YOKOGAWA PZ4000 User Manual page 39

4.1 Command Listing
Command
:TRIGger:WINDow:CENTer
:TRIGger:WINDow:CONDition
:TRIGger:WINDow:WIDTh
WAVeform Group
:WAVeform?
:WAVeform:BYTeorder
:WAVeform:END
:WAVeform:FORMat
:WAVeform:LENGth?
:WAVeform:RANGe?
:WAVeform:SEND?
:WAVeform:SRATe?
:WAVeform:STARt
:WAVeform:TDATe?
:WAVeform:TRACe
:WAVeform:TRIGger?
:WAVeform:ZCRoss?
ZOOM Group
:ZOOM?
:ZOOM:ALLOcation?
:ZOOM:ALLOcation:{CHANnel<x>|MATH<x>}
:ZOOM:FORMat
:ZOOM:MAG<x>
:ZOOM[:MODE]
:ZOOM:POSition<x>
Common Command Group
*CAL?(CALibrate)
*CLS(CLear Status)
*ESE(standard Event Status Enable register)
*ESR?(standard Event Status Register)
*IDN?(IDeNtify)
*OPC(OPeration Complete)
*OPC?(OPeration Complete)
*OPT?(OPTion)
*PSC(Power-on Status Clear)
*RST(ReSeT)
*SRE(Service Request Enable register)
*STB?(STatus Byte)
*TRG(TRiGger)
*TST(TeST)
*WAI(WAIt)
4-10
Function
Sets the center level for the window trigger or queries the current setting.
Sets the trigger condition for the window trigger or queries the current setting.
Sets the window width for the window trigger or queries the current setting.
Queries all settings related to the waveform data.
Sets the byte order of the waveform data or queries the current setting.
Sets the end point of the output of the waveform data or queries the current setting.
Sets the format of the waveform data or queries the current setting?
Queries the total number of data points of the waveform.
Queries the range value that is used to convert the waveform to physical data.
Queries the waveform data.
Queries the sampling rate of the acquired data.
Sets the start point of the output of the waveform data or queries the current setting.
Queries the string containing the trigger date and time when the waveform was acquired. 4-82
Sets the waveform or queries the current setting.
Queries the trigger position of the acquired data.
Queries zero crossing data of all channels.
Queries all settings related to the zooming of the waveform.
Queries all settings related to the zoomed waveform.
Sets whether or not to select the waveform to be zoomed or queries the current setting.
Sets the display format of the zoomed waveform or queries the current setting.
Sets the zoom factor or queries the current setting.
Sets the the display mode of the zoomed waveform or queries the current setting.
Sets the position of the zoom box or queries the current setting.
Performs calibration (zero level compensation) and queries the result.
Clears the standard event register, extended event register, and error queue.
Sets the standard event enable register or queries the current setting.
Queries the standard event register and clears the register.
Queries the instrument model.
After the completion of the specified overlap command, sets the OPC event.
Creates a response, after the completion of the specified overlap command.
Queries installed options.
Sets whether or not to clear each register on power up or queries the current setting.
Initializes the command group settings.
Sets the service request enable register or queries the current setting.
Queries the status byte register.
Executes single start.
Executes the self-test and queries the result.
Waits until the execution of the specified overlap command completes before executing
the commands that are specified after this command.
Page
4-79
4-79
4-79
4-80
4-80
4-80
4-81
4-81
4-81
4-81
4-81
4-82
4-82
4-82
4-82
4-83
4-83
4-84
4-84
4-84
4-84
4-84
4-85
4-85
4-85
4-86
4-86
4-86
4-86
4-86
4-86
4-86
4-87
4-87
4-87
4-87
4-87
IM 253710-11E