Opus Atlas 300 mono User Manual page 6

6
DE-BINDING METALBIND
DE-BINDING METALBIND
6
1. Put the document on the machine (back cover up).
DE-BINDING METALBIND
6
2. Push the extended back support to the maximum back position, remove the adjustable
1. Put the document on the machine (back cover up).
side guide.
2. Push the extended back support maximally to the back. And disassemble moving limiter for
1. Put the document on the machine (back cover up).
3. Lift the handle (1) delete the word to the maximum open position.
guide & bind bar.
2. Push the extended back support maximally to the back. And disassemble moving limiter for
4. Open the document a few pages away from the back cover.
3. Lift the handle (1) maximally up.
guide & bind bar.
5. Fit the right edge of the debinding wedge (5) in the right hook (4).
4. Open the document a few pages away from the back cover.
3. Lift the handle (1) maximally up.
6. Move the left end of the debinding wedge (5) over the left hook (4) and fit it there.
5. Fit the right edge of the de-binding wedge (5) in the right hook (4).
4. Open the document a few pages away from the back cover.
7. For de-binding channels 1,5 mm and 3 mm, use the debinding adapter (5).
6 . Move the left end of the de-binding wedge (5) over the left hook (4) and fit it there.
5. Fit the right edge of the de-binding wedge (5) in the right hook (4).
Place the de-binding adapter (5) on the channels, small slot is for 1,5 mm, bigger for 3 mm.
7. For de-binding channels 1,5 mm and 3 mm, use the de-binding adapter (5).
6 . Move the left end of the de-binding wedge (5) over the left hook (4) and fit it there.
Place the de-binding adapter (5) on the channels, small slot is for 1,5 mm, bigger for 3 mm.
7. For de-binding channels 1,5 mm and 3 mm, use the de-binding adapter (5).
Place the de-binding adapter (5) on the channels, small slot is for 1,5 mm, bigger for 3 mm.
4
4
back
cover
back
cover
4
4
DE-BINDING
DE-BINDING
C-BIND SYSTEM
7
C-BIND SYSTEM
7
Accessories enabling binding and de-binding of covers of the C-BIND system.
7
C-BIND SYSTEM
Accessories enabling binding and de-binding of covers of the C-BIND system.
• 2 binding inserts /A1 and B1/ in O.CB Inserts for Atlas 300/MB 300/MBE 300
(not included as standard) - (dig 1)
• 2 binding inserts /A1 and B1/ in O.CB Inserts for Atlas 300/MB 300/MBE 300
Accessories enabling binding and de-binding of covers of the CBIND system.
• de-binding wedge (dig 2) with AA jig (dig 3) in O.CB Debinding tool for Atlas 300/MB 300/MBE 300
(not included as standard) - (dig 1)
(not included as standard)
• de-binding wedge (dig 2) with AA jig (dig 3) in O.CB Debinding tool for Atlas 300/MB 300/MBE 300
• 2 binding inserts /A1 and B1/ in O.CB Inserts for Atlas 300/MB 300/MBE 300 (not included
(not included as standard)
as standard) (dig 1)
Dig 1
• De-binding wedge (dig 2) with AA jig (dig 3) in O.CB De-binding tool for
Dig 1
Atlas 300/MB 300/MBE 300 (not included as standard)
A1
A1
B1
8. Move the adjusting handle (2) to the right.
9. Press the handle (1) firmly down holding 8. Move the clamp lever (2) to the right.
8. Move the adjusting handle (2) to the right.
9. Press the handle (1) firmly down holding the the lever (2) at the same time.
9. Press the handle (1) firmly down holding
lever (2) at the same time.
10. Raise the handle (1) up, move the adjust-
the lever (2) at the same time.
10. Raise the handle (1) up, move the clamp
ing lever (2) to the right and press the han-
10. Raise the handle (1) up, move the adjust-
lever (2) to the right and press the handle
dle (1) down again. Repeat for several
ing lever (2) to the right and press the han-
(1) down again. Repeat remove word
times.
dle (1) down again. Repeat for several
severaltimes.
Lift the handle (1) up, loosen the adjusting
11.
times.
11. Lift the handle (1) up, loosen the clamp
lever (2) and remove the document to-
Lift the handle (1) up, loosen the adjusting
11.
lever (2) and remove the document together
gether with the wedge (5), then take the
lever (2) and remove the document to-
with the wedge (5), then take the wedge (5)
wedge (5) out of the document carefully.
gether with the wedge (5), then take the
out of the document carefully.
12. Make the planned changes to the docu-
wedge (5) out of the document carefully.
12. Make the planned changes to the document.
ment. The cover and channel may be re-
12. Make the planned changes to the docu-
The cover and channel may be reused
used (a maximum of three times).
ment. The cover and channel may be re-
(a maximum of three times).
used (a maximum of three times).
Dig 2
Dig 2
5
5
Dig 3
Dig 3