Download Print this page

Fujitsu ETERNUS DX Configuration Manual

Fibre channel for oracle solaris driver settings for non-fujitsu fibre channel cards
Hide thumbs

Advertisement

Quick Links

P3AM-6312-18ENZ0
FUJITSU Storage
ETERNUS DX, ETERNUS AF
Configuration Guide -Server Connection-
(Fibre Channel) for Oracle Solaris
Driver Settings for Non-Fujitsu Fibre Channel Cards

Advertisement

loading

  Related Manuals for Fujitsu ETERNUS DX

  Summary of Contents for Fujitsu ETERNUS DX

  • Page 1 P3AM-6312-18ENZ0 FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Driver Settings for Non-Fujitsu Fibre Channel Cards...
  • Page 2 This page is intentionally left blank.
  • Page 3 Preface This manual briefly explains the operations that need to be performed by the user in order to connect an ETERNUS DX/AF to a server running Solaris OS and using non-Fujitsu Fibre Channel cards via a Fibre Channel interface. This manual is used when performing the setup procedure described in "Installing Drivers and Setting Up the Server"...
  • Page 4: Table Of Contents

    2.5.1 For Driver Versions V6.30g and Later ........................41 2.5.2 For Driver Versions Before V6.30g........................47 Chapter 3 Setup Procedure for QLogic Fibre Channel Cards FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 5 A.1 WWN Instance Management Table for the Server ................ 82 A.2 WWN Instance Management Table for Storage System ..............82 A.3 Target Binding Table ........................83 FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 6: Chapter 1 Operations When Using Oracle Fibre Channel Cards

    "1.5 Required Driver Parameters" (page 20) • • Checking the Oracle driver notes "Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris" FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 7: Installing The Fibre Channel Card Driver

    Driver installation is not necessary because the OS-bundled driver is used. Solaris 9 OS or Solaris 8 OS • Download and install the appropriate driver from the Oracle web-site. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 8: Setting Up The Server

    Setting Up the Server Setting Up the Server The server setup will vary according to how the ETERNUS DX/AF storage systems and server are to be connec- ted. There are two possible connection topologies: direct connection and switch connection. Edit the server's configuration file to match the chosen topology. Configuration files may also differ depend- ing on which Fibre Channel card drivers are to be used.
  • Page 9: Oracle Driver For Qlogic Oem Fibre Channel Cards

    Fibre Channel card and enter them in the "WWN instance management table for the server" (provided in "Appendix A Various Management Table Templates" (page 82)). FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 10 SUNW,qlc-pciex1077,2432 QLE2460 Physical slot name Controller number Instance name Physical path name PCIE 0 qlc0 /pci@9,600000/SUNW,qlc@1 PCIE 1 qlc1 /pci@9,600000/SUNW,qlc@2 FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 11 When Type Busy Phys_Id c4 connected unconfigured unknown unavailable fc-fabric n /devices/pci@9,600000/SUNW,qlc@1/fp@0,0:fc c5 connected unconfigured unknown unavailable fc-fabric n /devices/pci@9,600000/SUNW,qlc@2/fp@0,0:fc FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 12 • The number of simultaneous command executions per CA port for the ETERNUS DX/AF is limited to 1024. This value is used by multiple servers that share the CA port. A maximum of 1024 com- mands can be executed per CA port.
  • Page 13: Oracle Driver For Emulex Oem Fibre Channel Cards

    "WWN instance management table for the server" (provided in "Appendix A Various Man- agement Table Templates" (page 82)). FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 14 /pci@9,600000/SUNW,emlxs@1 SUNW,emlxs-pci10df,fd+LP11002-M4 Physical slot name Controller number Physical path name Instance name PCIE 0 emlxs0 /pci@9,600000/SUNW,emlxs@1 PCIE 1 emlxs1 /pci@9,600000/SUNW,emlxs@1,1 FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 15 When Type Busy Phys_Id c4 connected unconfigured unknown unavailable fc-fabric n /devices/pci@9,600000/SUNW,emlxs@1/fp@0,0:fc c5 connected unconfigured unknown unavailable fc-fabric n /devices/pci@9,600000/SUNW,emlxs@1,1/fp@0,0:fC FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 16 • load and the peak operating times. The number of simultaneous command executions per CA port for the ETERNUS DX/AF is limited • to 1024. This value is used by multiple servers that share the CA port. A maximum of 1024 com- mands can be executed per CA port.
  • Page 17: Setting Up The Server To Recognize The Logical Units

    DX/AF storage systems to server connection topology. There are two possible connection topologies: direct connection and switch connection. 1.4.1 For Direct Connection Confirm that the logical units have been correctly recognized by servers. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 18 The underlined portion indicates that the ETERNUS DX8100/DX8400/DX8700 target ID=16, lun=0 and 1 are connected to physical path /pci@9,600000/SUNW,qlc@1, and that c4t16d0 and c4t16d1 are as- signed to each of these LUNs. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 19: For Switch Connection

    Example: # cfgadm -c configure c4::21ff00e000a8ffaf # cfgadm -c configure c5::25ff00e000a8ffaf Use the following command to confirm that the paths to the ETERNUS DX/AF are now usable. "Occupant" status changes from "unconfigured" to "configured". # cfgadm -al # cfgadm -al...
  • Page 20: Required Driver Parameters

    If the "/etc/driver/drv/emlxs.conf” file exists, do not copy over the file but instead edit the existing "emlxs.conf" file. Solaris 10 OS • Edit the "/kernel/drv/emlxs.conf" file. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 21 "/pci@9,600000" 3 "pcisch" "/pci@9,600000/fibre-channel@1" 0 "emlxs" "/pci@9,600000/fibre-channel@1/fp@0,0" 0 "fp" The underlined portion indicates the instance number and the instance name. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 22: Emlxs.conf Parameter List

    CA transfer rate card transfer rate 16Gbit/s 8Gbit/s 4Gbit/s 2Gbit/s 8Gbit/s 4Gbit/s 16Gbit/s — — — 8Gbit/s 4Gbit/s 2Gbit/s — FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 23: Emlxs.conf Parameter Example

    Max:1 Default:1 network-on=1; # +++ Fibre Channel specific parameters +++ # topology: link topology for initializing the Fibre Channel connection. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 24 # 2 = Full support. Hold active I/O's for all devices at link down. # Range: Min:0 Max:2 Default:1 adisc-support=1; # pm-support: Enable/Disable power management support in the driver. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 25 # This parameter is only used by the driver on i386 platforms. # The driver does not limit transfer size on SPARC platforms. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED...
  • Page 26 ---------------------------------------- Small 131072 - 339968 Medium 339969 - 688128 Large 688129 - 1388544 # Range: Min:131072 Max:1388544 Default:339968 max-xfer-size=339968; FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 27: Chapter 2 Setup Procedure For Emulex Fibre Channel Cards

    Set the driver parameters by editing the configuration file. "2.3 Setting Up the Server" (page 31) • "2.5 Required Driver Parameters" (page 40) • FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 28: Installing The Fibre Channel Card Driver

    For details of installation, refer to the FCA Utility Manual in the following Emulex web-site: http://www.emulex.com Check that Emulex lpfc driver is not installed. If installed, uninstall it using "pkgrm" command. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 29 Manual". Perform the following procedure to unbind the Emulex driver. Move to the Emulex FCA utility directory. #cd /opt/EMLXemlxu/bin FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 30: Solaris 10 Os, Solaris 9 Os, Or Solaris 8 Os

    2.2.2 Solaris 10 OS, Solaris 9 OS, or Solaris 8 OS Download and install the driver from the Emulex web-site. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 31: Setting Up The Server

    Setting Up the Server Setting Up the Server The server setup will vary according to how the ETERNUS DX/AF storage systems and server are to be connec- ted. Edit the server's configuration file to match the chosen topology. Configuration files may also differ depend- ing on which Fibre Channel cards are to be used.
  • Page 32 Nov 17 10:26:24 t5220.i14y-ux.com pxb_plx: [ID 370704 kern.info] PCI-device: lpfc@0,1, lpfc1 Nov 17 10:26:24 t5220.i14y-ux.com genunix: [ID 936769 kern.info] lpfc1 is /pci@0/pci@0/pci@8/pci@0/pci@1/lpfc@0,1 Instance name FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 33: Creating A Wwn Instance Management Table For Storage System

    (Example) When there are two ports on the ETERNUS DX/AF storage systems: Channel Adapter Alias name T_ID CM0CA0Port0 202000e000cb0001 DX400_CM0CA0P0 CM1CA0Port0 203000e000cb0001 DX400_CM1CA0P0 FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 34: Creating A Target Binding Table

    Fibre Channel Switch B CA0 Port0 CA0 Port1 CA0 Port0 CA0 Port1 ETERNUS DX/AF Physical slots on Server#0 and CAs on the ETERNUS DX/AF storage systems are connected in the follow- ing paths. • Server#0 SLOT0 - CM0CA0 • Server#0 SLOT1 - CM1CA0...
  • Page 35: Setting The Configuration File

    Check the target binding values before rebooting the server. If the server boots with a setting error, it may recognize a different storage system from that set in the system configuration, without generating a con- nection error. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 36: Setting Up The Server To Recognize The Logical Units

    Make the server recognize the ETERNUS DX/AF logical units using the sd driver. First, confirm that the logical unit settings on the ETERNUS DX/AF storage systems are correct. Next, add the descriptions of the logical units in the sd driver's configuration file (sd.conf) to register the units.
  • Page 37 • Add the line to the "/kernel/drv/sd.conf" file. Do not delete the lun=0 description for the system disk target ID. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 38 Reconfigure and reboot the server to get it to recognize the listed logical units. Execute the following command. # touch /reconfigure # /usr/sbin/shutdown -y -g0 -i6 FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 39 3. c5t16d0 <FUJITSU-ETERNUS_DX400 cyl 1022 alt 2 hd 64 sec 256> /pci@9,600000/lpfc@2/sd@10,0 4. c5t16d1 <FUJITSU-ETERNUS_DX400 cyl 1022 alt 2 hd 64 sec 256> /pci@9,600000/lpfc@2/sd@10,1 Specify disk (enter its number): FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 40: Required Driver Parameters

    Check the "WWN instance management table for the server" for the actual "X" instance numbers to use in the lpfcX. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 41: For Driver Versions V6.30G And Later

    — — num-iocbs — — num-bufs — — lpfcX-topology — ip-class — — fcp-class — — use-adisc — — FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 42 Direct connection Fibre Channel (Fibre Channel switch transfer rate) card transfer rate 8Gbit/s 4Gbit/s 2Gbit/s FC-CA(4G) FC-CA(8G) 8Gbit/s 4Gbit/s 2Gbit/s FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 43 # WWPN must be 16 digit BCD with leading 0s. # DID must be 6 digit BCD with leading 0s. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 44 # and the actual fail back. A value of zero implies no delay whatsoever. # Cautions: This value is in seconds. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 45 # Set a preferred ALPA for the adapter, only valid if topology is loop. # lpfc0-assign-alpa=2; Request ALPA 2 for lpfc0 FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 46 2 = enable multiple message MSI 3 = auto select (default) msi-mode=3; # Setup FCP device to target driver associations target-disk="sd"; target-tape="st"; target-tapechanger="sgen"; FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 47: For Driver Versions Before V6.30G

    For the ETERNUS DX400 S2 series and the ETERNUS DX8000 S2 series: Not re- quired no-device-delay — — network-on — — FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 48 Switch connection Fibre Channel card trans- Direct connec- (Fibre Channel switch transfer rate) fer rate tion 8Gbit/s 4Gbit/s 2Gbit/s 1Gbit/s 4Gbit/s FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 49 Switch connection Fibre Channel card trans- Direct connec- (Fibre Channel switch transfer rate) fer rate tion 8Gbit/s 4Gbit/s 2Gbit/s 1Gbit/s 2Gbit/s FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 50 # NOTE: Target ids, with all luns supported, must also be in sd.conf. # Here are some examples: WWNN SCSI ID FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 51 # critical Solaris kernel resources. In this case, you may see a fatal # message such as PANIC: Timeout table overflow FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 52 Confirm that the value is "3". If it is not, change it to "3". # ip-class: FC class (2 or 3) to use for the IP protocol. ip-class=3; FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 53 2 = enable fdmi and "host name" port attribute fdmi-on=0; # Used only by i386 FCP (SCSI) # flow_control="duplx" queue="qfifo" disk="scdk" tape="sctp"; FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 54: Chapter 3 Setup Procedure For Qlogic Fibre Channel Cards

    Set the driver parameters by editing the configuration file. "3.3 Setting Up the Server" (page 55) • "3.5 Required Driver Parameters" (page 66) • FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 55: Installing The Fibre Channel Card Driver

    Setting Up the Server The server setup will vary according to how the ETERNUS DX/AF storage systems and server are to be connec- ted. Edit the server's configuration file to match the chosen topology. Configuration files may also differ de- pending on which Fibre Channel cards are to be used.
  • Page 56: Creating A Wwn Instance Management Table For The Server

    " 0 "qla2300" "/pci@b,2000/QLGC,qla@2, 1" 1 "qla2300" The underlined portion "/pci@b,2000/QLGC,qla@2" indicates the physical path name, and "1" indicates the instance number. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 57 9: Boot Device Settings 10: Driver Settings 11: HBA Utilities 12: Flash Beacon 13: Diagnostics 14: Statistics 15: Help 16: Quit FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 58 2: Port 2 (OS 1): WWPN: 21-01-00-E0-8B-B1-D9-4F Online 3: All HBAs 4: Return to Previous Menu Note: 0 to return to Main Menu Enter Selection: 3 FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 59 2: Port 2 (OS 1): WWPN: 21-01-00-E0-8B-B1-D9-4F Online 3: All HBAs 4: Return to Previous Menu Note: 0 to return to Main Menu Enter Selection: 4 FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 60: Creating A Wwn Instance Management Table For Storage System

    CA name in the ETERNUS DX/AF storage systems • The WWN for each CA in the ETERNUS DX/AF (check using ETERNUS Web GUI or ETERNUSmgr) FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris...
  • Page 61: Creating A Target Binding Table

    Slot0 Slot1 Fibre Channel Switch A Fibre Channel Switch B CA0 Port0 CA0 Port1 CA0 Port0 CA0 Port1 ETERNUS DX/AF FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 62: Setting The Configuration File

    Chapter 3 Setup Procedure for QLogic Fibre Channel Cards Setting Up the Server Physical slots on Server#0 and CAs on the ETERNUS DX/AF storage systems are connected in the follow- ing paths. Server#0 SLOT0 - CM0CA0 • Server#0 SLOT1 - CM1CA0 •...
  • Page 63: Setting Up The Server To Recognize The Logical Units

    Make the server recognize the ETERNUS DX/AF logical units using the sd driver. First, confirm that the logical unit settings on the ETERNUS DX/AF storage systems are correct. Next, check that Fibre Channel card IDs are described in the sd driver's configuration file (sd.conf).
  • Page 64 # Enabling Target 7 allows the use of 8 disks on those controllers. name="sd" parent="mpt" target=7 lun=0; name="sd" parent="qla2300" target=2048; Check the underlined portion. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 65 Reconfigure and reboot the server to get it to recognize the listed logical units. Execute the following command. The ETERNUS DX/AF can be reconfigured by creating the "/reconfigure" file and rebooting the server. # touch /reconfigure # /usr/sbin/shutdown -y -g0 -i6 After the server has booted up, log in as a superuser, and use the "format"...
  • Page 66: Required Driver Parameters

    — hbaX-reset-delay — hbaX-port-down-retry-count — hbaX-port-down-retry-delay — hbaX-maximum-luns-per-target — hbaX-connection-options 0 for direct connection • • 1 for switch connection FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 67 *2: Recommended value = 512 ¸ (number of Fibre Channel ports that are connected to a single CA port) (Round the result down) Use the value of "8" if the actual result is lower. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 68 32Gbit/s 16Gbit/s 8Gbit/s 4Gbit/s rate 32Gbit/s — — — 16Gbit/s — 8Gbit/s 4Gbit/s — — 2Gbit/s — — — — FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 69 Please refer to the FAQ section for which default SCSI target IDs are assigned to fabric devices. # *********************** # CAUTION CAUTION CAUTION # *********************** FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 70 # Number of times to retry a port that is not responding. Range: 0 - 255 FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 71 # Use target/lun VPD data for failover configuration support. 0 = disabled, 1 = enable FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 72 WARNING: Beginning of Configuration Data stored by the QLogic Applications. Consult documentation before editing any data past this text. ##################################################################### FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 73: Chapter 4 Operations When Using Brocade Fibre Channel Cards

    Editing the Configuration File Set the driver parameters by editing the configuration file. "4.3 Setting Up the Server" (page 74) • FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 74: Installing The Fibre Channel Card Driver

    Refer to the following Brocade web-site for instructions on how to install the driver. http://www.brocade.com/ Setting Up the Server The server setup will vary according to how the ETERNUS DX/AF storage systems and server are to be connec- ted. Only switch connections are supported.
  • Page 75: Creating A Wwn Instance Management Table For The Server

    Example: Physical slot Controller num- Instance name Physical path name name bfa0 /pci@7c0/pci@0/pci@8/bfa@0 bfa1 /pci@7c0/pci@0/pci@8/bfa@0,1 FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 76 :bfa0-port-wwn 10:00:00:05:1e:e7:45:7b :bfa1-port-wwn 10:00:00:05:1e:e7:45:7c If the WWN does not appear in the procedure above, execute the "bcu port --list" command. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 77: Setting Up The Fibre Channel Cards

    "4.3.1 Creating a WWN Instance Management Table for the Server" (page to check the port ID. Port ID check command bcu port --list FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 78 Set the port speed to "8G". # bcu port --speed 1/0 8 Setting will be enforced after port --disable and -enable FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 79 Port maximum receive data field size is 2048 - To set multiple ports, repeat the above procedure for each port. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 80: Setting The Configuration File (/Etc/System)

    After the setting is complete, check the configuration file for incorrect settings. Reboot the server. # /usr/sbin/shutdown -y -g0 -i6 FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 81: Setting Up The Server To Recognize The Logical Units

    Set the server to recognize the ETERNUS DX/AF storage systems' logical units. Execute the following commands to check the path of the ETERNUS DX/AF to be connected. Execute the following command to confirm that the server can access the logical units.
  • Page 82: Appendix A Various Management Table Templates

    Physical path name WWN Instance Management Table for Storage System WWN instance management table for storage system Channel Adapter T_ID FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 83: Target Binding Table

    Target Binding Table Target Binding Table Target binding table Server name: Channel Adapter name SCSI T_ID RAID-WWN Instance name Controller number FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris Copyright 2017 FUJITSU LIMITED P3AM-6312-18ENZ0...
  • Page 84 • operational problems as the result of errors, omissions, or the use of information in this manual. Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information • in this manual.

This manual is also suitable for:

Eternus af