Toyota 4A-FE Repair Manual page 222

A-4
SERVICE SPECIFICATIONS - Engine Mechanical (4A-FE)
Specifications (Cont'd)
Camshaft Thrust clearance STD Intake 0 .030 - 0.085 mm
0.0012 - 0.0033 in.
Exhaust 0 .035 - 0.090 mm 0.0014 - 0.0035 in.
Limit 0 .11 mm 0 .0043 in.
Journal oil clearance STD 0 .035 - 0.072 mm 0.0014 - 0.0028 in.
Limit 0.10 mm
0.0039 in.
Journal diameter STD
Exhaust No. 1 24.949 - 24.965 mm 0.9822 - 0.9829 in.
Others 22 .949 - 22.965 mm 0.9035 - 0.9041 in .
Circle runout Limit 0.04 mm 0.0016 in.
Cam lobe height STD Intake 35 .21 - 35.31 mm 1 .3862 - 1 .3902 in.
Exhaust 34.91 - 35.01 mm
1.3744 - 1.3783 in.
Limit Intake 34.81 mm 1.3705 in .
Exhaust 34 .51 mm 1.3587 in.
Camshaft gear spring end free distance 17 .1 - 1 7 .5 mm 0.6732 - 0 .6890 in.
Camshaft gear backlash
STD
0.020 - 0.200 mm 0 .0008 - 0.0079 in.
Limit 0.30 mm 0.0188 in.
Cylinder block Cylinder head surface warpage Limit 0.05 mm 0.0020 in.
Cylinder bore STD
Mark "1" 81 .00 - 81 .01
mm
3.1890 - 3.1894 in.
Mark "2" 81 .01 - 81.02 mm 3. 1 8 9 4 - 3. 1 8 9 8 in.
Mark "3" 81 .02 - 81.03 mm 3.1898 - 3.1902 in.
On standard sized piston Limit 81 .23 mm 3 .1980 in.
On O/S 0 .50 sized piston Limit 81 .73mm 3.21 77 in.
Cylinder bore wear
Limit
0.2 mm
0.008 in.
Difference of bore between cylinder 0.05 mm 0.0020 in.
Taper and out-of-round Limit 0 .02 mm 0 .0008 in .
Piston and Piston diameter STD Mark "1" 80.93 - 80.94 mm 3.1862 - 3.1886 in.
piston ring
Mark "2"
80.94 - 80 .95 mm
3.1866 - 3.1870 in.
Mark "3" 80.95 - 80.96 mm
3.1870 - 3.1874 in.
0/S 0.50
81.43 - 81.46 mm
3 .2059 - 3.2071 in.
Piston to cylinder clearance 0.06 - 0.08 mm 0.0024 - 0.0031 in.
Piston ring end gap No. 1 STD 0.25 - 0.45 mm 0.0098 - 0.01 77 in.
!
Limit 1.05 mm 0 .0413 in.
No. 2 STD 0.15 - 0.40 mm 0 .0059 - 0.0157 in.
Limit 1.00 mm 0.0394 in.
Oil STD 0.10 - 0.70 mm 0.0039 - 0.0276 in.
Limit 1.30 mm 0 .0512 in.
Ring to ring groove clearance No. 1 0.04 - 0 .08 mm 0.0016 - 0.0031 in.
No. 2 0.03 - 0 .07 mm 0.0012 - 0.0028 in.
Piston pin installing temperature 20°c
68°F
Connecting rod Thrust clearance STD 0.15 - 0 .25 mm 0.0059 - 0.0098 in.
Limit 0.30 mm 0.0118 in.
Connecting rod bearing center wall
thickness
STD No. 1 1 .486 - 1 .490 mm 0.0585 - 0.0587 in.
No . 2 1.490 - 1.494 mm 0.0587 - 0.0588 in.
No. 3 1.494 - 1.498 mm 0 .0588 - 0 .0590 in.
U/S 0.25
1.607 - 1.613 mm
0 .0633 - 0 .0635 in .