F36; F68 - GE Multilin 745 Communications Manual

MODBUS PROTOCOL
Table 2–4: 745 memory map (Sheet 48 of 56)
Addr Description
2212 Winding 3 restricted ground fault pickup
2213 Winding 3 restricted ground fault slope
2214 Winding 3 restricted ground fault delay
2215 Winding 3 restricted ground fault block
2216 Winding 3 restricted ground fault relays
2217 Reserved
↓ ↓
224F Reserved
Winding 1 negative-sequence time overcurrent
2250 Winding 1 negative-sequence time overcurrent function
2251 Winding 1 negative-sequence time overcurrent target
2252 Winding 1 negative-sequence time overcurrent pickup
2253 Winding 1 negative-sequence time overcurrent shape
2254 Winding 1 negative-sequence time overcurrent multiplier
2255 Winding 1 negative-sequence time overcurrent reset
2256 Winding 1 negative-sequence time overcurrent block
2257 Winding 1 negative-sequence time overcurrent relays
2258 Reserved
↓ ↓
225F Reserved
Winding 2 negative-sequence time overcurrent
2260 Winding 2 negative-sequence time overcurrent function
2261 Winding 2 negative-sequence time overcurrent target
2262 Winding 2 negative-sequence time overcurrent pickup
2263 Winding 2 negative-sequence time overcurrent shape
2264 Winding 2 negative-sequence time overcurrent multiplier
2265 Winding 2 negative-sequence time overcurrent reset
2266 Winding 2 negative-sequence time overcurrent block
2267 Winding 2 negative-sequence time overcurrent relays
2268 Reserved
↓ ↓
226F Reserved
Winding 3 negative-sequence time overcurrent
2270 Winding 3 negative-sequence time overcurrent function
2271 Winding 3 negative-sequence time overcurrent target
2272 Winding 3 negative-sequence time overcurrent pickup
2273 Winding 3 negative-sequence time overcurrent shape
2274 Winding 3 negative-sequence time overcurrent multiplier
2275 Winding 3 negative-sequence time overcurrent reset
2276 Winding 3 negative-sequence time overcurrent block
2277 Winding 3 negative-sequence time overcurrent relays
2278 Reserved
↓ ↓
227F Reserved
Winding 1 negative-sequence instantaneous overcurrent
2280 Winding 1 negative-sequence inst. overcurrent function
2281 Winding 1 negative-sequence inst. overcurrent target
2–60
Range Step
0.02 to 20.00 0.01
0 to 100 1
0.00 to 600.00 0.01
--- ---
1 to 8 ---
↓ ↓
--- ---
--- ---
0.05 to 20.00 0.01
--- ---
0.00 to 100.00 0.01
--- ---
--- ---
1 to 8 ---
↓ ↓
--- ---
--- ---
0.05 to 20.00 0.01
--- ---
0.00 to 100.00 0.01
--- ---
--- ---
1 to 8 ---
↓ ↓
--- ---
--- ---
0.05 to 20.00 0.01
--- ---
0.00 to 100.00 0.01
--- ---
--- ---
1 to 8 ---
↓ ↓
--- ---
--- ---
745 TRANSFORMER PROTECTION SYSTEM – COMMUNICATIONS GUIDE
CHAPTER 2: MODBUS PROTOCOL
Units Format Default
× CT F3 8 = 0.08 × CT
% F1 10%
s F3 10 = 0.10 s
--- F87 0 = Disabled
--- F153 None
↓ ↓ ↓
--- F30 0 = Disabled
--- F46 1 = Latched
× CT F3 25 = 0.25 × CT
---

F36

0 = Ext Inverse
--- F3 100 = 1.00
---

F68

1 = Linear
--- F87 0 = Disabled
--- F153 None
↓ ↓ ↓
--- F30 0 = Disabled
--- F46 1 = Latched
× CT F3 25 = 0.25 × CT
--- F36 0 = Ext Inverse
--- F3 100 = 1.00
--- F68 1 = Linear
--- F87 0 = Disabled
--- F153 None
↓ ↓ ↓
--- F30 0 = Disabled
--- F46 1 = Latched
× CT F3 25 = 0.25 × CT
--- F36 0 = Ext Inverse
--- F3 100 = 1.00
--- F68 1 = Linear
--- F87 0 = Disabled
--- F153 None
↓ ↓ ↓
--- F30 0 = Disabled
--- F46 1 = Latched