Setup Configuration - Danfoss VLT Decentral FCD 300 Operating Instructions Manual

VLT® Decentral FCD

3.2.1 Setup Configuration

There is a choice of four Setups (parameter Setups), which can be pro-
grammed independently of one another. The active Setup can be selected
Active Setup
in parameter 004 . When an LCP control unit is connected,
the active Setup number will be appear in the display under "Setup". It
is also possible to preset the frequency converter to
it is possible to shift Setups using the digital inputs or serial communica-
tion. Setup shift can be used in a plant in which, for example, one Setup
3.2.2 Setup Shift
- Selection of Setup via terminals 29 and 33.
Digital input Selection of Setup, lsb
Par. 305 =
Digital input Selection of Setup, msb
Par. 307 =
Par. 004 Active setup = Multi Setup
004 Active Setup
Value:
Factory Setup (FACTORY SETUP)
Setup 1 (setup 1)
Setup 2 (setup 2)
Setup 3 (setup 3)
Setup 4 (setup 4)
Multi Setup (MULTI SETUP)
Function:
The active parameter Setup is selected here. All parameters can be pro-
grammed in four individual parameter Setups. Shifts between Setups can
be made in this parameter via a digital input or via serial communication.
Description of choice:
Factory Setup [0] contains the factory-set parameter values.
[1]-[4] are four individual Setups which can be selected as required.
Setup
[5] is used where remote-controlled shifts between the four Set-
ups via a digital input or via serial communication is required.
005 Programming Setup
Value:
Factory Setup (FACTORY SETUP)
Setup 1 (setup 1)
Setup 2 (setup 2)
Setup 3 (setup 3)
Setup 4 (setup 4)
Active Setup (ACTIVE SETUP)
is used for daytime operation and another one at night time.In parameter
006
parameter 007
converter to another by moving the LCP control panel. First all parameter
Multisetup , so that values are copied to the LCP control panel, which can then be moved to
another frequency converter. Here all parameter values can be copied
from the LCP control unit to the frequency converter.
[31]
You can select which Setup you want to programme during operation
[32] (applies both via the control panel and the serial communication port). It
is, for example, possible to programme
[5]
Setup is set to
Factory Setup
source of data if the other Setups are to be reset to a known status.
1-4
operation. If
equal to parameter 004
[0]
[1]
[2]
[3]
[4]
[5]
Setup 1-4
You can copy from the selected active Setup in parameter 005
Multi
ming setup
[0]
Copying begins when the required copying function has been selected
[1]
and the [OK]/[CHANGE DATA] key has been pushed. The display indi-
[2]
cates when copying is in progress.
[3]
[4]
[5]
MG.04.B8.02 - VLT is a registered Danfoss trademark
Setup copying
it is possible to copy from one Setup to another. Using
LCP copy
all Setups can be transferred from one frequency
Function:
Setup 1
[1] in parameter 004
Description of choice:
[0] contains the factory-set data and can be used as a
[1]-[4] are individual Setups that can be programmed freely during
Active Setup
[5] is selected, the programming Setup will be
Active Setup .
NB!
If data is modified or copied to the active Setup, the
modifications have an immediate effect on the unit's
operation.
006 Setup copying
Value:
No copying (NO COPY)
Copy to Setup 1 from #
(COPY TO SETUP 1)
Copy to Setup 2 from #
(COPY TO SETUP 2)
Copy to Setup 3 from #
(COPY TO SETUP 3)
Copy to Setup 4 from #
(COPY TO SETUP 4)
Copy to all Setups from # (copy to all)
Function:
to the selected Setup or Setups in this parameter.
NB!
Copying is only possible in Stop (motor stopped in con-
nection with a stop command).
Description of choice:
3 Programming
3
Setup 2
[2], while the active
Active Setup
.
Setup
[0]
[1]
[2]
[3]
[4]
[5]
Program-
37