Download Print this page

Opus Atlas 300 mono User Manual page 10

Hide thumbs Also See for Atlas 300 mono:

Advertisement

NOTE! The heating time of a matrix depends on its size and can vary from few to tens
Note! The heating time of a matrix depends on its size and can
of minutes. Therefore it is necessary to conduct a test to check if the matrix is hot enough.
Note! The heating time of a matrix depends on its size and can
vary from few to tens of minutes. Therefore it is necessary to
Note! The heating time of a matrix depends on its size and can
vary from few to tens of minutes. Therefore it is necessary to
conduct a test to check if the matrix is hot enough.
vary from few to tens of minutes. Therefore it is necessary to
conduct a test to check if the matrix is hot enough.
12
HOT PRINT STAMPING ON COVERS
conduct a test to check if the matrix is hot enough.
1. Put the front cover into the binding slot.
Make sure it is placed upside down.
HOT STAMPING ON COVERS
12
HOT STAMPING ON COVERS
12
2. Put the piece of hot stamping foil between
HOT STAMPING ON COVERS
12
the cover and the frame.
1. Put the front cover into the binding slot.
1. Put the front cover into the binding slot.
Make sure it is placed upside down.
NOTE! Use the magnet to fix the foil to the
1. Put the front cover into the binding slot.
Make sure it is placed upside down.
2. Put the piece of hot stamping foil between
Image Press and remove word this avoids
Make sure it is placed upside down.
2. Put the piece of hot stamping foil between
the cover and the frame.
the foil slipping down.
2. Put the piece of hot stamping foil between
the cover and the frame.
the cover and the frame.
Note! Use the magnet to fix the foil to the
3. Move the clamping lever (2) to the right
Note! Use the magnet to fix the foil to the
Image Press and avoid slipping down of the
Note! Use the magnet to fix the foil to the
- until you feel the resistance - holding the
Image Press and avoid slipping down of the
foil.
Image Press and avoid slipping down of the
cover at the same time.
foil.
foil.
4. Press the handle (1) down holding the
3. Move the adjusting lever (2) to the right
cover at the same time.
3. Move the adjusting lever (2) to the right
(until you feel the resistance) holding the cover at the same time.
3. Move the adjusting lever (2) to the right
5. Lift the handle (1), move the lever (2) to the left.
(until you feel the resistance) holding the cover at the same time.
4. Press the handle (1) down holding the cover at the same time.
(until you feel the resistance) holding the cover at the same time.
6. Take the cover out of the binding slot, remove the foil gently.
4. Press the handle (1) down holding the cover at the same time.
5. Lift the handle (1), move the lever (2) to the left.
4. Press the handle (1) down holding the cover at the same time.
5. Lift the handle (1), move the lever (2) to the left.
6. Take the cover out of the binding slot, take o the foil.
5. Lift the handle (1), move the lever (2) to the left.
NOTE! If the hot print stamping is not level you can adjust the
6. Take the cover out of the binding slot, take o the foil.
6. Take the cover out of the binding slot, take o the foil.
heater vertical or horizontal. To do this, use Allen key - size 2.
Note! If hot stamping is uneven you can adjust the heater ver-
Note! If hot stamping is uneven you can adjust the heater ver-
tical or horizontal. To do this, use Allen key - size 2.
Note! If hot stamping is uneven you can adjust the heater ver-
tical or horizontal. To do this, use Allen key - size 2.
a) Horizontal heater inclination adjustment - if the pressure
tical or horizontal. To do this, use Allen key - size 2.
is bigger on the right side, the screw need to be rotated to the
a) Horizontal heater inclination adjustment - if the pressure is big-
a) Horizontal heater inclination adjustment - if the pressure is big-
left (see the picture). However, If the pressure is bigger on the
ger on the right side, the screw need to be rotated to the left
a) Horizontal heater inclination adjustment - if the pressure is big-
ger on the right side, the screw need to be rotated to the left
left side, the screw need to be rotated to the right
(see the picture). However, If the pressure is bigger on the left
ger on the right side, the screw need to be rotated to the left
(see the picture). However, If the pressure is bigger on the left
b) Vertical heater inclination adjustment - if the pressure is bigger
side, the screw need to be rotated to the right
(see the picture). However, If the pressure is bigger on the left
side, the screw need to be rotated to the right
in the upper side, the screw need to be rotated in to the
b) Vertical heater inclination adjustment - if the pressure is big-
side, the screw need to be rotated to the right
b) Vertical heater inclination adjustment - if the pressure is big-
right side (see the picture). However, if the pressure is bigger
ger in the upper side, the screw need to be rotated in to the
b) Vertical heater inclination adjustment - if the pressure is big-
ger in the upper side, the screw need to be rotated in to the
on the bottom side, the screw need to be rotated to the left
right side (see the picture). However, if the pressure is bigger
ger in the upper side, the screw need to be rotated in to the
right side (see the picture). However, if the pressure is bigger
on the bottom side, the screw need to be rotated to the left
right side (see the picture). However, if the pressure is bigger
on the bottom side, the screw need to be rotated to the left
on the bottom side, the screw need to be rotated to the left
10
10
Note! Before sticking the matrix, make sure that the inscrip-
Note! Before sticking the matrix, make sure that the inscrip-
tion/logo on the matrix is parallel to the bottom edge of the
NOTE! Before sticking the matrix, make sure that the
Note! Before sticking the matrix, make sure that the inscrip-
tion/logo on the matrix is parallel to the bottom edge of the
plate (O.Matrix Base GP)
inscription / logo on the matrix is parallel to the bottom edge
tion/logo on the matrix is parallel to the bottom edge of the
plate (O.Matrix Base GP)
of the plate (O.Matrix Base GP)
plate (O.Matrix Base GP)
3. Put the base with a matrix on it into O.Frame Matrix GP.
3. Put the base with a matrix on it into O.Frame Matrix GP.
3. Put the base with a matrix on it into O.Frame Matrix GP.
3. Put the base with a matrix on it into O.Frame Matrix GP.
Note! In case of customized matrixes only O.Frame Matrix GP
Note! In case of customized matrixes only O.Frame Matrix GP
NOTE! In case of customized matrixes only O.Frame Matrix GP
can be used.
Note! In case of customized matrixes only O.Frame Matrix GP
can be used.
can be used.
can be used.
4. Put the frame on the back wall of the Image Press
4. Put the frame on the back wall of the Image Press
4. Put the frame on the heaters face of the Image Press
4. Put the frame on the back wall of the Image Press
front
front
cover
front
cover
magnet
magnet
cover
magnet
foil
foil
foil
1
1
1
2
2
2

Advertisement

loading