34945A Scpi Command Summary - Agilent Technologies 34945A User Manual

5
Additional Operating Information

34945A SCPI Command Summary

Table 5-1 lists the SCPI commands that apply to the 34945A RF Switch
Platform.
As not all commands are covered in this manual, refer to the Programmer's
Reference contained on the 34980A Product Reference CD-ROM (p/n
34980-13601) for detailed information on the complete SCPI command set.
(Switch Control)
90
Table 5-1. 34945A SCPI Command Summary.
Subsystem
ROUTe:CHANnel:DRIVe:CLOSe:DEFault (@<ch_list>)
ROUTe:CHANnel:DRIVe:CLOSe:DEFault? (@<ch_list>)
ROUTe:CHANnel:DRIVe:OPEN:DEFault (@<ch_list>)
ROUTe:CHANnel:DRIVe:OPEN:DEFault? (@<ch_list>)
ROUTe:CHANnel:DRIVe:PAIRed[:MODE] {OFF|0|ON|1}, (@<ch_list>)
ROUTe:CHANnel:DRIVe:PAIRed[:MODE]? (@<ch_list>)
ROUTe:CHANnel:DRIVe:PULSe[:MODE] {OFF|0|ON|1}, (@<ch_list>)
ROUTe:CHANnel:DRIVe:PULSe[:MODE]? (@<ch_list>)
ROUTe:CHANnel:DRIVe:PULSe:WIDTh {<seconds>|MIN|MAX|DEF},
(@<ch_list>)
ROUTe:CHANnel:DRIVe:PULSe:WIDTh? [{MIN|MAX}, ] (@<ch_list>)
ROUTe:CHANnel:DRIVe:STATe? (@<ch_list>)
ROUTe:CHANnel:DRIVe:TIME:RECovery {<seconds>
(@<ch_list>)
ROUTe
ROUTe:CHANnel:DRIVe:TIME:RECovery? [{MIN|MAX}, ] (@<ch_list>)
ROUTe:CHANnel:DRIVe:TIME:SETTle {<seconds>|MIN|MAX|DEF},
(@<ch_list>)
ROUTe:CHANnel:DRIVe:TIME:SETTle? [{MIN|MAX}, ] (@<ch_list>)
ROUTe:CHANnel:LABel:CLEar:MODule <slot | ALL>
ROUTe:CHANnel:LABel[:DEFine] "<label>" , (@<ch_list>)
ROUTe:CHANnel:LABel[:DEFine]? [<type>,] (@<ch_list>)
ROUTe:CHANnel:VERify[:ENABle] {OFF|0|ON|1}, (@<ch_list>)
ROUTe:CHANnel:VERify[:ENABle]? (@<ch_list>)
ROUTe:CHANnel:VERify:POLarity {NORMal|INVerted}, (@<ch_list>)
ROUTe:CHANnel:VERify:POLarity? (@<ch_list>)
ROUTe:CHANnel:VERify:POSition:STATe? (@<ch_list>)
ROUTe:CLOSe (@<ch_list>)
ROUTe:CLOSe? (@<ch_list>)
ROUTe:MODule:BUSY? {1|ANY}
ROUTe:MODule:WAIT <slot | ALL>
ROUTe:MODule:WAIT? <slot | ALL>
ROUTe:OPEN (@<ch_list>)
ROUTe:OPEN? (@<ch_list>)
ROUTe:OPERation:OVERlap[:ENABle] {OFF|0|ON|1}
ROUTe:OPERation:OVERlap[:ENABle]?
Agilent 34945A Microwave Switch/Attenuator Driver Module User's Guide
Commands
|MIN|MAX|DEF},