Opus Atlas 300 mono User Manual page 11

Hot StamPing on
13
HOT PRINT STAMPING
13
Hot StamPing on
13
o•cHannel BinDing cHannelS
o•cHannel BinDing cHannelS
With the Atlas 300 mono it is possible to hot print stamp on O.Channels that have been
with atlas 300 mono it is also possible to hot stamp on o.CHannELs (binding channels
covered with a special type of covering from OPUS. The O.Goldchannel base ip device
with atlas 300 mono it is also possible to hot stamp on o.CHannELs (binding channels
covered with embossed material) from opus. a o.goldchannel base ip device (available as
is available as additional equipment which is necessary for this process. .
covered with embossed material) from opus. a o.goldchannel base ip device (available as
additional equipment) is necessary for the process.
additional equipment) is necessary for the process.
1. mount the jig (b) on the o.goldchannel base ip (a) (pins of the base (a) should fix into the
1. Mount the jig (b) on the O.Goldchannel base ip (a) (pins of the base (a) should fix into the
1. mount the jig (b) on the o.goldchannel base ip (a) (pins of the base (a) should fix into the
holes of jig (b)). make sure the size of the jig (b) (indidicated on every part) is the same
holes of jig (b)). Make sure the size of the jig (b) (indidicated on every part) is the same
holes of jig (b)). make sure the size of the jig (b) (indidicated on every part) is the same
as the size of the channel you want to hot stamp on.
as the size of the channel you want hot print stamp on.
as the size of the channel you want to hot stamp on.
2. put the channel on the jig (b). make sure the bent side of the channel is located closer to
2. Put the channel on the jig (b). Make sure the bent side of the channel is located closer
2. put the channel on the jig (b). make sure the bent side of the channel is located closer to
the adjustment screws (c).
to the adjustment screws (c).
the adjustment screws (c).
3. Hang the o.goldchannel base ip (a) (with the channel) on the de-binding support (d) of
3. Hang the O.Goldchannel base ip (a) (with the channel) on the de-binding support (d)
3. Hang the o.goldchannel base ip (a) (with the channel) on the de-binding support (d) of
atlas 300 mono.
of atlas 300 mono. atlas 300 mono.
d c
d c
5. follow the same steps as in case of hot stamping with standard o.fonts.
5. follow the same steps as in case of hot print stamping with standard o.fonts.
5. follow the same steps as in case of hot stamping with standard o.fonts.
note! Hot stamping on channels is possible using 5,5 mm or 9 mm fonts only. frames 1l5,5,
NOTE! Hot print stamping on channels is possible using 5,5 mm or 9 mm typeface fonts only.
note! Hot stamping on channels is possible using 5,5 mm or 9 mm fonts only. frames 1l5,5,
3l5,5 (text should be placed in the middle line) and 1l9 should be used respectively.
Frames 1l5,5, 3l5,5 (text should be placed in the middle line) and 1l9 should be used
3l5,5 (text should be placed in the middle line) and 1l9 should be used respectively.
a
a
b
b
OPUS Atlas 300 mono • User guide
(O•CHANNELS)
a
b
a
b
Hot StamPing on cD/DvD cDcoverS
14
respectively.
Hot StamPing on cD/DvD cDcoverS
14
14 HOT PRINT STAMPING ON CD/DVD CDCOVERS
Cdcover base ip (available as additional equipment) enables to
Cdcover base ip (available as additional equipment) enables to
hot stamp on Cdcover cases using atlas 300. all those are available
CDcover base ip Is available as additional equipment which enables
hot stamp on Cdcover cases using atlas 300. all those are available
from opus.
hot print stamping on Cdcover cases using atlas 300. all those are
from opus.
available from Opus.
1. put the Cdcover base ip inside the Cdcover. two different com-
1. put the Cdcover base ip inside the Cdcover. two different com-
positions, depending on the area where you want to hot stamp,
1. Put the CDcover base ip inside the CDcover. Two different
positions, depending on the area where you want to hot stamp,
are possible:
compositions, depending on the area where you want to hot
are possible:
print stamp are possible:
• to hot stamp a text in the center of the Cdcover, direct the nar-
• To hot print stamp text in the center of the CDcover, direct the
• to hot stamp a text in the center of the Cdcover, direct the nar-
rower edge of the base (a) down
narrower edge of the base (a) down
rower edge of the base (a) down
• to hot stamp a text in the upper part of the Cdcover, direct the
• To hot print stamp text in the upper part of the CDcover, direct the
• to hot stamp a text in the upper part of the Cdcover, direct the
wider edge of the base (b) down
wider edge of the base (b) down
wider edge of the base (b) down
NOTE!
note!
• The CDcover case must be placed upside down (i.e. the spine
note!
• the cDcover case must be placed upside down (i.e. the spine of
of the case is always on the right)
• the cDcover case must be placed upside down (i.e. the spine of
the case is always on the right)
• The rubber pad of the base (at the back) should be put onto
the case is always on the right)
• the rubber pad of the base (at the back) should be put onto the
the plastic part of the CDcover case (where CD or DVD is inserted)
• the rubber pad of the base (at the back) should be put onto the
plastic part of the cDcover case (where cD or DvD is inserted)
atlas 300 mono • User's guide
atlas 300 mono • User's guide
NOTE! the adjustment screws (c) allow to
note! the adjustment screws (c) allow to
note! the adjustment screws (c) allow to regulate the position of hot stamped text:
regulate the position of hot stamped text:
regulate the position of hot stamped text:
• by turning the screws (c) clockwise the text
• by turning the screws (c) clockwise the text
• by turning the screws (c) clockwise the text
line moves closer to the bottom edge of
line moves closer to the bottom edge of
line moves closer to the bottom edge of
the channel the channel
the channel
• by turning the screws (c) counter-clock-
• by turning the screws (c) counter-clockwise
• by turning the screws (c) counter-clock-
wise the text line moves closer to the the text line moves closer to the upper
wise the text line moves closer to the
upper edge of the channel
edge of the channel
upper edge of the channel
4. there is possibility of hot stamping on the
4. There is possibility of hot stamping on the
4. there is possibility of hot stamping on the
ends of o.Channel. move the channel left or
ends of o.Channel. Move the channel left or
ends of o.Channel. move the channel left or
right on jig (b). before it, detach side stop
right on jig (b). before it, detach side stop
right on jig (b). before it, detach side stop
(10) by unscrewing it with wrench allen key
(10) by unscrewing it with the Allen key
(10) by unscrewing it with wrench allen key
attached to atlas 300.
attached to atlas 300.
attached to atlas 300.
GB
gB
gB
11