Danfoss VLT Decentral FCD 300 Operating Instructions Manual page 105

4 All about FCD 300
PNU # Parameter-description
100 Configuration
101 Torque characteristics
102 Motor power P
103 Motor voltage U
104 Motor frequency f
105 Motor current I
106 Rated motor speed
107 Automatic motor adjustment
108 Stator resistance R
109 Stator reactance X
117 Resonance dampening
119 High start torque
120 Start delay
4
121 Start function
122 Function at stop
123 Min. freq. for activation of par. 122
126 DC braking time
127 DC brake engaging frequency
128 Thermal motor protection
130 Start frequency
131 Voltage at start
132 DC brake voltage
133 Start voltage
134 Load compensation
135 U/f-ratio
136 Slip compensation
137 DC hold voltage
138 Brake cut out value
139 Brake cut in frequency
140 Current, minimum value
142 Leak reactance
144 AC brake factor
146 Reset voltage vector
147 Motor type
PNU # Parameter
description
200 Output frequency range
201 Output frequency,
low limit f
MIN
202 Output frequency,
high limit f
MAX
203 Reference range
204 Minimum ref Ref
205 Maximum ref Ref
206 Ramp type
207 Ramp-up time 1
208 Ramp-down time 1
209 Ramp-up time 2
210 Ramp-down time 2
211 Jog ramp time
212 Quick stop ramp-down time
213 Jog frequency
214 Reference function
215 Preset reference 1
216 Preset reference 2
217 Preset reference 3
218 Preset reference 4
219 Catch up/slow down
reference
221 Current limit
223 Warn. Low current
224 Warn. High current
225 Warn. Low frequency
226 Warn. High frequency
227 Warn. Low Feedback
228 Warn. High Feedback
229 Frequency bypass,
bandwidth
230 Frequency bypass 1
231 Frequency bypass 2
102
Factory setting
Speed reg., open loop
Constant torque
depends on unit
M,N
depends on unit
M,N
50 Hz
M,N
depends on motor selected
M,N
depends on par. 102
Optimisation off
depends on motor selected
S
depends on motor selected
S
0 %
0.0 sec
0.0 sec
Coast in start del.
Coast
0.1 Hz
10 sec.
OFF
No protection
0.0 Hz
0.0 V
0%
depends on unit
100 %
depends on unit
100 %
0%
3.0 Hz
3.0 Hz
0%
depends on motor selected
1.30
Off
General
Factory setting
Clockwise only, 0-132 Hz
0.0 Hz
132 Hz
Min ref.-Max ref.
0.000 Hz
MIN
50.000 Hz
MAX
Linear
3.00 sec.
3.00 sec.
3.00 sec.
3.00 sec.
3.00 sec.
3.00 sec.
10.0 Hz
Sum
0.00%
0.00%
0.00%
0.00%
0.00%
160 %
0.0 A
I
MAX
0.0 Hz
132.0 Hz
-4000.000
4000.000
0 Hz (OFF)
0.0 Hz
0.0 Hz
MG.04.B8.02 - VLT is a registered Danfoss trademark
Changes during 4-setup Conv. index Data-type
operation
No Yes
Yes Yes
No Yes
No Yes
No Yes
No Yes
No Yes
No Yes
No Yes
No Yes
Yes Yes
No Yes
No Yes
No Yes
No Yes
No Yes
Yes Yes
Yes Yes
Yes Yes
No Yes
No Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
No Yes
Yes Yes
Yes Yes
No Yes
No Yes
No Yes
Yes Yes
Changes during 4-setup Conv.
operation
No Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
VLT® Decentral FCD
0 5
0 5
1 6
-2 6
-1 6
-2 7
0 6
0 5
-3 7
-2 7
0 5
-1 5
-1 5
0 5
0 5
-1 5
-1 6
-1 6
0 5
-1 5
-1 6
0 5
-2 6
-1 6
-2 6
-1 3
0 5
-1 6
-1 6
0 5
-3 7
-2 5
0 5
Data
index type
0 5
-1 6
-1 6
0 5
-3 4
-3 4
0 5
-2 7
-2 7
-2 7
-2 7
-2 7
-2 7
-1 6
0 5
-2 3
-2 3
-2 3
-2 3
-2 6
-1 6
-1 6
-1 6
-1 6
-1 6
-3 4
-3 4
0 6
-1 6
-1 6