Opus Atlas 300 mono User Manual page 9

10
PREPARING THE TYPEFACE FONTS
PreParing tHe fontS
10
PreParing tHe fontS
10
the holes enable to distinguish between the top and the bottom of a font. the bottom hole
The holes enable to distinguish between the top and the bottom of typeface fonts. The bottom
the holes enable to distinguish between the top and the bottom of a font. the bottom hole
of a font is larger or located closer to the edge (3.2 mm and 4 mm high fonts, because of their
hole of typeface fonts is larger or located closer to the edge (3.2 mm and 4 mm high fonts,
of a font is larger or located closer to the edge (3.2 mm and 4 mm high fonts, because of their
small measurements, have only marker at the bottom).
because of their small measurements, have only marker at the bottom).
small measurements, have only marker at the bottom).
temperature
temperature
regulator
regulator
PreParing tHe matriX
11
PREPARING THE MATRIX
11
PreParing tHe matriX
11
You can order a special, customized matrix (o.matrix) from opus, made according to your own
You can order a special, customized matrix (o.matrix) from opus, made according to your own
You can order a special, customized matrix (O.Matrix) from Opus, made according to your own
design. You can also use your own matrix, however, in this case you need to use also a spe-
design. You can also use your own matrix, however, in this case you need to use also a spe-
design. You can also use your own matrix, however, in this case you need to use also a special
cial glue (o•matrix gLuE) and a plate (o.matrix base gp).
cial glue (o•matrix gLuE) and a plate (o.matrix base gp).
glue (O•Matrix glue) and a plate (O.Matrix base GP).
important! the available stamping area of the matrix is max. 13 cm
important! the available stamping area of the matrix is max. 13 cm
IMPORTANT! the available stamping area of the matrix is max. 13 cm
a. o.matrix (customized matrixes ordered in oPUS)
a. o.matrix (customized matrixes ordered in oPUS)
A. O.MATRIX (customized matrixes ordered in OPUS)
1. put the o.matrix into a special frame (o.framE matrix gp - depending on matrix size).
1. Put the O.Matrix into a special frame (O.Frame matrix GP - depending on matrix size).
1. put the o.matrix into a special frame (o.framE matrix gp - depending on matrix size).
2. insert the frame onto the heater and wait until the matrix is hot.
2. Insert the frame onto the heater and wait until the matrix is hot.
2. insert the frame onto the heater and wait until the matrix is hot.
B. CUSTOMER'S MATRIX
B. customer's matrix
B. customer's matrix
1. Glue the matrix to O.Matrix base GP plate using O•Matrix glue.
1. glue the matrix to o.matrix base gp plate using o•matrix gLuE.
1. glue the matrix to o.matrix base gp plate using o•matrix gLuE. 2. Put bounded set into a special frame (O.Frame Matrix GP).
2. put bounded set into a special frame (o.framE matrix gp).
2. put bounded set into a special frame (o.framE matrix gp). 3. Insert the frame onto the heater and wait until the matrix is hot.
3. insert the frame onto the heater and wait until the matrix is hot.
3. insert the frame onto the heater and wait until the matrix is hot.
NOTE! Before gluing the matrix, make sure that the inscription / logo on the matrix is
note! Before gluing the matrix, make sure that the inscription / logo on the matrix is
note! Before gluing the matrix, make sure that the inscription / logo on the matrix is
parallel to the bottom edge of the plate (O.Matrix Base GP).
parallel to the bottom edge of the plate (o.matrix Base gP).
parallel to the bottom edge of the plate (o.matrix Base gP).
NOTE! Detailed instructions for gluing the matrix are with O•Matrix Base GP plate.
note! Detailed instructions for gluing the matrix are with o•matrix Base gP plate.
note! Detailed instructions for gluing the matrix are with o•matrix Base gP plate.
OPUS Atlas 300 mono • User guide
atlas 300 mono • User's guide
atlas 300 mono • User's guide
important! if the frame/ typeface fonts
IMPORTANT! If the frame / typeface fonts
important! if the frame/ typeface fonts
frame
were previously used or located in the de-
frame
were previously used or located in the device,
were previously used or located in the de-
with fonts
vice, wait for 5-10 min until they cool
with fonts
wait for 5-10 min until they cool down. vice, wait for 5-10 min until they cool
down. Danger of BUrn!
Danger of Burn! down. Danger of BUrn!
2. Lock the text in the frame by means of the
2. Lock the text in the frame by means of the 2. Lock the text in the frame by means of the
3. put the frame (with the typeface fonts in)
3. put the frame (with the typeface fonts in)
3. Put the frame (with the typeface fonts in)
important! Do not touch the heater when
important! Do not touch the heater when
IMPORTANT! Do not touch the heater when
putting the frame - Danger of BUrn!
putting the frame - Danger of BUrn!
putting the frame - Danger of Burn!
4. wait for 1-2 minutes until the typeface
4. wait for 1-2 minutes until the typeface
4. Wait for 1-2 minutes until the typeface
fonts are hot.
fonts are hot.
1. put the frame on the frame Holder;
1. Put the frame on the frame Holder;
1. put the frame on the frame Holder;
compose a required text by putting
compose a required text by putting
compose a required text by putting
suitable fonts into the frame.
the typeface fonts into the frame.
suitable fonts into the frame.
note! the fonts should be put in and
NOTE! The typeface fonts should be put
note! the fonts should be put in and
taken out by means of special tweezers.
in and taken out by means of special
taken out by means of special tweezers.
the ends of the tweezers should be in-
tweezers. The ends of the tweezers
the ends of the tweezers should be in-
serted into the holes in the fonts.
should be inserted into the holes in
serted into the holes in the fonts.
the typeface fonts.
stops.
stops.
stops.
on the heater of the image press.
on the heater of the image press.
on the heater of the image press.
fonts are hot.
GB
gB
.
2
.
2
.
2
gB
9
9