Appendix A - System Error Message; Error Messages - DFI KS070-BT User Manual

Appendix A - System Error Message

When the BIOS encounters an error that requires the user to correct something, either a beep
code will sound or a message will be displayed in a box in the middle of the screen and the
message, PRESS F1 TO CONTINUE, CTRL-ALT-ESC or DEL TO ENTER SETUP, will be shown in
the information box at the bottom. Enter Setup to correct the error.

Error Messages

One or more of the following messages may be displayed if the BIOS detects an error during
the POST. This list indicates the error messages for all Awards BIOSes:
CMOS BATTERY HAS FAILED
The CMOS battery is no longer functional. It should be replaced.
Important:
Danger of explosion if battery incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries accord-
ing to the battery manufacturer's instructions.
CMOS CHECKSUM ERROR
Checksum of CMOS is incorrect. This can indicate that CMOS has become corrupt. This error
may have been caused by a weak battery. Check the battery and replace if necessary.
DISPLAY SWITCH IS SET INCORRECTLY
The display switch on the motherboard can be set to either monochrome or color. This indi-
cates the switch is set to a different setting than indicated in Setup. Determine which setting
is correct, either turn off the system and change the jumper or enter Setup and change the
VIDEO selection.
Appendix A System Error Message
Appendix A
Standard Status Codes
(for BayTrail BT Series model with AMI Code base BIOS , INSIDE BIOS 不適用)
PEI Status Codes
PEI Phase - Progress Codes
0x11 Pre-memory CPU initialization is started
(for BayTrail BT Series model with AMI Code base BIOS , INSIDE BIOS 不適用)
0x15 Pre-memory North Bridge initialization is started
PEI Phase - Progress Codes
0x19 Pre-memory South Bridge initialization is started
0x11 Pre-memory CPU initialization is started
0x2A OEM pre-memory initialization codes
0x15 Pre-memory North Bridge initialization is started
0x2B Memory initialization. Serial Presence Detect (SPD) data reading
0x19 Pre-memory South Bridge initialization is started
0x2C Memory initialization. Memory presence detection
0x2A OEM pre-memory initialization codes
0x2D Memory initialization. Programming memory timing information
0x2B Memory initialization. Serial Presence Detect (SPD) data reading
0x2E Memory initialization. Configuring memory
0x2C Memory initialization. Memory presence detection
0x2F Memory initialization (other).
0x2D Memory initialization. Programming memory timing information
PEI Error Codes
0x2E Memory initialization. Configuring memory
0x50 Memory initialization error. Invalid memory type or incompatible memory speed
0x2F Memory initialization (other).
PEI Error Codes
0x51 Memory initialization error. SPD reading has failed
PEI Error Codes
0x52 Memory initialization error. Invalid memory size or memory modules do not match.
0x50 Memory initialization error. Invalid memory type or incompatible memory speed
0x53 Memory initialization error. No usable memory detected
0x51 Memory initialization error. SPD reading has failed
DXE Phase
0x52 Memory initialization error. Invalid memory size or memory modules do not match.
0x92 PCI Bus initialization is started
0x53 Memory initialization error. No usable memory detected
0x93 PCI Bus Hot Plug Controller Initialization
DXE Phase
0x94 PCI Bus Enumeration
0x92 PCI Bus initialization is started
0x95 PCI Bus Request Resources
0x93 PCI Bus Hot Plug Controller Initialization
0x96 PCI Bus Assign Resources
0x94 PCI Bus Enumeration
0x99 Super IO Initialization
0x95 PCI Bus Request Resources
0x9A USB initialization is started
0x96 PCI Bus Assign Resources
0x9B USB Reset
0x99 Super IO Initialization
0x9C USB Detect
0x9A USB initialization is started
0x9D USB Enable
0x9B USB Reset
0xA0 IDE initialization is started
0x9C USB Detect
0xA1 IDE Reset
0x9D USB Enable
0xA2 IDE Detect
0xA0 IDE initialization is started
0xA3 IDE Enable
0xA1 IDE Reset
0xAE Legacy Boot event
0xA2 IDE Detect
0xB4 USB hot plug
0xA3 IDE Enable
0xB6 Clean-up of NVRAM
0xAE Legacy Boot event
0xB7 Configuration Reset (reset of NVRAM settings)
55
0xB4 USB hot plug
DXE Error Codes
0xB6 Clean-up of NVRAM
0xD6 No Console Output Devices are found
www.dfi.com