Start-Up Procedure Of The System - Mitsubishi Electric FX3U-128ASL-M User Manual

FX -128ASL-M User's Manual
3U
3.7

Start-up procedure of the system

Start up the AnyWireASLINK system using the following procedure:
Attach the 128ASL-M, slave modules and others to the control panel or machine. Attach the 128ASL-M, slave modules and others to the control panel or machine.
Wire the 128ASL-M, slave modules and power supply, and connect Wire the 128ASL-M, slave modules and power supply, and connect
the terminating unit at the end farthest from the 128ASL-M. the terminating unit at the end farthest from the 128ASL-M.
Set the number of transmission points of the 128ASL-M using the rotary switches Set the number of transmission points of the 128ASL-M using the rotary switches
in accordance with the number of input/output points of slave modules. in accordance with the number of input/output points of slave modules.
Slave module address setting (For a slave module equipped with DIP switch) Slave module address setting (For a slave module equipped with DIP switch)
(For a slave module equipped with DIP switch, the address can be set even (For a slave module equipped with DIP switch, the address can be set even
before the power is turned ON. However, for a slave module that relies on the before the power is turned ON. However, for a slave module that relies on the
address writer, the address can be set only after the power is turned ON.) address writer, the address can be set only after the power is turned ON.)
Check before turning ON the power Check before turning ON the power
- Check the attachment status of the 128ASL-M, slave modules and power supply. - Check the attachment status of the 128ASL-M, slave modules and power supply.
- Check whether the RUN/STOP switch of the main unit is set to "STOP". - Check whether the RUN/STOP switch of the main unit is set to "STOP".
- Check whether the total length of the AnyWireASLINK system meets the specification. - Check whether the total length of the AnyWireASLINK system meets the specification.
- Check whether the power supply of the AnyWireASLINK system meets the specification. - Check whether the power supply of the AnyWireASLINK system meets the specification.
Turn ON the power of the external power supply for the AnyWireASLINK system and Turn ON the power of the external power supply for the AnyWireASLINK system and
Slave module address setting (For a slave module that relies on the address writer) Slave module address setting (For a slave module that relies on the address writer)
(For a slave module equipped with DIP switch, the address can be set even (For a slave module equipped with DIP switch, the address can be set even
before the power is turned ON. However, for a slave module that relies on the address before the power is turned ON. However, for a slave module that relies on the address
writer, the address can be set only after the power is turned ON.) writer, the address can be set only after the power is turned ON.)
Turn OFF the power, and turn it ON again so that the address setting for the slave Turn OFF the power, and turn it ON again so that the address setting for the slave
module is reflected. module is reflected.
Checking the operation based on LEDs Checking the operation based on LEDs
Check whether the LEDs on the 128ASL-M are as follows: Check whether the LEDs on the 128ASL-M are as follows:
• POWER LED : ON • POWER LED : ON
• LINK LED • LINK LED
Check whether the LEDs in the slave module are as follows: Check whether the LEDs in the slave module are as follows:
• LINK LED • LINK LED
Write the control program to the main unit. Write the control program to the main unit.
Start Start
the power of the main unit in this order. the power of the main unit in this order.
: Flicker : Flicker
: Flicker : Flicker
Perform automatic address detection. Perform automatic address detection.
Operate the system. Operate the system.
End End
3 System Configuration
3.7 Start-up procedure of the system
Refer to Chapter 4.
Refer to Chapter 5.
Refer to Section 3.5.
Refer to product guide
for the slave module
(manufactured by Anywire
Corporation).
Refer to the Hardware Edition
manual of each main unit.
Refer to Subsection 2.4.4,
Chapter 4 and Section 5.5.
Refer to Section 5.6.
Refer to product guide
for the slave module
(manufactured by Anywire
Corporation).
Refer to Section 1.3 and
Section 9.1.
Refer to product guide
for the slave module
(manufactured by Anywire
Corporation).
Refer to Subsection 6.2.3.
Refer to Chapter 8.
1
2
3
4
5
6
7
8
9
A
29