Chapter 4 Commands; Command Listing - YOKOGAWA PZ4000 User Manual

Chapter 4 Commands

4.1 Command Listing

Command
ABORt Group
:ABORt
ACQuire Group
:ACQuire?
:ACQuire:DIVision
:ACQuire:RLENgth
:ACQuire:TBASe
CHANnel Group
:CHANnel<x>?
:CHANnel<x>:CURRent?
:CHANnel<x>:CURRent:RANGe
:CHANnel<x>:CURRent:SRATio
:CHANnel<x>:CURRent:TERMinal
:CHANnel<x>:DISPlay
:CHANnel<x>:LABel
:CHANnel<x>:POSition
:CHANnel<x>:SPEed?
:CHANnel<x>:SPEed:FRANge
:CHANnel<x>:SPEed:RANGe
:CHANnel<x>:SPEed:TYPE
:CHANnel<x>:TORQue?
:CHANnel<x>:TORQue:RANGe
:CHANnel<x>:TYPE?
:CHANnel<x>:VOLTage?
:CHANnel<x>:VOLTage:RANGe
:CHANnel<x>:VZoom
COMMunicate Group
:COMMunicate?
:COMMunicate:HEADer
:COMMunicate:LOCKout
:COMMunicate:OPSE
:COMMunicate:OPSR?
:COMMunicate:OVERlap
:COMMunicate:REMote
:COMMunicate:STATus?
:COMMunicate:VERBose
:COMMunicate:WAIT
:COMMunicate:WAIT?
CURSor Group
:CURSor?
:CURSor:HORizontal?
:CURSor:HORizontal:DY?
:CURSor:HORizontal:POSition<x>
IM 253710-11E
Function
Aborts data acquisition.
Queries all settings related to data acquisition.
Sets whether or not to divide the record length or queries the current setting.
Sets the record length or queries the current setting.
Sets the sampling block or queries the current setting.
Queries all settings related to the vertical axis of each channel.
Queries all settings related to the current input channel.
Sets the current range of the current input channel or queries the current setting.
Sets the current sensor's scaling constant of the current input channel or queries the
current setting.
Sets the current measurement terminal of the current input channel or queries the current
setting.
Turns ON/OFF the waveform display of each channel or queries the current setting.
Sets the waveform label of each channel or queries the current setting.
Sets the vertical position (the GND position) of each channel or queries the current setting. 4-14
Queries all settings related to the revolution sensor signal input channel.
Sets the frequency range of the revolution sensor signal input channel (pulse input) or
queries the current setting.
Sets the input range of the revolution sensor signal input channel or queries the current
setting.
Sets the input type of the revolution sensor signal input channel or queries the current
setting.
Queries all settings related to the torque meter signal input channel.
Sets the input range of the torque meter signal input channel or queries the current setting. 4-15
Queries the input type of each channel.
Queries all settings related to the voltage input channel.
Sets the voltage range of the voltage input channel or queries the current setting.
Sets the vertical zoom factor or queries the current setting.
Queries all settings related to communications.
Sets whether or not to attach headers to response data or queries the current setting.
Sets/releases local lockout.
Sets the overlap commands for
Queries the operation pending status register.
Sets the commands to permit overlap operation or queries the current setting.
Switches between remote and local.
Queries the line-specific status.
Sets whether to use the full or abbreviated form for response data or queries the current
setting.
Waits for an extended event to occur.
Generates a response when one of the specified extended events occurs.
Queries all settings related to cursor measurements.
Queries all settings related to the H cursor.
Queries the Y-axis value between the H cursors.
Sets the H cursor position or queries the current setting.
*OPC , *OPC? , and *WAI or queries the current setting.
4.1 Command Listing
Page
4-11
4-11
4-11
4-11
4-11
4-13
4-13
4-13
4-13
4-13
4-13
4-14
4-14
4-14
4-14
4-15
4-15
4-15
4-15
4-15
4-15
4-16
4-16
4-16
4-17
4-17
4-17
4-17
4-17
4-17
4-17
4-17
4-19
4-19
4-19
4-19
4-1
4