Danfoss VLT Decentral FCD 300 Operating Instructions Manual page 43

3 Programming
direction of rotation will be maintained. If the present direction of rotation
does not respond to the reversing signal (negative reference), the refer-
ence will be set to 0.
Local operation
Shifting from
cal/remote control
, while this parameter has been set to
ated control and open loop
Configuration
100 will be active. The shift will be smooth.
Remote control
Shifting from
3
remote operation , while this parameter has been set to
control as parameter 100
If the reference signal is negative, the local reference will be set to 0.
Local operation
Shifting from
cal/remote operation
, while this parameter has been set to
operation
: The local reference will be replaced by the remote-operated
reference signal.
014 Local stop
Value:
Not active (DISABLE)
Active (ENABLE)
Function:
In this parameter, the local [STOP]-key can be engaged or disengaged
on the control panel and on the LCP control panel.
Description of choice:
Not active
If [0] is selected in this parameter, the [STOP]-key will be
inactive.
NB!
If Not active
stopped by means of the [STOP]-key.
015 Local jog
Value:
Not active (DISABLE)
Active (ENABLE)
Function:
In this parameter, the jog function on the LCP control panel can be en-
gaged/disengaged.
Description of choice:
Not active
If [0] is selected in this parameter, the [JOG]-key will be in-
active.
016 Local reversing
Value:
Not active (DISABLE)
Active (ENABLE)
Function:
In this parameter you can select/deselect the reversing function on the
LCP control panel. The key can only be used if parameter 002
mote operation is set to Local operation
control to Local control, open loop
100 [3].
40
Remote operation
to in parameter 002
Remote-oper-
[1]: The configuration selected in parameter
Local control
to in parameter 002
Remote-operated
[4]: the present reference will be maintained.
Remote operation
to in parameter 002
[0] is selected, the motor cannot be
[1] and parameter 013
[1] or Local control as parameter
MG.04.B8.02 - VLT is a registered Danfoss trademark
Description of choice:
If Disable [0] is selected in this parameter, the [FWD/REV] key will be
disabled. See also parameter 200
Lo-
017 Local reset of trip
Value:
Not active (DISABLE)
Local/
Active (ENABLE)
Function:
In this parameter, the reset function on the control panel can be engag-
ed/disengaged.
Lo-
Description of choice:
Remote
Not active
If [0] is selected in this parameter, the reset function will be
inactive.
NB!
Select
has been connected via the digital inputs.
[0]
[1]
018 Lock for data changes
Value:
Not locked (NOT LOCKED)
Locked (LOCKED)
Function:
In this parameter, it is possible to 'lock' the controls to disable data
changes via the control keys.
Description of choice:
Locked
If [1] is selected, data changes in the parameters cannot be
made; however, it will still be possible to make data changes via serial
communication. Parameter 009-012
the control panel.
019 Operating mode at power-up, local operation
[0]
Value:
[1]
Auto restart, use saved reference
(AUTO RESTART)
Forced stop, use saved reference
(LOCAL=STOP)
Forced stop, set ref. to 0
(LOCAL=STOP, REF=0)
Function:
Setting of the required operating mode when the mains voltage is en-
gaged. This function can only be active if
selected in parameter 002
[0]
Description of choice:
[1]
Auto restart, use saved ref.
drive is to start using the local reference (set in parameter 003
reference ) and the start/stop state given via the control keys immediately
Local/re-
prior to the mains voltage being cut out.
Local-
Forced stop, use saved ref.
drive is to remain stopped when the mains voltage is engaged, until the
[START]-key is activated. After a start command the motor speed is ram-
ped up to the saved reference in parameter 003
Forced stop, set ref. to 0
is to remain stopped when the mains voltage is cut back in. Parameter
003 Local reference
VLT® Decentral FCD
Output frequency range
Not active [0], only if an external reset signal
Display readout can be changed via
Local operation
Local/remote operation .
[0] is selected if the adjustable frequency
[1] is selected if the adjustable frequency
Local reference
[2] is selected if the adjustable frequency drive
is to be zeroed.
.
[0]
[1]
[0]
[1]
[0]
[1]
[2]
[1] has been
Local
.