YOKOGAWA PZ4000 User Manual page 74

[:INPut]:MOTor:PM:UNIT
Function Sets the unit to add to the motor output
computation result or queries the current
setting.
Syntax [:INPut]:MOTor:PM:UNIT {<string>}
[:INPut]:MOTor:PM:UNIT?
<string> = 8 characters or less
Example :INPUT:MOTOR:PM:UNIT "W"
:INPUT:MOTOR:PM:UNIT?→:INPUT:MOTOR:PM:
UNIT "W"
Description • Characters and symbols other than the ones
displayed on the keyboard on the screen
cannot be used.
• This command never affects the computation
result.
• If the 253771 motor module is not installed,
an error will occur.
[:INPut]:MOTor:POLE
Function Sets the motor's number of poles for the motor
module or queries the current setting.
Syntax [:INPut]:MOTor:POLE {<NRf>}
[:INPut]:MOTor:POLE?
<NRf> = 1 to 99
Example :INPUT:MOTOR:POLE 2
:INPUT:MOTOR:POLE?→:INPUT:MOTOR:POLE 2
Description If the 253771 motor module is not installed, an
error will occur.
[:INPut]:MOTor:SPEed?
Function Queries all settings related to the revolution
sensor signal input for the motor module.
Syntax [:INPut]:MOTor:SPEed?
Example :INPUT:MOTOR:SPEED?→:INPUT:MOTOR:SPEED:
RANGE 50.0E+00;TYPE ANALOG;
FRANGE 200.00E+03;PULSE 60;
SCALING 1.0000;UNIT "Nm"
Description If the 253771 motor module is not installed, an
error will occur.
IM 253710-11E
[:INPut]:MOTor:SPEed:FRANge
Function Sets the frequency range of the revolution
sensor signal input (pulse input) for the motor
module or queries the current setting.
Syntax [:INPut]:MOTor:SPEed:FRANge {<frequency>
|AUTO}
[:INPut]:MOTor:SPEed:FRANge?
<Frequency> = 40(Hz): 1 to 40 Hz
= 800(Hz): 16 to 800 Hz
= 8k(Hz): 250 to 8 kHz
= 200k(Hz): 2 k to 200 kHz
AUTO = Auto range
Example :INPUT:MOTOR:SPEED:FRANGE 200KHZ
:INPUT:MOTOR:SPEED:FRANGE?→:INPUT:
MOTOR:SPEED:FRANGE 200.00E+03
Description • Set the <Frequency> to the maximum value
within the frequency range.
• This command is valid when the input format
of the revolution sensor signal
( [:INPut]:MOTor:SPEed:TYPE
" PULSe (pulse input).
• If the 253771 motor module is not installed,
an error will occur.
• The "
:CHANnel7:SPEed:FRANGe
can be used to make the same settings and
inquiries.
[:INPut]:MOTor:SPEed:PULSe
Function Sets the pulse count of the revolution sensor
signal input (pulse input) for the motor module
or queries the current setting.
Syntax [:INPut]:MOTor:SPEed:PULSe {<NRf>}
[:INPut]:MOTor:SPEed:PULSe?
<NRf> = 1 to 9999
Example :INPUT:MOTOR:SPEED:PULSE 60
:INPUT:MOTOR:SPEED:PULSE?→:INPUT:MOTOR:
SPEED:PULSE 60
Description • This command is valid when the input format
of the revolution sensor signal
( [:INPut]:MOTor:SPEed:TYPE
" PULSe (pulse input).
• If the 253771 motor module is not installed,
an error will occur.
4.11 INPut Group
4
) is set to
"
" command
) is set to
"
4-45