Functions - Ikegami HLM-905WR Operation Manual

(8) Contrast ratio
1000:1 (typ.)
(9) Number of display colors
16.78 million colors (8bits)
(10) Viewing angle
Vertical/horizontal: 176° (contrast ratio: 10:1 or
more)

7-4 Functions

(1) Front operation
Switch
POWER ON/OFF, MENU/ENT, PRESET,
ESC, VBS( ), CH A (
SDI[TEST] (
MONO, MARKER
Volume
CHROMA, BRIGHTNESS, CONTRAST
(BACKLIGHT), AUDIO
* With the MENU or Preset Menu screen on, the
CHA, CHB, SDI[TEST] and VBS switches
serve as arrow keys for the directions in pa-
rentheses.
* Hold down the SDI[TEST] switch, and the
built-in test signal is displayed.
* The LED indicator lights up when the POWER
and CH B switches are turned on.
(2) Marker function
a) Center marker
(Set to ON/OFF using MENU settings)
b) Safety marker
Any of the following markers is displayed
according to the image aspect ratio (4:3/16:9).
The numbers in parentheses show the aspect
at the time of marker display.
<Types>
"Safety area marker" + 100% (4:3/16:9)
The "safety area markers" are effective
over the entire screen and can be preset
1% by 1% in the range of 80-99%.
5 divided crosshatch
10 divided crosshatch
Cross
16:9 aspect marker (4:3)
15:9 aspect marker (4:3/16:9)
14:9 aspect marker (4:3/16:9)
13:9 aspect marker (4:3/16:9)
4:3 aspect marker
1.85:1 aspect marker
2.35:1 aspect marker
"Each aspect marker" + "Safety marker
in aspect" (4:3/16:9)
), CH B (
), F1, F2, ASPECT, SCAN,
(4:3/16:9)
(4:3/16:9)
(4:3/16:9)
(16:9)
(16:9)
(16:9)
The "safety marker in aspect" refers to
the safety marker with respect to the
aspect marker display zone, and can be
preset 1% by 1% in the range of 80-99%.
Corresponding to each aspect marker.
<Marker level>
Set in five steps of 20%, 40%, 60%, 80%
and100%
(3) Shadow function
Creates a shadow outside the aspect areas with 4:3
(16:9 mode), 13:9, 14:9, 15:9, 16:9 (4.3 mode),
1.85:1 (16:9 mode) and 2.35:1 (16:9 mode).
<Types>
"Various aspect markers" + "Shadow"
),
"Various aspect markers" + "Safety marker in
aspect" + "Shadow"
Shadow only
<Shadow contrast level>
Set in four steps of 0%, 20%, 40% and
60%.
(4) User marker function
Function for the user to draw their desired lines and
boxes in the unit of pixels.
a) No. of types: 10
b) No. of colors: 6
c) Drawable sizes: 1280 x 720 pixels
d) Drawing method: Switch or USB mouse
* Patent pending
(5) IMD/UMD function by TSL protocol
Function for controlling material display by using
RS485
For IMD/UMD display, either TSL or USER DIS-
PLAY should be selected (Select on the MENU).
a) Standard:
b) Connector:
c) No. of connections: Max. 32 units per line
* By increasing the number of lines, it is possi-
ble to set ID numbers and individually control
up to 126 units.
d) Protocol:
e) Characters:
f) TALLY display:
g) Display position:
(6) IMD/UMD function by User Display
Function for setting any desired name of material by
the individual input channels (including SDI-A,
SDI-B, and VBS) for displaying the name of the ma-
terial when the input channel is switched over.
For IMD/UMD display, either TSL or USER DIS-
PLAY should be selected (Select on the MENU).
- 58 -
RS485
RJ-45 (Loop through)
TSL UMD V3.1
ASCII (alphanumeric);
Max. of 8 characters in 7
colors
Red, Green, or Amber;
On-screen indication or
LED indication
Top or bottom