Analog Input / Analog Input Change - GE Multilin 745 Communications Manual

DNP PROTOCOL
Analog input / analog
input change
3–6
In the following table, the entry in the Format column indicates that the format of the
associated data point can be determined by looking up the entry in Memory map data
formats on page 2–69. For example, an "F1" format is described in that section as a 16-bit
unsigned value without any decimal places. Therefore, the value read should be
interpreted in this manner.
Table 3–4: Analog input DNP points (Sheet 1 of 2)
Index when point For-
mapping is mat
Disabled Enabled
n/a 0 -
n/a 1 -
n/a 2 -
↓ ↓ ↓
n/a 118 -
n/a 119 -
0 120 F1
1 121 F1
2 122 F1
3 123 F1
4 124 F1
5 125 F1
6 126 F78
7 127 F78
8 128 F78
9 129 F78
10 130 F81
11 131 F1
12 132 F78
13 133 F79
14 134 F79
15 135 F79
16 136 F79
17 137 F82
18 138 F1
19 139 F79
20 140 F80
21 141 F80
22 142 F80
23 143 F80
24 144 F83
25 145 F1
26 146 F80
27 147 F78
28 148 F79
29 149 F80
30 150 F78
Description
User map value 1
User map value 2
User map value 3
↓
User map value 119
User map value 120
Winding 1 phase CT primary
Winding 2 phase CT primary
Winding 3 phase CT primary
Winding 1 ground CT primary
Winding 2 ground CT primary
Winding 3 ground CT primary
Winding 1 phase A current magnitude
Winding 1 phase B current magnitude
Winding 1 phase C current magnitude
Winding 1 neutral current magnitude
Winding 1 ground current magnitude
Winding 1 loading
Winding 1 average phase current magnitude
Winding 2 phase A current magnitude
Winding 2 phase B current magnitude
Winding 2 phase C current magnitude
Winding 2 neutral current magnitude
Winding 2 ground current magnitude
Winding 2 loading
Winding 2 average phase current magnitude
Winding 3 phase A current magnitude
Winding 3 phase B current magnitude
Winding 3 phase C current magnitude
Winding 3 neutral current magnitude
Winding 3 ground current magnitude
Winding 3 loading
Winding 3 average phase current magnitude
Winding 1 positive-sequence current magnitude Class 1
Winding 2 positive-sequence current magnitude Class 1
Winding 3 positive-sequence current magnitude Class 1
Winding 1 negative-sequence current
magnitude
745 TRANSFORMER PROTECTION SYSTEM – COMMUNICATIONS GUIDE
CHAPTER 3: DNP PROTOCOL
Event Notes
class
--- ---
--- ---
--- ---
--- ---
--- ---
--- ---
Class 1 2, 6
Class 1 2, 7
Class 1 2, 5,8
Class 1 2, 9
Class 1 2, 10
Class 1 2, 5,
11
Class 1 6
Class 1 6
Class 1 6
Class 1 6
Class 1 5, 9
Class 1
Class 1 6
Class 1 7
Class 1 7
Class 1 7
Class 1 7
Class 1 5, 10
Class 1
Class 1 7
Class 1 5, 8
Class 1 5, 8
Class 1 5, 8
Class 1 5, 8
Class 1 5, 11
Class 1 5
Class 1 5, 8
6
7
5, 8
Class 1 6