Opus Atlas 300 mono User Manual page 8

• Making any changes in the electrical circuit or the power supply cable may result in fire
or an electric shock.
• During a long standstill or before moving the equipment, the plug should be removed
from a mains socket
• Before removing the image press equipment from the Atlas, you must check if the heater
• after work turn off the device using a main switch
has cooled down enough, to avoid burning yourself and to place it on the work surface.
• the machine is turned off completely after removing the plug from a socket
• After work turn off the device using a main switch
• the machine should be kept away from children reach
• The equipment is turned off completely after removing the plug from a socket
• danger! the machine contains heating area – pay special attention!
• The equipment should be kept out of reach and away from children.
• the machine must not be used for any other purposes than those indicated in the oper-
• Danger! the equipment containsa high temperature heated area – pay special attention!
ating manual
• The equipment must not be used for any other purposes than those indicated in the
• it is necessary to check and supervise if the machine operates correctly. in case of any
operating manual
malfunctions, contacting the servicing point is required
• It is necessary to check and supervise if the equipment operates correctly in case of any
• the machine must not be located outside, should be operated in room temperature higher
malfunctions, contacting the servicing point is required
than +8˚C
• The equipment must not be located outside, should be operated in room temperature higher
• before removing any cover from the machine, the plug from a socket should be removed
than +8˚C
necessarily
• Before removing any cover from the equipment, the plug from a socket should be removed
• using inappropriate lubricants causes the fire hazard
necessarily
• the machine should be operated according to general safety rules
• Using inappropriate lubricants can cause a fire hazard
• any repairs can be conducted only by authorized staff
• The equipment should be operated according to general Health & Safety rules
• Any repairs can be conducted only by authorized staff
the image Press device was designed to make hot stampings on metalbind covers.
the use of fonts makes it possible to compose any inscription (various kinds of
The image Press device was designed to make hot print stamping on Metalbind
fonts, also in various languages and sizes, are available) it is also possible to
covers and channels. The use of typeface makes it possible to compose any
inscription (various kinds of typeface, also in various languages and sizes, prepare a special matrix (e.g. logo).
are available) it is also possible to prepare a special matrix (e.g. logo).
9
PreParation to WorK
9
PREPARATION TO WORK
6. turn on the switch (it is placed at the front of the housing, in the left corner). the switch
starts to light.
7. set the temperature regulator on 100˚C.
Wait until the small red led lights up, "READY" that means the required temperature has been
achieved and you are ready to start work.
wait until the led "rEadY" lights. that means that the required temperature is achieved and
the machine is ready to work.
IMPORTANT!
The best results for hot print stamping are archived, when using the OPUS supplies
important!
of hot print stamping foil and covers. To obtained the best results set the heater
the best results for hot stamping when using opus supplies (hot stamping foil and covers) are
temperature to 100 c. However, if the results are not satisfactory, a change of the
obtained with the set heater temperature of 100
setting may be necessary, in such case turn the temperature regulator right or left.
not satisfactory, a change in the settings may be necessary. in such case turn the tem-
perature regulator right (to increase the temperature) or left (in order to decrease the
1. Remove the guide & binding bar (8 thin) or (9 thick)
1. remove the thin guide&bind bar (8) or the thick guide & bind
from the binding slot.
bar (9) from the binding slot.
2. Set the extended back support to the maximum back
2. push the extended back support maximally to the back and dis-
position, remove the adjustable side guide (11)
assemble moving adjustable side stop (11).
3. Put the handle in the vertical position (1), move the
3. Lift up the handle (1), move the adjusting lever (2) maximally to
clamp lever (2) to the maximum left.
the left.
4. Assemble the image press device on the hooks (4)
4. assemble the image press device on the hooks (4) (see the pic-
(see the picture on the left).
ture on the left). 5. Insert the plug into a mains socket.
6. Turn on the Switch at the front on the left which will
5. insert the plug into a mains socket.
light up, and the heat up process starts.
7. Set the temperature to 100 °C or as required.
c. However, if the stamping results are
o