Omron E5CC User Manual page 335
Digital
Hide thumbs
Also See for E5CC:
- Communications manual (224 pages) ,
- Manual (39 pages) ,
- Quick start manual (38 pages)
Table of Contents
Advertisement
Changed
parameter
Related
initialized
parameters
Event Input
---
Assignment 1 to 6
Move to Protect Level
---
MV Display Selection
---
Position Proportional
---
Dead Band
Dead Band
●
*13
Hysteresis (Heating)
*13
●
Hysteresis (Cooling)
●
*13
Wait Band
●
*13
Alarm 1 to 4 Hysteresis
●
*14
ST Stable Range
*13
●
AT Hysteresis
●
*13
*18
LBA Level
●
*13
LBA Band
*13
●
*1
Initialized to input setting range upper and lower limits, or scaling upper and lower limits.
*2
Clamped by SP upper and lower limits.
*3
This parameter is initialized only when the input type is changed to analog input when the RT parameter is ON. The RT
parameter turns OFF.
*4
Initialization is performed as shown below according to the transfer output type setting. The initialization differs
depending on the changed parameter and the output type setting.
• SP: SP upper and lower limits
• Ramp SP: SP upper and lower limits
• PV: Input setting range upper and lower limits or scaling upper and lower limits
• MV (Heating): 100.0/0.0
• MV (Cooling): 100.0/0.0
• Valve opening: 100.0/0.0
*4.1 Initialized only when the transfer output type is set to SP, Ramp SP, or PV.
*4.2 Initialized only when the transfer output type is set to MV (Heating) or MV (Cooling).
*4.3 Initialized to the above default values regardless of the settings for changing the transfer output type.
*5
Initialized as follows according to the Standard or Heating/Cooling parameter setting.
• MV Upper Limit: 100.0
• MV Lower Limit: Standard 0.0, heating/cooling −100.0
*6
Initialized to control output (cooling) for heating and cooling control, according to the following.
(The defaults for standard control are the defaults in the parameter list.)
• With control output 2: The Control Output 2 Assignment parameter is initialized to control output (cooling).
• If the Controller does not have control output 2 but has four auxiliary outputs, the Auxiliary Output 4 Assignment
parameter is initialized to Control Output (Cooling).
• Otherwise, the Auxiliary Output 2 Assignment parameter is initialized to Control Output (Cooling).
*7
If the Program Pattern parameter is set to OFF, the Auxiliary Output 1 Assignment parameter is initialized as follows:
• Controllers with HB and HS alarms: Heater alarm
• Controllers without HB and HS alarms: Alarm 1
If the Program Pattern parameter is not set to OFF, the Auxiliary Output 1 Assignment parameter is initialized to the pro-
gram end output.
*8
If the Program Start parameter is assigned when the program pattern is changed to OFF, the Program Start parameter
will be initialized to "not assigned."
*9
For a temperature input, the Integral/Derivative Time Unit parameter is initialized only when the RT parameter is turned
ON. The default is as follows:
E5@C Digital Temperature Controllers User's Manual (H174)
---
---
---
---
---
---
---
---
---
---
●
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
●
*18
---
---
---
---
---
---
---
---
---
---
---
---
---
---
●
*8
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
A Appendices
---
---
---
---
---
---
---
---
●
*10
---
---
---
---
---
---
---
---
---
---
*20
●
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
●
*15
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
A - 31
---
---
---
---
---
---
---
---
---
---
---
---
---
A
Advertisement
Table of Contents
