling user is displayed
on the screen for around 30 seconds. Also the
red LED flashes if the ring has been
deactivated. If the call time has expired and the
videointercom has turned OFF, press the button
" " to reconnect with the calling external
station.
To start the conversation with the external sta-
tion for once of around 90 seconds, press the
button; the green LED goes ON.
If it is desired to disable the audio to the door
station, but continuing hearing the audio from
the door station press shortly the button
this status the red LED will light up continuously.
To restore the audio to the door station press
again the button ; the red LED will recover
the previous status.
In case of a call to a user with more than one
videointercom in parallel installed in the apart-
ment, all the videointercom will ring, but only the
videointercom with internal address 000 will
turn ON. You can answer from this videointercom
by following the instructions above. From oth-
ers videointercoms it is possible to answer by
pressing button . This operation will auto-
matically turn ON this videointercom and will
turn OFF the intercom that had been turned ON
before. If, before answering, you wish display
who is ringing, press the button
button .
To operate the electric door lock release press
the button .
To end the communication and switch OFF the
video intercom press the button
LED goes OFF.
The video intercom switches OFF automatically
when the communication time expires.
Monitor function and connection with one
or more external stations.
With the system in stand-by and no conversation
in progress, it would be possible to monitor the
external door stations by pressing on the
videointercom the button or the other buttons
previously programmed for this function.
If the installation includes more external stations
and button " " is programmed correctly, you
can monitor the external stations (max. 4) in
sequence by pressing the same button again
and again.
The videointercom will be turned ON for about
30 seconds. The monitoring will be interrupted
in case of request of monitor service by another
user, call between users or from an external
station.
Pressing the button while monitoring,
automatically the communication with the
external door stations is enabled.
If after pressing the button
remains switched-OFF and a busy tone is
heard, another conversation is in progress and
it is necessary to wait until the system becomes
free.
Making or receiving a call from another
user.
When the installation is in stand-by, you can
make a call to another user. You must have
stored the address of the desired user's in the
numerical buttons.
Before making a call press the button
you get a busy tone, wait until the system
becomes free; if you get a free tone it is
possible to make a call by pressing the proper
button. After pressing the button you will get a
calling tone on the loudspeaker, while the
videointercom of the called user rings (without
switching-ON) with the programmed melody.
; in
If the called user answers within 30 seconds,
a 90-second conversation starts, otherwise
the system goes back to free.
The internal conversation in progress will be
automatically interrupted in case of call from
external station to any other user.
Making or receiving an intercom call in
your apartment.
When the system is in stand-by it would be
possible to make a local intercommunicating
call to all the videointercoms installed in the
apartment (max 7 monitors with internal
address from 000 to 006) by pressing buttons
previously programmed with code 000.
Before making the internal call press the button
and then the
, if you get a busy tone wait until the system
becomes free; if you get a free tone it is
possible to make an internal call by pressing
the proper button. After pressing the button
you will get a calling tone on the loudspeaker,
; the green
while the videointercom of the called user
rings (without switching-ON) with the
programmed melody. If the called user
answers within 30 seconds, a 90-second
conversation starts, otherwise the system
goes back to free.
The internal conversation in progress will be
automatically interrupted in case of call from
external station to any other user.
the monitor
(MT13 - En 2015)
Tone table
Tone of pressure of a button.
indicate the pressure of the buttons.
Monitor function.
and confirmation of programming value
Communication.
; if
pressure, during the conversation, programming
and attended answer
Activation.
numerical buttons if programmed with actuator
address
Programming.
programming mode
Acknowledge.
programming phase to indicate a valid operation.
System ready.
system is free
0
Calling.
or during an intercommunicating call (active for 30
seconds or until the called user answers).
0
Busy.
busy line
0
Dissuasion.
device is call or when a device is not available
0
End conversation.
before the conversation time ends
0
Note. All the acoustic signalling, with the exception
of the system ready and calling tone, last after
about 2 seconds.
Calling table
1 DIN-DON
2 DRING1
3 DRING2
4 DRING3
5 DRING4
6 MELODY1
7 MELODY2
8 MELODY3
2.
30
It is activated to
Activated on monitor function
Activated on button
Activated on button pressure and
It confirms the beginning of the
It is activated during the
Activated for 30 seconds if the
1 2 3 4
It is activated during a call to another user
1 2 3 4
Activated on pressure of the buttons with
1 2 3 4
It is activated when a non-existent
1 2 3 4
It is activated 10 seconds
1 2 3 4
9 MELODY4
10 MELODY5
11 MELODY6
12 MELODY7
13 MELODY8
14 BEEP
5
5
5
5
5