Agilent Technologies 3499A Quick Reference Manual
Hide thumbs
Also See for 3499A:
- Application note (20 pages) ,
- User manual (148 pages) ,
- User manual (357 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Agilent Technologies 3499A
Summary of Contents for Agilent Technologies 3499A
- Page 1 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...
-
Page 2: View Menu
Trim to 5.5 x 9 inches. Agilent 3499A B C Switch Control System Quick Reference Guide Front-Panel Menu Reference (SCPI Mode) • Turn the knob to select an item at the current menu level. • Press Enter to move to the next level in the menu. - Page 3 á SRQ ON SRQ OFF Note: You can operate the 3499A/B/C in either the SCPI mode or the 3488A mode. • In the SCPI mode, you can operate the instrument from the front panel or over the remote interface (GPIB or RS-232) using SCPI commands.
-
Page 4: Switch Commands
SCPI Commands Quick Reference • Square brackets ([ ]) indicate optional keywords or parameters. • Angle brackets (< >) enclose parameters for which you must specify a value. Default parameters are shown in bold • A vertical bar ( | ) separates multiple parameters. Channel numbers have the form ( ), where is the slot number and... -
Page 5: Digital Input Commands
Scan Configuration Commands :SOURce <BUS|EXTernal| IMMediate |TIMer|MIX|HOLD> :SOURce? :COUNt < number >|MIN| |INFinity :COUNt? [MIN|MAX|INFinity] :TIMer < seconds >| |MAX :TIMer? [MINimum|MAXimum] TRIGger :SOURce <BUS|EXTernal| IMMediate |TIMer|MIX|HOLD> :SOURce? :TIMer < seconds >| |MAX :TIMer? [MIN|MAX] [ROUTe:] [CHANnel:]DELay < seconds >,< channel_list >|ALL [CHANnel:]DELay? <... - Page 6 Digital Configuration Commands SOURce:DIGital :MODE < slot >,< mode > :MODE? < slot > :CONTrol:POLarity < slot >,<0|1|POS|NEG> :CONTrol:POLarity? < slot > :FLAG:POLarity < slot >,<0|1|POS|NEG> :FLAG:POLarity? < slot > :IO:POLarity < slot >,<0|1|POS|NEG> :IO:POLarity? < slot > SOURce:DIGital:DATA [:< BYTE |WORD|LWORD>]:POLarity <...
-
Page 7: Status System Commands
Status System Commands STATus *CLS :OPERation:CONDition? *ESE < value > :OPERation:ENABle < unmask > :OPERation:ENABle? *ESE? :OPERation[:EVENt]? :PRESet *SRE < value > *SRE? *STB? SCPI Status System Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com... - Page 8 System Information Commands *IDN? SYSTem :CTYPE? < slot > :ERRor? :VERSion? DIAGnostic [:RELay]:CYCLes? < channel_list > [:RELay]:CYCLes:MAX? < slot > [:RELay]:CYCLes:CLEar < channel_list > System-Level Control Commands *OPC *OPC? *RST *TST? *WAI SYSTem:CPON < slot >|ALL DIAGnostic :DISPlay[:INFOrmation] < message >...
- Page 9 3488 Commands Quick Reference Channel numbers have the form , where is the slot number and the channel number. Examples are shown below. CLOSE 111 CLOSE 111,112,203,204 CLOSE 101-111 3488A Standard Commands CLOSE < channel_address >[,< channel_address > OPEN < channel_address >[,<...
-
Page 10: Error Messages
Error Messages See Chapter 6 in the 3499A/B/C User's Manual for more information. Execution Errors (SCPI Mode) Instrument Errors (3488A Mode) -101 Invalid character 100 Number of SAV/RCL out of range -102 Syntax error 101 Unable to recall - scan is running... - Page 11 Factory Default and Reset States (SCPI Mode) Input/Output Configuration Factory Default State Reset State Interface GPIB Keep current setting GPIB Address Keep current setting System Mode SCPI Keep current setting Baud Rate (RS-232) 9600 Keep current setting Parity (RS-232) Odd (7 Data Bits) Keep current setting Flow Control (RS-232) XON/XOFF...
-
Page 12: Module Description
Plug-In Module Selection Guide Multiplexer Modules Max Current Module Description Voltage Per Channel # Slots Terminal Blocks/Cables N2260A 40-Channel 200 V 1 Slot N2290A Screw Terminal N2297A DIN96-to-Twin D50 Cable N2299A DIN96-to-Quad D25 Cable N2266A 40-Channel 200 V 0.5 A 1 Slot N2290A Screw Terminal N2297A DIN96-to-Twin D50 Cable... - Page 13 1 Slot Typically SMA Connectors on (sold separately). Technical specifications external switches vary depending on external switch selection. © Copyright Agilent Technologies, Inc. 1999, 2002 Printed in Malaysia November 2002 E1102 *03499-90018* 03499-90018 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
- Page 14 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...