Main Functions Of Buttons; Programming - Farfisa EH9262CW series Technical Manual

INTERNAL STATIONS

MAIN FUNCTIONS OF BUTTONS

The 4 buttons, located on the front of videointercoms, allow to access the
operating modes, settings and programming of the videointercom. The
functions of the buttons vary according to the operating mode of the
videointercom.
Attention. A dissuasion tone, while pressing a button, means the
function is not available because the service has not been enabled, or the
intercom line is busy.
Videointercom in Stand-By mode (Display OFF)
Settings
Monitor
Contacts (list of door stations or internal users you wish to call)
Videointercom ON and connected to the videointercom line
Videointercom Settings (door station selection and audio-video
adjustments)
Start and close
communication
Muting (enable/disable microphone)
Videointercom ON during setting or programming phase
Cursor Up
Previous page or exit
Cursor Down
Menu
By pressing the menu button it is possible to enter the programming,
settings and adjustment functions of videointercoms.
Present settings are displayed in green.

PROGRAMMING

At the first start-up, the videointercom must be suitably programmed
to define its operating mode. A wrong programming can affect
negatively the operating of the whole system.
The possible programming ways are two:
- remote - it allows to quickly program only the user address of the
intercom by making a call from the door station or the digital
doorkeeper exchanger (refer to the "remote programming" on page
2.18);
- manual - it allows to program all the parameters, by operating
directly on the videointercoms (refer to the "system" on page 2.17).
Programming
User address (mandatory); apartment identification address
(addresses from 1 to 200). It allows to receive an external call or a
Door Lock
call from another device installed in the same building, switch-ON
ok release
the videointercom, have a conversation and open the door lock of
the calling external door station. The address must be the same
address saved in the call button of the push-button panel of the
external door station or in the call button of another intercom device
of the building.
Room number (mandatory in case of multiple devices in the
same apartment); identification address of a device inside the
same apartment (addresses from 0 to 7). The room number
establishes a hierarchy in the internal devices since the device with
room address 0 (zero) will be the main device and all the other
devices will be the secondary lines. Once you have made this
programming, you will be able to make and receive selective calls
with the other devices inside the same apartment. In other words,
each device can individually call the other devices. The external
Door Lock
calls or calls from another apartment will make all devices ringing,
release
ok
the first device that answers the call will activate the conversation
and switch OFF the ringer of the other devices. When you receive
a call from an external door station equipped with camera, all the
devices will ring, but only the main device (room address 0 - zero)
will display the camera image. In this phase you can display the
camera image also from a secondary videointercom without
answering by pressing the camera button "
switch OFF the ringer of all the devices and will display the camera
image on the display of the used videointercom. To answer the call
it is sufficient to press again the button "
ringing only the videointercom to which the call button is physically
connected. To forward the call to the other videointercoms you must
follow the instructions contained in the section "A1 Forward" on
page 2.18.
Next page or
Contacts; it is possible to save the name and the address of:
Enter
ok
- users of other apartments; it allows to call them selectively
(addresses from 1 to 200);
- videointercoms in the same apartment; it allows to
intercommunicate with the equipment of other rooms in the same
apartment (room number from 0 to 7);
- door stations (not necessary in the case of a single door station);
it allows the videointercom to connect them selectively, monitor the
entrance and eventually release the door lock (addresses from 231
to 250);
- actuators for supplementary services (supplementary door lock
release, switch-ON of stair's light, etc.); it allows the videointercom
to enable directly the actuators (addresses from 211 to 220).
Warning: the addresses stored in the videointercom must be the
same of those programmed in the devices to enable.
2.
15
(MT13 - En 2015)
2
". This operation will
". A floor call makes