Download Print this page

Opus Atlas 300 mono User Manual page 24

Hide thumbs Also See for Atlas 300 mono:

Advertisement

12
WYKONYWANIE ZŁOCEŃ NA OKŁADKACH
1. Do szczeliny bindującej włóż złoconą okładkę. Upewnij się, że została ona włożona do góry
nogami.
2. Pomiędzy okładkę a ramkę włóż arkusz folii
Uwaga!
Przytrzymaj folię dołączonym do urządzenia magnesem, aby zapobiec jej przesuwaniu.
3. Przytrzymując okładkę, przesuń uchwyt regulujący rozwarcie szczęk (2) maksymalnie
w prawo.
Note! The heating time of a matrix depends on its size and can
4. Przytrzymując okładkę pchnij ramię urządzenia (1) w dół.
vary from few to tens of minutes. Therefore it is necessary to
5. Podnieś ramię (1), a uchwyt regulujący rozwarcie szczęk (2) przesuń w lewo.
conduct a test to check if the matrix is hot enough.
6. Okładkę wyjmij ze szczeliny bindującej, usuń folię.
e sticking the matrix, make sure that the inscrip-
n the matrix is parallel to the bottom edge of the
Uwaga!
trix Base GP)
Gdy tłoczenie jest nierównomierne, można wykonać korektę ustawienia grzałki. Potrzebny
nam będzie klucz imbusowy 2 mm. Regulacji możemy dokonać w pionie lub w poziomie.
e with a matrix on it into O.Frame Matrix GP.
HOT STAMPING ON COVERS
12
A. Pozioma regulacja odchylenia grzałki
se of customized matrixes only O.Frame Matrix GP
d.
1. Put the front cover into the binding slot.
Make sure it is placed upside down.
Jeśli docisk jest większy z prawej strony, należy śrubkę obracać w lewo (patrz rysunek A).
2. Put the piece of hot stamping foil between
me on the back wall of the Image Press
Jeśli natomiast docisk jest większy z lewej strony, obracamy śrubkę w prawo.
the cover and the frame.
B. Pionowa regulacja odchylenia grzałki
Note! Use the magnet to fix the foil to the
pends on its size and can
erefore it is necessary to
Image Press and avoid slipping down of the
Jeśli docisk jest większy w górnej części, należy śrubkę obracać w prawo (patrz rysunek B).
foil.
is hot enough.
Jeśli natomiast docisk jest większy w dolnej części, obracamy śrubkę w lewo.
3. Move the adjusting lever (2) to the right
(until you feel the resistance) holding the cover at the same time.
4. Press the handle (1) down holding the cover at the same time.
S
5. Lift the handle (1), move the lever (2) to the left.
6. Take the cover out of the binding slot, take o the foil.
slot.
Note! If hot stamping is uneven you can adjust the heater ver-
magnet
tical or horizontal. To do this, use Allen key - size 2.
ween
a) Horizontal heater inclination adjustment - if the pressure is big-
ger on the right side, the screw need to be rotated to the left
o the
(see the picture). However, If the pressure is bigger on the left
of the
side, the screw need to be rotated to the right
b) Vertical heater inclination adjustment - if the pressure is big-
ger in the upper side, the screw need to be rotated in to the
right
right side (see the picture). However, if the pressure is bigger
the cover at the same time.
on the bottom side, the screw need to be rotated to the left
he cover at the same time.
) to the left.
ot, take o the foil.
10
Note! Before sticking the matrix, make sure that the inscrip-
tion/logo on the matrix is parallel to the bottom edge of the
plate (O.Matrix Base GP)
3. Put the base with a matrix on it into O.Frame Matrix GP.
Note! In case of customized matrixes only O.Frame Matrix GP
can be used.
4. Put the frame on the back wall of the Image Press
front
cover
foil
2
magnet
1
PRZYGOTOWANIE CZCIONEK
10
front
cover
foil
Otwory pozwalają też odróżnić górę od d
przesunięty bliżej krawędzi. Czcionki o r
mają tylko znacznik określający dolną s
Rys.A
regulator
temperatury
Rys.B
PRZYGOTOWANIE MATRYC
11
Matrycę (O•Matrix) przystosowaną do w
Press możesz zamówić w firmie Opus
przekracza ona wymiarów 35 x 180 mm.
O•Matrix GLUE i przykleić ją do płytki O•
1
2
ramka
z czcionkami
A

Advertisement

loading