Specifications For Liquid Crystal Display (Lcd); Module - Ikegami HLM-905WR Operation Manual

(4) Embedded audio level meter (supported as
standard)
a) Display method
Superimposition on screen
b) Display channel
8 ch
c) Display position
4 types
d) Display mode
8 modes
e) Display segment
26 segments (including - )
f) Segment point
- , -60, -54, -48, -44, -40, -38, -36, -34, -32,
-30, -28, -26, -24, -22, -20, -18, -16, -14, -12,
-10, -8, -6, -4, -2, 0dB
g) Display color
Reference level (-18dBFS or -20dBFS) is
select in MENU.
-20dBFS
- ~ -22dB:
-20 ~ -2dB:
0dB:
18dBFS
- ~ -20dB:
-18 ~ -2dB:
0dB:
h) Peak hold
About 1 sec
i) Release time
About 0.4 sec
(5) Analog audio input (supported as standard)
a) Input terminal
3.5 Stereo mini jack type
b) Input level
0dBV max
*0dBV = 1Vrms
(6) Analog audio output (supported as standard)
a) Output terminal
3.5 Stereo mini jack type
b) Output level
0dBV max
-20dBV (digital audio data: at the -20dBFS)
*0dBV=1Vrms
c) Output impedance
75 or more
d) Input signal source
Analog audio input or embedded audio in-
put can be outputted. A signal to be out-
putted is set on MENU(DOWNMIX, CH1/2,
CH3/4, CH5/6, CH7/8).
Green
Yellow
Red
Green
Yellow
Red
(7) Headphones output (supported as standard)
a) Output terminal
3.5 Stereo mini jack type
b) Output
85 mW/ch (RL: 32
c) Input signal source
Analog audio signal or embedded audio
signal can be outputted.
To select one of these signals, make the
setting
CH3/4, CH5/6, CH7/8).
(8) Speaker output (supported as standard)
a) Rated output (monaural)
1W or more (distortion factor: 1.5%)
b) Input signal source
Analog audio input or embedded audio in-
put can be outputted. A signal to be out-
putted is set on MENU (DOWNMIX, CH1/2,
CH3/4, CH5/6, CH7/8).
* With the headphones being connected, no
sound is heard from the speakers.
7-3 Specifications for liquid crystal
display (LCD) module
(1) Number of pixels
1280 (H) x 768 (V) dots
(2) Pixel pitch
0.1515mm (W) 0.1515mm(H)
(3) Screen size (display area)
193.92mm 116.352mm
(Diagonal 22.61 cm, 9 V type)
(4) Screen brightness (brightness performance of
LCD unit)
350 cd/m (at full white input)
2
* The setting brightness differs according to
the setting value of color temperature.
(5) Drive system
a-Si TFT active matrix, line sequential
(non-interlace)
(6) Pixel arrangement
RGB vertical stripe
(7) Response speed
a) Ton + Toff: 22ms typ. ( Ta = 25°C)
* The response speed from the 10% black to
90% white level and that from the 90%
white to 10% black level are added to-
gether.
b) Gray to gray: 13ms typ. ( Ta = 25°C)
- 57 -
, distortion factor: 1%)
on MENU(DOWNMIX, CH1/2,